AVer SF2111H-DR User Manual
Table of Contents PREFACE ............................................................................................................................1 PRODUCT SPECIFICATIONS .............................................................................................1 PACKAGE CONTENTS .......................................................................................................4 PRODUCT INSTALLATION .................................................................................................
SYSTEM > ADVANCE > HTTPS ..........................................................................................38 SYSTEM > ADVANCE > SNMP ...........................................................................................40 SYSTEM > ADVANCE > ACCESS LIST ...................................................................................42 SYSTEM > ADVANCE > QOS/DSCP ...................................................................................43 SYSTEM > IMAGE ..............................
Preface The SF2111H-DR is a H.264 2-megapixel, full HD dome camera with 3-axis adjustment and a vari-focal lens that allows you to line up the camera precisely where you need it and capture a wide sweep or close into a narrower specific point. It has both the adjustability to capture the exact target area you require and the technology to keep that area under clear day-and-night surveillance.
Hardware LED Built-in 18 IR LED IR Distance-15M I/O 1 Sensor in / 1 Relay Out Video Out 1 Audio In 1 G.711 (64K) and G.726 (32K,24K) audio compression Input : External Mic In Audio Out 1 / Output: External Audio Out Power over Ethernet Yes Power Consumption DC12V: 5.0W (IR LED on)/3.3W (IR LED off) PoE Class 0 (IEEE802.3af): 6.3W (IR LED on), 4.4W (IR LED off) 3-Axis Gimbal Adjustments Angle Pan: 172∘ Tilt: 30∘~ 90∘ Rotation: 172∘ Dimensions 132L x 108.
System Image Snapshot Yes Full Screen Monitoring Yes Privacy Mask Yes, 3 different areas Compression Format H.
Package contents Item Descriptions 1. SF2111H-DR 2. Accessory pack 3. RJ45 socket 4. Power Adaptor (DC 12V /1A) (Optional) 5.
Product Installation Monitor Setting 1. Right-click on the desktop. Select “ Properties” 2. Change “Color quality” to “Highest (32-bit)”.
Hardware Installation and I/O Pin Assignment 1. Connect a power adapter and IP camera to PC or local network. 2. 3-Axis Gimbals Adjustments Pan: 172° Tilt: 30°~90° Rotation: 180° Once the users open the case, the gimbals adjustment offers the convenience method to install on the wall. The pan, tilt, and rotation are provided in this model. The users can adjust the gimbals with Pan 172 degrees, tilt 30~90 degrees, and rotation 180 degrees respectively.
3. Installation steps (1) Use screws to lock the bottom of camera to the ceiling or the wall. (2) Use 3-Axis to adjust the lens angle. (3) Close the dome cover. (4) Tighten the screw on the cover to fix it.
Power Over Ethernet (PoE) Set up the IP camera through Power over Ethernet (PoE). PoE is a technology that integrates power into a standard LAN infrastructure. It enables power to be provided to the network device, such as an IP camera, using the same cable as that used for network connection. It eliminates the need for power outlets at the camera locations and enables easier application of uninterruptible power supplies (UPS) to ensure 24 hours a day, 7 days a week operation. [Note] 802.3at, 15.
IP Assignment There are two ways to find IP Camera: − Finding IP Camera by using “NXU Lite recording software” − Finding IP Camera by using “IP installer” Finding IP Camera by using “NXU Lite recording software” 1. The NXU Lite software is in the attached software CD. Before launching it, please install the software first. During the installing process, users will be required to input a User name and Password for login NXU Lite system. Users can define the User name and Password as wishes.
3. Click “Setup” button. 4. Click “Add IPCam” button. 5. Select “IP Camera” item.
6. Key in IP Camera’s ID and Password (default is admin/admin) and click “Auto Search” to find camera. 7. In Search Result window, click it the IP camera model that user has purchased (Please ignore ONVIF connection item); the camera is in red text that is configurable. User can double-click on the camera is in red text and configure the IP camera’s setting; even the IP camera is not in the same IP segment. Press “OK” to back to previous screen and press”Connect” to start live view.
Finding IP Camera by using “IP installer” 1. Use the software, “IP Installer” to assign the IP address of the IP camera. The software is in the attached software CD. 2. IP installer supports two languages IPInstallerCht.exe: Traditional Chinese version IPInstallerEng.exe: English version 3. There are 3 kinds of IP configuration. Fixed IP (Public IP or Virtual IP) DHCP (Dynamic IP) DHCP server/router network automatically assigns IP addresses to devices.
