Service manual
Table Of Contents
- General Information
- Operating the parameter menu
- Overview Parameter Menus
- Alphabetical Parameter List
- PRINT INFO
- PRINT PARAMETERS
- INTERFACE PARA
- SYSTEM PARAMETERS
- Foil end warning
- Foil warn stop
- Print Interpret.
- Character sets
- Character filter
- Light sens. type
- Head-sensor dist.
- Sens. punch-LS
- Foil mode
- Turn-on mode
- Error reprint
- EasyPlug error
- Single job mode
- Head resistance
- Temp. reduction
- Thin line emphas
- Voltage offset
- Miss. label tol.
- Gap detect mode
- Periph. device
- Singlestartquant
- External signal
- Start print mode
- Print contrast
- Ram disk size
- Font downl. area
- Free store size
- Print info mode
- Reprint function
- Language
- Keyboard
- Access authoriz.
- Realtime clock
- I/O BOARD
- DISPENSER PARA
- REWINDER PARA
- MLI PARAMETERS
- SPECIAL FUNCTION
- SERVICE FUNCTION
- SERVICE DATA
1. Only with INTERF.PARAM. > NETWORK PARAM. > WEB Server = „enabled“ 2. Only with BLDC firmware version V4-T36 or higher 3. Only with INTERF.PARAM. > NETWORK PARAM. > Time client = „Enabled“
4. Only with at least one data block stored in the flash memory 5. Only with rewinder 6. Only with cutter 7. Only with „AP 5.4 peripheral“ 8. Only if SYSTEM PARAMETERS > Periph. device = „Tear-off edge“ or
„Tear off + sensor“ 10. Only with activated MONARCH LANGUAGE INTERPRETER™ 12. Only if PRINT PARAMETERS > Punch mode = „Manual“ 13. Only in production mode 14. As in 13. or with a setting value
> 0 18. Only with installed RFID option 20. Only if SYSTEM PARAMETERS > Periph. device = „Dispenser“ 21. Only if SYSTEM PARAMETERS > Periph. device = „Int Rewinder“ 22. Only with an activated RFID
option 23. Only with I/O board 24. Not with I/O board 29. Availability depends on device configuration 30. Only with a memory card inserted
03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP 5.4 Gen II – AP5.6
11
AP 5.4 Parameters
(SYSTEM PARAM. cont.)
I/O BOARD PARA 23 MLI PARAMETERS 10 DISPENSER PARA 20 REWINDER PARA 21 SPECIAL FUNCTION
Reprint function
Start delay 23 Version 10 Dispense Mode 20 Rewind direction 21 Printer type 13
Language
Start print mode 23 Darkness 10 Dispenseposition 20 Current mode 13+21 Default values 13
Keyboard
Reprint Signal 23 Control Prefix 10 Display mode 20 Min rew. current 13+21 Command sequence 13
Access authoriz.
Feed input 23 Format Prefix 10 Dispense counter 20 Max rew. current 13+21 Delete job
Realtime Clock
Pause input 23 Delimiter Char 10 Application mode 20 Start rew. curr. 13+21 Delete spooler
Error output 23 Label Top 10 Start source 20 Start cur. len. 13+21 Factory settings
Error polarity 23 Left Position 10 Calibration mode 20 Pullback current 13+21 Store parameters
Status output 23 Manual Calibrate 10 Start offset 20 Back diameter 13+21 Store diagnosis
Status polarity 23 Resolution 10 Start error stop 20 Break current 13+21 EasyPl. file log 30
End print mode 23 Error Indication 10 Product length 20 Break diameter 13+21 Log files delete 30
Error Checking 10 Speed Adaption 20 Data blocks del. 4
305 DPI Scaling 10 Current mode 13+20 RFID stat. del. 22
Image Save Path 10 Min rew. current 13+20
Command ^PR 10 Max rew. current 13+20
Command ^MT 10 Start rew. curr. 13+20
Label Invert 10 Start cur. len. 13+20
Command ^JM 10 Pullback current 13+20
Back diameter 13+20
Break current 13+20
Break diameter 13+20
FW 7.34 Pre 4081