Use and Care Manual

ManualsBrandsAVENLI ManualsInflatable Pools10 ft. Round 30 in. Deep Metal Frame Pool Above Ground Swimming Pool Family Set

Test Report

No.: SHHL1909051579IF Date: NOV. 25, 2019 Page: 1 of 19

SHANGHAI JILONG PLASTIC PRODUCTS CO., LTD

2555 XIUPU ROAD, PUDONG AREA, SHANGHAI

Sample Description : ROUND STEEL FRAME POOLS

Item No. : 17798/17798* (*=ABBREVIATION OF COUNTRY)

Manufacturer : JILONG PLASTIC PRODUCTS (JIANGSU) CO., LTD

************

Sample Receiving Date : SEP. 17, 2019

Testing Period : SEP. 17, 2019 TO NOV. 25, 2019

Testing Location : 3

BUILDING, LANE 3999, XIUPU RD., PUDONG

DISTRICT, SHANGHAI, CHINA

Test Performed : SELECTED TEST(S) AS REQUESTED BY APPLICANT

Test Requested : 1. EN 16582-1:2015 DOMESTIC SWIMMING POOLS

PART 1: GENERAL REQUIREMENTS INCLUDING

SAFETY AND TEST METHODS

2. EN 16582-3:2015 DOMESTIC SWIMMING POOLS

PART 3: SPECIFIC REQUIREMENTS INCLUDING

SAFETY AND TEST METHODS FOR ABOVEGROUND

POOLS

Test Result(s)

: FOR FURTHER DETAILS, PLEASE REFER TO THE

FOLLOWING PAGE(S)

Conclusion

: THE SUBMITTED SAMPLE MET THE TEST

REQUIREMENT.

Signed for and on behalf of

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.

_________________

Yomoro Gu

Authorized Signatory

Summary of content (19 pages)