IP Installer configuration: 6. IP Installer will search all IP cameras connected on the LAN. The user can click “Search Device” to search again. 7. Click one of the IP cameras listed on the left side. The network configuration for this IP camera will show on the right side. You may change the name of the IP camera to your preference (eg: Office, warehouse) in “Name” on the right side. [Note] The server name length has to be less than 15 digits.
Using DHCP Server/Router Network To use DHCP, please check DHCP and click “Submit” then click “OK”. It will apply the change and reboot the Device. Please left-click the mouse twice on a selected IP camera in “Device lists” in IP Installer. Upon doing so, the Internet Explorer browser should open.
Using NON-DHCP Server/Router Network In Non-DHCP server/router network, the static IP address must be assigned to the device each time when adding another IP camera to the network; the default IP address of the current one must be changed to avoid conflict. Please make sure the Subnet of the PC’s IP address and the IP camera’s IP address are the same. [Example] The same Subnet: IP camera IP address: 192.168.1.200 PC IP address: 192.168.1.100 Different Subnets: IP camera IP address: 192.168.2.
IP camera IP addresses: 8. A quick way to access remote monitoring is to left-click the mouse twice on a selected IP camera in “Device lists” in IP Installer. Upon doing so, the Internet Explorer browser should open.
9. Then, please key in the default “User name” and “Password”, both of which are “admin”.
Install ActiveX Control The first time you attempt to view the camera video via Internet Explorer, it will ask you to install the ActiveX component. If the installation fails, please check the security settings for the Internet Explorer browser. 1. IE Tools Internet Options… Security Tab Custom Level… Security Settings Download unsigned ActiveX controls Select “Enable” or Prompt. 2.
5 When the following dialogue box appears, click “Yes”.
Using the IP Camera Browser Interface The admin have the full access to the IP camera browser interface. The menu on the left, you can expand and navigate to access all the features. Preview Launch the Internet Explorer browser, type the IP address of the IP camera in the address field. It will show the following dialogue box. Key-in the”ID” and “Password”. The default”ID” and “Password” are both “admin”. Once connected to the IP camera, the following program interface will appear.
Name Function (3) Bandwidth Show current IP camera’s transmitting bandwidth (4) FW Version Show IP camera’s current firmware version (5) Logout Exit the application (6) Zoom control Reset zoom level. Increase zoom level. Decrease zoom level. Use the scroll bar to zoom in or zoom out the video screen (7) Capture Capture and save the image on the screen in *.bmp format (8) Record Start/stop audio and video recording. The recorded video will be saved in *.avi format.
System > General In this section, only admin level is authorized to configure the IP camera system maintenance and the date and time settings. System > General > Maintenance In the Maintenance tab, the administrator can check the system event log, upgrade the system firmware, reset the configuration settings without having to change the user management and network settings, reboot, and restore all back to factory default settings.
Name (4) Firmware Upgrade Function Upgrade the firmware to the latest version. To Upgrade the IP Camera Firmware 1. Download the file from our website and save it in your computer hard disk. 2. Click Browse. Locate and select the file and click Open. 3. Click Apply. Wait till you see the massage “Firmware Upgrade OK!!”. You may now click the Internet Explorer browser refresh button or press F5. The login page will appear.
System > General > Date & Time In the “Date & Time” tab, the administrator can set and update the system’s date and time. After filling in the correct settings, click Apply to apply the new settings. Name Function (1) Current Date & Time Display the current date and time. (2) Date Format Select the date display format. (3) Time Zone Set the local time zone. Check the box next to “Enable Daylight Saving” to enable and setup the start date and end date for daylight saving time.
Name Function (4) Setting Method Select the date & time settings method. Sync with current PC – Obtain the date and time setting on the current login computer. Sync with NTP Server – Obtain the date and time setting from NTP server. In the drop-down list, select the NTP host name. Manual – Manually set the date and time. Click “Done” to close the date and time interface.
password in “Confirm”. Then, click “Add/Set”. User List: Click edit to change the account password. To delete the user account, click Remove button. [Note] 1. The password can’t be empty, otherwise, user are not able to login successfully. 2. Please don’t use special symbols as user name such as *, %, $, &.
System > Network Setting > Setting Device Name: Used to name the IP camera to search more easily for this specific one among all connected IP cameras. Network Type: IP camera supports DHCP, static IP and PPPoE. After completed all settings, click Apply to save the configuration.
