Instruction manual

17
TCP/IP
Version of the VSI-Pro that support: V13.00, V13.10,
V13.24 and V13.34.
Press the “Up” or “Down” button to move the cursor to
“REGISTER SELECT” and press “Set”. The REGISTER
SELECT menu will appear:
Figure 10: REGISTER SELECT Sub-Menu
VSI-Pro VIDEO SERIAL INTERFACE
Figure 11: TCPIP Sub-Menu
1. Press the “Up” or “Down” button to move the cursor to
“TCPIP” and press “Set”. The TCPIP menu will appear:
NOTE: The TCPIP232 Adapter can be programmed by
this method or by using a standard PC with a serial cable
along with a Serial Program Terminal such as
HyperTerminal. Refer to the TCIP232 Adpater Manual for
doing this.
Once you have set the IP Address of the TCPIP232
Adapter you will be in the “Generic” display mode. You
may select another register driver to format this display.
When you do this the VSI-Pro loads the default register
baudrate as if a direct connection to the register so make
sure you set the proper baudrate as described below.
The TCPIP232 Adpater communicates with the VSI-Pro
via RS-232 at a baudrate of 19.2K. Therefore when you
select this menu option the baudrate of the VSI-Pro is
changed to this rate so communication for downloading
the configuration can occur. When using the TCPIP232
adpater with other register drivers or data dump mode
make sure you change the RXD baudrate to 19.2K so the
VSI-Pro will communicate.
GENERIC
TCPIP
ADDRESSABLE VSI
PC COM 1,2,3,4
AD4323
ADS
DELTA SONO 3.1
DRESSER WAYNE
EDACOM
- - - - - - - - - NEXT PAGE
EXIT
IP ADDRESS
DISPLAY INFORMATION
DOWNLOAD CONFIGURATION
EXIT
EXAMPLE: If the IP address is 192.168.0.141, set the
address on the TCPIP 232 Adapter using this menu.
Press the “Up” or “Down” button to move the cursor to “IP
ADDRESS” and press “Set” to enter and change the IP
Address to the same as the IP Address you wish to
monitor.
Figure 12: IP Address Sub-Menu
IP ADDRESS 1 192
IP ADDRESS 2 168
IP ADDRESS 3 0
IP ADDRESS 4 141
EXIT
3. Press the “Up” or “Down” button to move the cursor to
“DISPLAY INFORMATION” and press “Set” to enter the
Display Information sub-menu.
2. Press the “Up” or “Down” button to move the cursor to
“EXIT” and press “Set” to return to the previous menu.
4. Press the “Up” or “Down” button to move the cursor to
“EXIT” and press “Set” to return to the previous menu.
INFORMATION 0 ON
INFORMATION 1 ON
INFORMATION 2 ON
INFORMATION 3 ON
EXIT
Figure 13: DISPLAY INFORMATION Sub-Menu
5. Press the “Up” or “Down” button to move the cursor to
“Download Configuration” and press “Set” to execute.
Make sure a TCPIP232 Adapter is connected and the
VSI-Pro will download the IP settings to this device.
Refer to Appendix I for additional information on the
TCPIP232 Adapter or the manual included with the
adapter.
NOTE: The choices are On or OFF and selects the differ-
ent packettes of information printed on the reciept to your
selection.
TCP/IP Limitations
The TCPIP232 Adapter can monitor any Ethernet LAN
either 10MBs or 100MB/s. However the actual long term
throughput of the adpater is limited to 5MB/s. This is more
than enough for network printers for cash receipts, bar
code scanners or single cash registers that operate in a
“Live Mode”. Live Mode means the register transmitts the
data on the network line by line or at the end of each
transaction.
PROGRAMMING