User Manual

MDR2400/5800-SR, Orion2410/5810-SRi and Orion 5825-SR
862-01881 Issue 12c Page 94
Object ID Object name Object Type
Access
Rights
Description
.1316.1.1.1.2.1.4.1 mdrmteLineEncodingEntry
MdrmteLineEncoding
Entry not-accessible
.1316.1.1.1.2.1.4.1.1 mdrmteLineEncodingIndex INTEGER read-only
.1316.1.1.1.2.1.4.1.2 mdrmteLineEncodingTribSelect INTEGER read-only
Selects the trib, or group
of tributaries to which
encoding applies
.1316.1.1.1.2.1.4.1.3 mdrmteLineEncoding INTEGER read-write
Defines the line code
types for the tributaries,
either HDB3 or AMI for E1
.1316.1.1.1.2.2 mdrmteRFLinkConf
.1316.1.1.1.2.2.1 mdrmteTxPower INTEGER read-write
Allows setup of the output
power available at the
diplexer port of the RF Unit
.1316.1.1.1.2.2.2 mdrmteBandPlan INTEGER read-write
The MDR5800 RF Units
operate in the 5.725 GHz
to 5.850 GHz ISM
frequency band.
.1316.1.1.1.2.2.3 mdrmteTxFrequencyPlanD INTEGER read-write
Frequency plan D allows
independent control of
transmit and receive
frequencies.
.1316.1.1.1.2.2.4 mdrmteRxFrequencyPlanD INTEGER read-write
Refer to the
mdrmteTxFrequencyPlanD
description
.1316.1.1.1.2.2.5 mdrmteTransmitBand INTEGER read-only
This value is read from the
RF Unit via the Digital
Indoor Unit and defines
whether it transmits in the
.1316.1.1.1.2.2.6 mdrmteReserved2 INTEGER read-write
.1316.1.1.1.2.2.7 mdrmteRegulations INTEGER read-only
This parameter is read
from the RF Unit via the
Digital Indoor Unit and
defines regulatory
compliance of the RF Unit
.1316.1.1.1.2.2.8 mdrmteAutoRecovery INTEGER read-write
This feature is used if the
user is installing a link
from one side and there is
no assistance on the
opposite side of the link. It
mitigates against the link
failing and not being able
to be
.1316.1.1.1.2.2.9 mdrmteOURateOverride INTEGER read-write Depracated
.1316.1.1.1.2.2.10 mdrmteOUDataRate INTEGER read-write
A setable rate that allows
a reduced transfer data
rate over the RF Link
.1316.1.1.1.2.2.11 mdrmteTxFrequencyCurrent INTEGER read-only
This value [MHz] is read
back from the RF Unit and
defines the transmit
frequency of the RF Unit
.1316.1.1.1.2.2.12 mdrmteRxFrequencyCurrent INTEGER read-only
This value [MHz] is read
back from the RF Unit and
defines the receive
frequency of the RF Unit
.1316.1.1.1.2.2.13 mdrmteNonAutoBandPlan INTEGER read-write
Same as
mdrMTEBandPlan setting
in this MIB group except
Autorecovery is not
enabled - this allows
control of the Outdoor
.1316.1.1.1.2.2.14 mdrmteNonAutoTxFreqPlanD INTEGER read-write
Same as
mdrTxFrequencyPlanD
setting in this MIB group
except autorecovery is not
enabled - this allows
control of the Outdoor