System > Network Setting > Sever Used to send out the video via Email or FTP, or to save on NAS. Mail Setting: Used to send out the video via Email. a. Login Method: Click drop-down list to select the method to login Email server – “Account” or “Anonymous”. b. Enter necessary information in “Bcc Mail”, “Sender Email Address”, “Recipient Email Address”, “Mail Server”, “Mail Server Port”, “Account Name”, and “Password” columns. c. Click “Apply” to save the configuration.
NAS Settings: Used to send out the video to NAS server. a. Enter necessary information in “Location”, “Workgroup”, “Account Name” and “Password” columns. b. If the user wants to create a new folder on the NAS server to save the video file, select “Yes” under the “Create the folder”. c. Click “Apply” to save the configuration. System > Network Setting > DDNS The IP camera supports DDNS (Dynamic DNS) service. a. Select “Enabled DDNS” to enable DDNS function. b.
Status - Common warning message: Updating! Failed(1), Please check your DNS setting. Failed(2), Please check your internet connection. Failed(3), Please check your internet connection. Failed(6), receiving data failure - Warning message from different service provider: Server Provider : dyndns.org Failed(4),Please check the Dyndns.org. Error : The system parameter given is not valid. Error : No user agent was specified. Error : The username and password pair do not match a real user.
System > Network Setting > Other 1 User may need to assign different port to avoid conflict when setting up IP assignment. Click Apply to save the configuration. HTTP Port: setup web page connecting port and video transmitting port (Default: 80) HTTPS Port: AVer IP Camera supports encrypted browsing using HTTPS.
RTP Start and End Port: in RTSP mode, you may use TCP and UDP for connecting. TCP connection uses RTSP Port (554). UDP connection uses RTP Start and End Port. ONVIF: User can enable ONVIF standard and select the ONVIF version or disable it. Security: Yes is required account and password to connect with this IP camera through ONVIF protocol. No is not required account and password to connect. (Make sure the NVR system supports ONVIF v1.02.
System > Network Setting > Other 2 Multicast Setting (based on the RTSP Server): User can setup two streaming based on the RTSP Server. Multicast operation example: The application is to get the multicast streaming in the LAN environment. Basically, the users operate VLC player, and then you can get the multicast streaming form IP camera. Please follow the steps to obtain the multicast streaming in the following steps: Step 1: 1. Implement VLC player (please download from the internet) 2.
Step 2: 2. Select Demuxers and RTP/RTSP 3. Select force multicast RTP via TRSP 1.
Step 4: Input rtsp://[IPCAM Address] / [RTSP Path] The URL address should be the same as the RTSP path in Video Stream (System-->Video Stream) 35
[Notice] a. If the received image is not from the required IP camera, please adjust the value. (Change either IP Address or Port number) b. If the Multicast stream you use doesn’t support RTSP Keepalive, please select NO.
Bonjour: This function enables MAC systems to link to this IP Camera. Please key in the name here (Safari supports Bonjour protocol). LLTD: If your PC supports LLTD, enable this function then you can check the connection status, properties, and device position (like IP address) of this IP Camera in the network map. In the computer running Windows Vista or Windows 7, you can find LLTD through the path Start Control Panel Network and internet Network and Sharing Center Click “ See full map”.
System > Advance > HTTPS HTTPS (Hypertext Transfer Protocol Secure): Https can help protect streaming data transmission over the internal on the higher security level. You can select the connection type. "Https" means user cannot connect the camera via Http protocol. The HTTPS path will be: "https ://( IP address)/". If you select "Http & Https", both the Http and HTTPS path can be used to access the camera Remove the existing setting: Before setting new request, please remove old secure identification.
Created Request: Setting the secure identification and apply it. There are two ways to set Certificate- Install Signed Certificate or Create Self-Signed Certificate.
System > Advance > SNMP SNMP (Simple Network Management Protocol) provides a simple framework for administering networked hardware. To manage the IP camera, you have to prepare a MIB browser or similar tools first. SNMPv1, SNMPv2c, and SNMPv3 can be enabled simultaneously. SNMPv1 and SNMPv2: The term "Community name" in SNMPv1 and SNMPv2c can be roughly regarded as key. The person who has the community name has the authority to read or edit the information of IP camera via SNMP.
SNMPv3: For data security reason, the authentication and encryption assurances are added when developing SNMPv3. The user has to give not only the security name (the same as "community name" in v1&v2c, or sometimes we call it "context name") but the password in order to access the IP camera. Please set security name, authentication type, authentication password, encryption type, encryption password of write and read respectively. The password must be 8~64 bits in length.
