FV2006 Mini Vantal Dome IP Camera Quick User Guide
Table of Contents Before Installation .................................................................................................................1 I. Camera Introduction ....................................................................................................1 1. Package Contents ...............................................................................................1 2. Hardware Installation ........................................................................................
ENGLISH Before Installation Before installation, please be sure to read this quick installation guide and user’s manual carefully to complete the installation. I. Camera Introduction The following section introduces package contents, hardware installation, factory default reset, and SD card Compatibility List of each type camera. 1. Package Contents Item Descriptions 1. FV1306 2. Accessory pack 3. Conversion ring 4. Power Adaptor(DC 12V/0.5A) (Optional) 5.
2. Hardware Installation 1. Set the camera Locate cable from bottom a. Use three screws to lock the base of camera on the ceiling or the wall. b. Put back the cover, and turn it tightly to get waterproof.
ENGLISH Locate cable from side a. Open the conversion ring package in accessory. It includes a conversion ring and two set of screws. b. Use three screws to lock the conversion ring on the ceiling or the wall. c. Use three screws to combine the base of camera with the conversion ring. The cable can pass through the hole on the side of conversion ring. d. Put back the cover, and turn it tightly to get waterproof.
2. When removing the dome cover, you can see the Micro SD card slot and the reset button. 3. I/O Interface I/O Connection a. Please connect the GND & DO pin to the external relay (buzzer) device. b. Please connect the GND & DI pin to the external trigger device.
ENGLISH 2.1 Factory Default 1. To recover the default IP address and password, please follow the following steps. 2. Remove power and Ethernet cable and the dome cover. 3. Press and hold the button and connect power and Ethernet cable to the camera again and hold for round 20 seconds for system booting. 4. Release the button when camera finishes proceed. 5. Re-login the camera using the default IP (http://192.168.1.168) or DHCP, and user name (admin), password (admin).
3. SD card Compatibility List FV2006 is compliant with microSD/SDHC card and to ensure recording quality, and please use memory cards over 2G and Class 4 above (Max.
ENGLISH II. Monitor Setting 1. Right-click on the desktop. Select “ Properties” 2. Change “Color quality” to “Highest (32-bit)”.
III. IP Assignment There are two ways to find IP Camera: − Finding IP Camera by using “NXU Lite recording software” − Finding IP Camera by using “AVer IPCam Utility” Finding IP Camera by using “NXU Lite recording software” 1. The NXU Lite software is in the attached software CD. Before launching it, please install the software first. During the installing process, users will be required to input a User name and Password for login NXU Lite system. Users can define the User name and Password as wishes.
ENGLISH 3. Click “Setup” button. 4. Click “Add IPCam” button. 5. Select “IP Camera” item.
6. Enter the IP Camera’s ID and Password (default is admin/admin) and click “Auto Search” to find camera. 7. In Search Result window, click it the IP camera model that user has purchased (Please ignore ONVIF connection item); the camera is in red text that is configurable. User can double-click on the camera is in red text and configure the IP camera’s setting; even the IP camera is not in the same IP segment. Press “OK” to back to previous screen and press”Connect” to start live view.
ENGLISH Finding IP Camera by using “AVer IPCam Utility” 1. Use the software, “AVer IPCam Utility” to assign the IP address of the IP camera. The software is in the attached software CD. 2. Run the IPCam Utility 3. Select the proper network adapter and click [Search] to begin searching. 4. Select and double click the IP camera you want to access. If you want to change the setting of the selected IP camera, enter the user ID, correct password, and change the settings and then click [Apply].
5. The IE browser will open and direct you to IP camera login page. This requires IPViewer.ocx to run. If the IE ActiveX warning message appears, click to allow running the add-on. [Note] The default IP address is: 192.168.1.168 The default ID and Password are both ”admin”. It is not allowed to enter device name in Chinese and any other special characters (' " \ & ^). Gateway number can’t be “0”.
ENGLISH Using NON-DHCP Server/Router Network In Non-DHCP server/router network, the static IP address must be assigned to the device each time when adding another IP camera to the network; the default IP address of the current one must be changed to avoid conflict. Please make sure the Subnet of the PC’s IP address and the IP camera’s IP address are the same. [Example] The same Subnet: IP camera IP address: 192.168.1.168 PC IP address: 192.168.1.100 Different Subnets: IP camera IP address: 192.168.1.
IP camera IP addresses: A quick way to access remote monitoring is to double-click on a selected IP camera in “Camera Name list” in AVer IPCam Utility. Then, the IE browser will open and connect to IP camera. Then, please key in the default “ID” and “Password”, both of which are “admin”.
ENGLISH IV. Connecting the IP Camera Launch the Internet Explorer browser, type the IP address of the IP camera in the address field. It will show the following dialogue box. Key-in the ”ID” and “Password”. The default ”ID” and “Password” are both “admin”. Once connected to the IP camera, the following program interface will appear.
COPYRIGHT © 2013 AVer Information Inc. All rights reserved. All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form or by any means without the prior written permission of AVer Information Inc. is prohibited. All information or specifications are subject to change without prior notice. “AVer” is a trademark owned by AVer Information Inc. Other trademarks used herein for description purpose only belong to each of their companies.
Limited Warranty AVer Information, Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms to AVer’s documentation for the product and that its manufacture and components are free of defects in material and workmanship under normal use. “You” as used in this agreement means you individually or the business entity on whose behalf you use or install the product, as applicable. This limited warranty extends only to You as the original purchaser.
Governing Law and Your Rights This warranty gives you specific legal rights; You may also have other rights granted under state law. These rights vary from state to state.
