COPYRIGHT © 2010 by AVerMedia Information, Inc. All right reserved. Reproduction without permission is prohibited. No part of this document may be reproduced or transmitted in any form, or by any means without the prior written permission of AVerMedia Information Inc. AVerMedia Information Inc. reserves the right to modify its models, including their characteristics, specifications, accessories and any other information stated herein without notice.
Table of Content I. Package Contents ........................................................................................ 1 EH1004H-4 Nano ........................................................................................ 1 EH1008H-4 Nano ........................................................................................ 1 II. Hardware Installation ................................................................................... 2 A. Install the hard disk ...........................
I. Package Contents If there is any damage, shortage or inappropriate item in the package contents, please contact with local dealer EH1004H-4 Nano (1) (3) (2) (5) (4) (6) (7) (5) Power Cord (*The power cord may vary according to the local electricity system.
II. Hardware Installation A. Install the hard disk User can install 1 SATA hard disks inside the DVR unit. Follow the illustrated instructions below to install the hard disk: 1. Loosen all screws(2 sides and rear side) 2. Push the cover backward and lift. The cover is a little bit tight, please be carefully the hands. 3. Turn the cover over and place the SATA hard 4. Screw the hard disk(both side) disk (face down) inside the HDD holder.
5. Hold the cover and connect the power cable and SATA cable to the hard disk. 6. And then, turn the cover over carefully. 7. Hold the cover parallel with DVR unit and put 8. Finally, Push the cover forward and secure the cover back to the DVR unit and be the cover carefully the hard disk that inside the cover. 9. You may now connect all the cables and power on the DVR unit.
B. Device Connection Pen drive and external hard disk must be FAT32 format. i All connected devices have their own power supply are necessary. EH1004H-4 Nano i - EH1004H-4 Nano supports both Analog and IP camera in 4 channels. - 1.3 M with H.264/MPEG4/ MJPEG on the first 4 channels and 2.3M with MJPEG on the 1st channel for IP cam connection.
EH1008H-4 Nano i - EH1008H-4 Nano only supports first 4 channels for IP camera connection. - 1.3 M with H.264/MPEG4/ MJPEG on the first 4 channels and 2.3M with MJPEG on the 1st channel for IP cam connection. The back panel of the EH1008H-4 Nano user can connect up to 8 cameras in combination of analog and IP camera (EH1008H-4 Nano only support first 4 channels for IP camera connection). The DVR unit also can connect 4 sensor devices, 1 alarm devices, and output video to a LCD monitor.
EH1004H-4 Nano/EH1008H-4 Nano For backup recorded video, plugging the pen drive or external hard disk through USB port that are located at front panel of DVR unit, and then, use the bundled software enables user to transfer, playback and segment the video.
III. First Time Using the DVR Unit 1. Connect the mouse to DVR unit (through USB port). 2. Connect all necessary external devices. i DVR unit doesn’t supply the power to connected external devices. 3. Plug the power to turn on the DVR unit. 4. Please wait for a while until start up process is completed. And then, the preview screen will show up on surveillance screen. 5. Format hard disk: If the hard disk is first time installed in the DVR unit, please format the hard disk.
c. Select the hard disk from list. d. Click Format button and click Start to begin formatting e. When formatting is done, click OK. 6. Adjust time and date: Setup the DVR system date and time in order to have correct recording time and date. Following the below steps to setup date and time: a. Click Setup and enter the password (If this is the first time, enter the default password “admin”. The default ID will be “admin”). b. Select System. c.
IP camera i - EH1008H-4 Nano only supports first 4 channels (CH1~4) for IP camera. - EH1004H-4 supports both analog and IP camera in 4 channels. - 1.3 M with H.264/MPEG4/ MJPEG on the first 4 channels and 2.3M with MJPEG on the 1st channel for IP cam connection. a. Click Setup → Camera. b. Select camera channel (1~4) and mark Enable to enable the channel. c. Select Input as IP Camera. d. In Camera section, mark Display to allow the live video of camera to display on surveillance screen.
f. In IP Camera Setting window, click Protocol, and then, select Protocol, Mode, and Video Format. g. Enter IP address in IP Camera site column or enter the URL of IP camera. h. Enable Authentication and enter ID and password if IP camera’s access authority is required. i. Click OK to save the setting. j. When the IP camera has connected, user should see the camera information of Protocol, Model, Video Format, IP port, and Channel. k. To connect another IP camera, follow the above steps. IV.
V. Familiarizing the Buttons in Preview Mode Name Function (1) Logout - (2) Split Screen Mode i Reboot: To restart the DVR system. It is required to enter the password Power Off: To shut down the DVR system. It is required to enter the password Login: Using different ID to login to DVR system. Cancel: To return to DVR application. Select from four (4) different split screen types to view all the camera, or one camera over the other or alongside on a single screen.
Name Function (5) Network Enable/disable remote system access. This feature allows you to access DVR server from a remote location via internet connection. The default is disabled. (6) Setup Configure the system settings. (7) PTZ Access PTZ control panel. (8) Preview Switch to Preview mode. This allows you to view live camera display. (9) Playback Switch to Playback mode. This allows you to view the recorded video file.
VI. Playback Recoded Video 1. In preview mode, click the Playback button. Preview Mode 2. In Time and Date Selection window, select the date and time to playback. The numbers from 00 to 23 represent the time in 24-hour clock. The numbers from 01 to 08 represent the camera ID. The blue colored column indicates that there is a recorded video file on that period of time. While the red colored column indicates on where to start playing the recorded video file. 3.
VII. Familiarizing the Buttons in Playback Mode To switch in Playback mode, click Playback button at the lower right corner of Preview mode. Name (1) Split Screen Mode (2) Progress bar (3) Hour Buttons Function Select from 4 different split screen type to playback the recorded video file of all the camera, or one camera over the other or alongside on a single screen. Show the progress of the file being played. You may move the bar to seek at any location of the track.
Name Function (5) Date Select the date on the calendar and the time from 00 to 23 to where to start playing the recorded video file. The numbers from 00 to 23 represent the time in 24-hour clock. The numbers from 01 to 08 represent the camera ID. The blue colored column indicates that there is a recorded video file on that period of time. While the red colored column indicates on where to start playing the recorded video file. (6) Preview Switch to Preview mode.
Name (15) Find Next (16) Event Search (17) De-interlace Function Search for the next event or changes in the motion detector frame. You can use this when you are using Event Search function. Search from the recorded activities that were recorded in event log (i.e., Sensor, Motion, Video Loss). To enhance the video quality. Set the de-interlace mode to #1, if you are capturing motionless picture and #2, if it captures lots of movement.