System > Advance > Access list You can deny an IP address or a range of IP address so that they cannot access the IP camera. Tick the "enable" box, key in the IP address you want to deny, select" deny" then click "Add" to add it to the list. You can also choose to deny a range of IP address but allow one or several IP address of them. Take the picture above for example, IP address192.168.50.151~161 is not allowed to connect to the camera, but only 192.168.50.159 can access.
System > Advance > QoS/DSCP QoS/DSCP(Quality of Server/Differentiated Services Code-point) specifies a simple mechanism for classifying and managing network traffic and provide QoS on IP networks. DSCP is a 6-bit in the IP header for packet classification purpose. The number 0~63 for Live Stream, Event / Alarm, and Management represent the ratio that the bandwidth is divided. For example, if you set5, 10, and 20 for the three items, then the bandwidth of the three item is 5:10:20.
System > Image Admin and operator levels can adjust the Image setting. There are 5 tabs: OSD, Preference, Exposure, Advanced, and Privacy Mask System > Image > OSD In OSD tab, you can enable/disable overlaying time stamp and text title. After completing the setting, click Save to apply the new setting and Cancel to keep the new setting. Time Stamp: Mark Enable check box and select a position where date and time stamp / text to display on video screen.
System > Image > Preference In Preference tab, you can tune the IP camera white balance, change the video orientation, and adjust the brightness and contrast. White Balance: Adjust white balance value. Video Orientation: To Flip or Mirror the video on screen. D-WDR: This function is able to reduce the contrast in the view to avoid the dark zones resulting from over and under exposure. Adjust “Brightness”, “Contrast”, “Hue”, “Saturation” to get clear video.
System > Image > Advanced Click Default button will back to factory default setting. Sense-UP: The main purpose of sense-up is to provide a camera technology that does not rely on artificial light to see in very low light conditions. By The shutter stays open longer, allowing more light into the camera and seeing better in low light. This setting altogether when there is a moving object in the image and the faster the object moves, the worse the image appears (blurriness).
System > Image > Privacy Mask For the security purpose, there are three areas can be setup for privacy mask. Click Area #(Area 1, Area 2, Area 3)button first and drag a area on the image screen. Then, click Save button to save the setting.
System > Video Stream> General Input Resolution: Select the video resolution that is the maximum resolution supported in Stream 1 and Stream 2. Video System: Select the video format. TV Output: Select the video format of TV Output.
System > Video Stream > Stream1 Basic Mode Click Apply to save the configuration. − Resolution: There are 8 resolutions can be chosen – 1920x1080, 1280x720, 640x480, 320x240, 176x144. − Profile: Profiles are different compression way of H.264. High profile provides better coding efficiency. Note that some devises do not support every profile. For example, iPhone4 only supports Main profile. − Quality: There are 5 levels to adjust – Best, High, Standard, Medium, and Low.
VBR: 1(Low) ~10(High) – Compression rate, the higher the compression rate, the better the picture quality is; vise versa. The balance between VBR and network bandwidth will affect picture quality. Please carefully select the VBR rate to avoid picture breaking up or lagging. − − − − Video Frame Rate: The video refreshing rate per second. GOP Size: It means "Group of Pictures". Video Format: H.
System > Video Stream > Stream2 Basic Mode Click Apply to save the configuration. − Resolution: There are 8 resolutions can select -- 1920x1080, 1280x720, 640x480, 320x240, 176x144. − Profile: Profiles are different compression way of H.264. High profile provides better coding efficiency. Note that some devises do not support every profile. For example, iPhone4 only supports Main profile. − Quality: There are 5 levels to adjust – Best, High. Standard, Medium, and Low.
Advanced Mode Click Apply to save the configuration. − Resolution: There are 8 resolutions can select -- 1920x1080, 280x720, 640x480, 320x240, 176x144. − Profile: Profiles are different compression way of H.264. High profile provides better coding efficiency. Note that some devises do not support every profile. For example, iPhone4 only supports Main profile − − − − − Rate Controls: CBR or VBR Video Bitrate: Select the bitrate of video. Video Frame Rate: The video refreshing rate per second.
System > Video Stream > Stream3 3GPP Streaming is designed for mobile viewing. Stream 3 Setting: Enable or Disable 3GPP Streaming. 3GPP Path: It’s a URL address. [Note] 1. 3GPP mode video spec: 320x240 resolutions, 15FPS, H.264 format. (Audio: AMR) 2. To get the best mobile viewing quality, please download AVeriViewer (AndroidViewer) from the Apple App store or Google Play. iViewer takes video from Stream 1 or Stream 2, not from 3GPP streaming.
