User's Manual

Avaya Branch Gateway Manager 10.0 Page 245
15-601011 Issue 29r (Friday, November 02, 2012)B5800 Branch Gateway
Configuration Settings: Line
5.4.11.4 SIP URI
Having setup the SIP trunk to the SIP ITSP, the SIP URI's registered with that ITSP are entered on this tab. A SIP URI
(Uniform Resource Identifier) is similar to an internet email address, for example [e-mail], or
[e-mail] and represents the source or destination for SIP connection. The URI consists of two parts,
the user part (eg. name) and the host part (eg. example.com).
· If the wildcard * is used in the SIP trunk's Local URI, Contact and Display fields, that SIP trunk will accept any
incoming SIP call. The incoming call routing is still performed by the system incoming call routes based on
matching the values received with the call or the URI's incoming group setting. For outgoing calls using this SIP
URI, all valid short code CLI manipulations are used (transforming calling party number to ISDN will be ignored).
For the system, each SIP URI acts as a set of trunk channels. Outgoing calls can then be routed to the required URI by
short codes that match that URI's Outgoing Group setting. Incoming calls can be routed by incoming call routes that
match the URI's Incoming Group setting.
Note that the system only supports up to 150 URI records on a SIP line.
Usability
· Mergeable: These settings are not mergeable. Changes to these settings will require a reboot of the system.
Configuration Settings
· Via
This field is for information only and cannot be edited. It shows the IP address of the system LAN interface with which
the SIP trunk is associated.
· Local URI: Default = Use Authentication Name
This field sets the 'From' field for outgoing SIP calls using this URI. The value can either be entered manually or one of
the following options can be selected.
· Use Credentials User Name
Use the User Name from the SIP Credentials record being used for the call.
· Use Internal Data
Use the SIP Name value from the User | SIP tab of the user making the call. The system can also use SIP URI
information configured for a hunt group (Hunt Group | SIP ) or for the voicemail (System | Voicemail ).
· Use Credentials Authentication Name
Use the Authentication Name from the SIP Credentials record being used for the call.
· Use Credentials Contact
Use the Contact information from the SIP Credentials record being used for the call.
· Contact: Default = Use Authentication Name
This field sets the 'Contact' field for SIP calls using this URI. The value can either be entered manually or one of the
following options can be selected.
· Use Credentials User Name
Use the User Name from the SIP Credentials record being used for the call.
· Use Internal Data
Use the SIP Name value from the User | SIP tab of the user making the call. The system can also use SIP URI
information configured for a hunt group (Hunt Group | SIP ) or for the voicemail (System | Voicemail ).
· Use Credentials Authentication Name
Use the Authentication Name from the SIP Credentials record being used for the call.
· Use Credentials Contact
Use the Contact information from the SIP Credentials record being used for the call.
· Display Name: Default = Use Authentication Name
This field sets the 'Name' value for SIP calls using this URI. The value can either be entered manually or one of the
following options can be selected.
· Use Credentials User Name
Use the User Name from the SIP Credentials record being used for the call.
· Use Internal Data
Use the SIP Name value from the User | SIP tab of the user making the call. The system can also use SIP URI
information configured for a hunt group (Hunt Group | SIP ) or for the voicemail (System | Voicemail ).
· Use Credentials Authentication Name
Use the Authentication Name from the SIP Credentials record being used for the call.
· Use Credentials Contact
Use the Contact information from the SIP Credentials record being used for the call.
250
306
328 155
250
250
250
306
328 155
250
250
250
306
328 155
250
250