User guide

ManualsBrandsAVF ManualsFurnitureTP800-XL

13mm

Wrench

or Socket

M8 Hex Key

(1)

(XL) TV Bracket (2)

Washer

(6)

Tube (1)

Length varies for S/XL/D

Tube Bracket (2)

M8 Nut

(11)

M8 x 40

(4)

M6 x 12

(2)

Carriage Bolt

(2)

Cam Shelf (1)

5/16" Nut (Black)

(2)

M8 x 12

(2)

Cam Plate (1)

M6 Hex Key

(1)

7/16"

Wrench

or Socket

1/4" Bolt

(16)

Tower (1)

Base (1)

TP800 (S, D, XL)

Assembly and Setup Instructions

VIDEO FURNITURE INTERNATIONAL

190 Don Hillock Drive Aurora , Ontario L4G 0G9 www.video-furn.com

Toll Free: 1-877-834-3876 Fax: 1-905-751-1488 Local:905-751-1459

Note:

If you cannot understand these instructions or are concerned about safety of the installation

Contact a qualified contractor or contact VFI at 1-877-834-3876.

Not all hardware supplied will be used depending on configuration and manufacturer of your display/s.

Thank you for purchasing VFI's TP800 telepresence stand.

This product was designed for video conferencing and collaboration applications

and is compatible with most residential and commercial TV's.

Supplied Parts:

Supplied Hardware:

Tools required:

(Not Included)

Page 1

of 5

TP-1000

Hardware

Bag

Phillips

Screwdriver

TV Hardware

Bag

Camera

Hardware

Bag

(D) TV Bracket (4)

(S) TV Bracket (2)

Rev 5.0

Summary of content (5 pages)

PAGE 1
TP800 (S, D, XL) Assembly and Setup Instructions Rev 5.0 Page 1 of 5 Thank you for purchasing VFI's TP800 telepresence stand. This product was designed for video conferencing and collaboration applications and is compatible with most residential and commercial TV's. Note: If you cannot understand these instructions or are concerned about safety of the installation Contact a qualified contractor or contact VFI at 1-877-834-3876.
PAGE 2
Page 2 of 5 Assembling Stand Step 1 1) Remove M8 nuts from top of Base. Remove the back cover of the spine assembly with an M6 hex key. Align the holes on the bottom of the spine assembly with the bolts on the base and secure in place using M8 nuts. M8 Nut (5) Remove M8 nuts from base before placing tower. Use these nuts to secure Base to tower. 13mm Wrench or Socket Mounting Tube Brackets Step 2 1) Place the tube brackets at a desired height and secure in place using M8 bolts, Washers and M8 nuts.
PAGE 3
Page 3 of 5 Attaching Camera Step 3 Attach camera to cam shelf using the contents of the camera hardware bag. First attach the cam plate if your camera requires it. Optional plate for wider cameras such as Eagle eye. Camera Hardware Bag Phillips Screwdriver Mounting Camera Step 4 (For Displays over 50" this step should be done after Step 6) The cam shelf can be installed either above or underneath the TV.
PAGE 4
Page 4 of 5 Attaching TV Brackets Step 5 1. Place TV face down on blanket or non abrasive surface such as cardboard. 2. Check to see if your TV came with mounting hardware or not. If not,we have supplied the most common hardware. Most displays under 42" will use the M6 bolt. Most 42"+ will use the M8 bolts. See which bolt length you need by hand tightening only. 3. Place TV brackets so you can see the TV mounting holes through the bracket and insert bolt through a multi washer. 4.
PAGE 5
Page 5 of 5 Mounting TV Step 6 1) Run all cables from the codec through the front grommets.   2) Slide TV with attached brackets onto the installed TV bar. 3) If the camera needs to be lowered, loosen the camera bracket nuts with a 1/2" wrench while holding the camera with your other hand to prevent it from falling. You can then slide the camera to rest on top of TV and re-tighten the nuts. On Single displays after TV is hung.