System > Audio IP camera supports 2-way audio (mono). User can send audio from IP camera built-in MIC (depending on different models) to remote site; User can also send audio from remote site to IP camera’s external speaker. a. IP camera to PC: select “Enable” to start this function. b. In live video screen, click button to start chatting. Press again to mute.Click button to turn on or off the speaker of PC. [Note] The Audio will not be smooth when enable SD/SDHC card recording function simultaneously.
System > SD Card Please Insert SD/SDHC card before use it. Make sure pushing SD/SDHC card into the slot completely. [Note]The use of the SD/SDHC card will affect the operation of the IP camera slightly, such as affecting the frame rate of the video.
Event > Arrangement > Motion Motion Detection: IP camera allows 3 areas motion detection. When motion is triggered, it can send the video to some specific mail addresses, transmit the video to remote ftp server, trigger the relay, and save video to local SD/SDHC card. To set up the motion area 1, click “Area 1” button. Using mouse to drag and draw the area. The same operation for area 2 and 3. value is, the more sensitive to trigger event.
Event > Arrangement > Preference Record File: File Format: IP camera allows 3 different types of recording file to change its record size. When motion/alarm is triggered, there are 3 different types of record mode. − AVI File (With Record File Setting ) − JPEG Files (With Record File Setting), only with M-JPEG compression format. − Single JPEG (Single File with Interval Setting)(JPEG photo).
Event > Schedule Schedule: After complete the schedule setup, the camera data will be recorded according to the schedule setup. Snapshot: After enable the snapshot function; user can select the storage position of snapshot file, the Interval time of snapshot and the reserved File Name of snapshot.
Event > DI/DO IP camera supports 1 input/1 output (depending on different models). When input is triggered, it can send the video to some specific mail addresses, transmit the video to remote ftp server, trigger the relay, and save video to local SD/SDHC card. CAUTION!! Please connect to propriety relay box to reduce the risk of electric shock & damaged. Input Setting: Input 1 sensor: This is to set the relay status while sensor is not yet triggered.
Output Setting: Mode setting: OnOff Switch: Relay status is based on sensor triggered times. Time Switch: To restore the original relay status after the interval time. [Note]GPIO pin define please refer to the part of Front / Back plane & I/O port pin assignment.
Network Configuration Configuration 1 a. Internet Access: ADSL or Cable Modem b. IP address: More than one real IP c. IP camera and PC connect to the internet d. For fixed real IP, set up the IP into IP camera and PC. For dynamic IP, start PPPoE.
Configuration 2 a. Internet Access：ADSL or Cable Modem b. IP address：one real IP c. IP camera and PC connect to the internet d. Device needed：IP sharing e. Use virtual IP, set up port forwarding in IP sharing.
Factory Default 1. To recover the default IP address and password, please follow the following steps. 2. Remove power, and press and hold the button. Please refer to the picture below. Reset button 3. Power on the camera. Don’t release the button during the system booting. 4. It will take around 30 seconds to boot the camera. 5. Release the button when camera finishes proceed. 6. Re-login the camera using the default IP (http://192.168.1.200) or DHCP, and user name (admin), password (admin).
Troubleshooting Here are some useful tips on how to solve some common problems. Problem Solution I forgot the account and password for Please refer to the manual of “VI Factory Default SF2111H-DR. How can I go back to setting” description. default setting? I can’t find a way to force day mode and We don't provide this function due to the limitation of night mode. Is this possible and how. hardware. I recorded video file in H.264 file format Default Windows Media Player doesn’t have H.
Appendix SF2111H-DR is compliant with SD/SDHC card and to ensure recording quality, and please use memory cards over 2G and Class 4 above (Max.
COPYRIGHT © 2012 AVer Information Inc. All rights reserved. All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form, or by any means without the prior written permission of AVer Information Inc. is prohibited. AVer Information Inc. reserves the rights to modify its products, including their specifications and any other information stated herein without notice.
Limited Warranty AVer Information, Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms to AVer’s documentation for the product and that its manufacture and components are free of defects in material and workmanship under normal use. “You” as used in this agreement means you individually or the business entity on whose behalf you use or install the product, as applicable. This limited warranty extends only to You as the original purchaser.
Governing Law and Your Rights This warranty gives you specific legal rights; You may also have other rights granted under state law. These rights vary from state to state.
