User's Manual

Avaya Branch Gateway Manager 10.0 Page 143
15-601011 Issue 29r (Friday, November 02, 2012)B5800 Branch Gateway
Configuration Settings: System
· Time Offset: Default = 00:00
This value is not normally set as any time changes, including daylight saving changes, that occur on the
PC will be matched by the system.
· If you are running Branch Gateway Manager when the voicemail server starts, voicemail does not start as a
time server. It is therefore recommended that you have no copy of Branch Gateway Manager running when
you start or restart the voicemail server. Branch Gateway Manager can be disabled from acting as a RFC868
time server by deselecting the Enable Time Server option (File | Preferences | Edit | Preferences ).
· SNTP
Use a list of SNTP servers to obtain the UTC time. The records in the list are used one at a time in order until there
is a response. The system makes a request to the specified addresses following a reboot and every hour
afterwards.
· Time Server Address: Default = Blank
Enter a list of IP addresses or names for the SNTP servers. Separate each record with a space. The use of
broadcast addresses is not supported. The list is used in order of the records until a response is received.
· Time Zone: Default = Match to system Locale
The value is defaulted to match the system locale.
· Local Time Offset from UTC: Default = 00:00
This setting is used to set the local time difference from the UTC time value provided by an SNTP server. For
example, if the system is 5 hours behind UTC, this field should be configured with -05:00 to make the
adjustment. The time offset can be adjusted in 15 minute increments. If also using the daylight time saving
settings below, use this offset to set the non-DST local time.
· Automatic DST: Default = On
If enabled, the system will apply daylight saving time (DST) changes to the displayed local time.
· Clock Forward/Back Settings
This drop down lists the currently configured dates and times for the start and end of daylight savings when
Automatic DST above is enabled. Branch Gateway Manager initially applies up to 10 default values from the
current year based on the system locale. However, these should be checked to ensure that they match the
expected values and any recent changes to local DST requirements.
· Each of the 10 entries can be edited by selecting it in the drop-down list and then clicking Edit.
· An existing entry can be deleted by selecting it in the drop-down list and then clicking Delete.
· If less than 10 entries are setup, a new entry can be added by selecting <Add New Entry> from
the drop-down list and then clicking Edit.
· DST Offset
Set the amount by which the time should be changed when DST is applied or removed.
· Clock Forward/Back
This drop down can be used to set the paired dates for the start (go forward) and end (go back) of the
daylight saving period.
· Select Clock Forward and double clicking on the required date and set the Local Time to Go
Forward. Then select Clock Backward and double click on the required date and set the Local
Time to Go Back.
· Local Time to Go Forward
Set the time at which the DST Offset should be added to the local time when DST is started.
· Local Time to Go Back
Set the time at which the DST offset should be removed from the local time when DST is removed.
· File Writer IP Address: Default = 0.0.0.0 (Disabled)
This field set the address of the PC allowed to send files to the System SD card installed in the system using HTTP or
TFTP methods other than embedded file management. An address of 255.255.255.255 allows access from any
address. If embedded file management is used, this address is overwritten by the address of the PC using
embedded file management (unless set to 255.255.255.255).
· PLDS Host ID
The PLDS Host ID is the ID code printed on the Avaya Branch Gateway SD card and is used to validate the license file.
· AVPP IP Address: Default = 0.0.0.0 (Disabled)
Where Avaya 3600 Series SpectraLink wireless handsets are being used with the system, this field is used to specify
the IP address of the Avaya Voice Priority Processor (AVPP).
· DSS Status:
This setting has been moved to the System | Telephony | Telephony sub-tab.
· Beep on Listen: Default = On (USA)/On (Rest of World)
This setting has been moved to the System | Telephony | Tones & Music sub-tab.
· Hide auto record:
This setting has been moved to the System | Voicemail sub-tab.
100
131
159
163
155