PAGE 1
Test Report No.: SHHL1909051579IF Date: NOV. 25, 2019 Page: 1 of 19 SHANGHAI JILONG PLASTIC PRODUCTS CO., LTD 2555 XIUPU ROAD, PUDONG AREA, SHANGHAI Sample Description : ROUND STEEL FRAME POOLS Item No. : 17798/17798* (*=ABBREVIATION OF COUNTRY) Manufacturer : JILONG PLASTIC PRODUCTS (JIANGSU) CO., LTD Sample Receiving Date ************ : SEP. 17, 2019 Testing Period : SEP. 17, 2019 TO NOV. 25, 2019 Testing Location : 3TH BUILDING, LANE 3999, XIUPU RD.
PAGE 2
Test Report No.: SHHL1909051579IF Date: NOV. 25, 2019 Page: 2 of 19 Test Conducted: 1. EN 16582-1:2015 Domestic swimming pools Part 1: General requirements including safety and test methods 2. EN 16582-3:2015 Domestic swimming pools Part 3: Specific requirements including safety and test methods for aboveground pools Sample Size: 1 piece Clause Test Method / Requirement 1. EN 16582-1:2015 4. General requirements and test methods 4.
PAGE 3
Test Report Clause No.: SHHL1909051579IF Date: NOV. 25, 2019 Page: 3 of 19 Test Method / Requirement Once installed, the swimming pool shall be watertight according to one of the classes of Table 1 as stated in the point of sale information. The measurement of any water loss should be carried out over a period of 7 days.
PAGE 4
Test Report Clause 4.4.2 Specific requirements and testing for corrosion resistance 4.4.3 Osmosis resistance of composites and polymers No.: SHHL1909051579IF Date: NOV.
PAGE 5
Test Report Clause 4.4.4 Wood 4.5 Injury risks 4.5.1 Small elements, edges and corners No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement Protect the sample on its edges and its rear face, to avoid contact with water. On completion of this test, no blister (i.e. density 0), porosity, cracking or fibre prominence, shall be detected on the surface after testing, compared to a control specimen as defined in EN ISO 4628-2.
PAGE 6
Test Report No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement For example, edges can be bevelled or rounded, and surfaces shall be smooth and free from burrs. Examples are provided in Figure 4. If they are due to a wall thickness lower than 4 mm, one of the following requirements applies: - they shall be folded, rolled or wound in spirals according to Figure 4 d); - they shall be protected by a plastic coating or by any other suitable means as shown in Figure 4 e). 4.5.
PAGE 7
Test Report No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement children (especially those under the age of five years) by striding over/climbing over is limited. The secure access to the basin is met when: - the height between the highest bearing point (according to the requirements stated in 5.5) and the upper level of the finished pool is greater than or equal to 1 100 mm or; - the height between the ground and the lowest bearing point (according to the requirements stated in 5.
PAGE 8
Test Report Clause No.: SHHL1909051579IF Date: NOV. 25, 2019 Page: 8 of 19 Test Method / Requirement The slip resistance requirements only refer to walking surfaces of slopes, steps and treads located on the inner side of the basin, under the water line or not, and allowing the user to go down into the water. These requirements do not apply to: - slopes or steps that are not intended to enter the water ; - water slides; - starting platforms; - diving boards, or - any similar equipment.
PAGE 9
Test Report Clause 5.4 Ladders 5.4.1 Dimensions No.: SHHL1909051579IF Date: NOV. 25, 2019 Page: 9 of 19 Test Method / Requirement If the use of the means of access creates a fall height of more than 600 mm above the floor inside and outside the pool, this can lead to a partial fall, resulting in a potential risk of strangulation, therefore the permissible openings shall be between 25 mm and 110 mm, or greater than 230 mm.
PAGE 10
Test Report Clause 5.4.4.2 Ladders with lifting access 5.4.4.3 Ladders with retractable access 5.4.4.4 Means of access to the deck (ladder or stairs) 5.4.5 Other requirements No.: SHHL1909051579IF Date: NOV.
PAGE 11
Test Report No.: SHHL1909051579IF Date: NOV. 25, 2019 Clause Test Method / Requirement 5.5.2 Raised bearing points 5.5.2.1 Contour In the control plane, the contour is the envelope curve of all the protuberances appearing in this plane forms the contour. The contour is read from the face to be controlled outwards (see Figure 11). 5.5.2.2 Control In the appropriate control area, the control plane is the plane vertical plane intersecting the protuberances (see Figure 11). 5.5.2.
PAGE 12
Test Report No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement The installation and bracing instructions shall be supplied with stairs. The constituent material or coating of the stairs shall allow easy maintenance. 5.6.2 Built-in Built-in stairs that are part of the swimming pool structure stairs shall conform to the general characteristics as defined in 4.4 and 5.4.2. 5.6.
PAGE 13
Test Report Clause 6.2.2 Installation and commissioning manual No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement - the maximum effective water depth (see models in Figure 14); - the maximum total overall dimension (see models in Figure 14); - the effective volume of water; - all indications regarding the construction of reinforcement works related to the kit type; - the composition of the swimming pool kit (examples: pool structure, ladder, filtration system, etc.
PAGE 14
Test Report No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement - all of the structural works necessary for the proper construction of the structure. 6.2.3 Operating The swimming pool kit shall be accompanied by an operating and and maintenance manual. These manuals shall contain all of maintenance the information necessary for a correct use of the pool manual structure.
PAGE 15
Test Report Clause No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement structure. The operating and maintenance manual shall also contain: - the safety instructions (see Annex B); - recommendations concerning the filling level; - if appropriate, recommendations concerning the need to monitor bolts and screws; splinters or any sharp edges; - a warning about the hazards resulting from complete emptying of the basin; - recommendations on winterising and long-term storage. 6.
PAGE 16
Test Report Clause 4.1 General No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement For new basin designs and for existing basin constructions that are structurally modified, the following tests shall be carried out with at least one test sample. 4.2 Aboveground swimming pool with frame-supporting walls 4.2.1 On completion of the test defined in 4.2.1.2, the swimming Resistance to pool shall not collapse and shall meet the requirements set horizontal forth in EN 16582-1:2015, 4.5.
PAGE 17
Test Report Clause swimming pool with tubular frame and/or flexible structure No.: SHHL1909051579IF Date: NOV. 25, 2019 Test Method / Requirement - Wall tear resistance according to EN 1875-3 and EN ISO 4674-2. Acceptable results: - warp direction: 10 DaN; - weft direction: 5 DaN. - Wall/wall weld tensile/breaking strength according to EN ISO 1421. Acceptable results: - warp direction: 100 DaN/50 mm; - weft direction if applicable: 100 DaN/50 mm. - Adhesion test according to EN ISO 2411.
PAGE 18
Test Report No.: SHHL1909051579IF Date: NOV. 25, 2019 Page: 18 of 19 Result 1 Mechanical strength of the membrane of a swimming pool with tubular frame and/or flexible structure Adhesion Strength (EN ISO 2411:2017;) N/A= Not Applicable, The Specimen Could Not Be Peel Off Separately Tearing Strength (EN ISO 4674-2:1998; Elmendorf) Warp Yarns Torn Weft Yarns Torn Unit daN daN (A) >12.8 6.1 Requirement 10daN 5daN (A) 175.0 120.
PAGE 19
Test Report No.: SHHL1909051579IF Date: NOV.