Specifications

27
User’s, Installation and Maintenance Manual
STOP
STOP
STOP
The following prohibitions shall be observed when using the
service lift. The consequences of not following them are
extremely hazardous to the physical integrity of the users.
(If MANUAL/AUTO selector
1)
on cabin control box
is provided) After using service lift and before
exiting the WTG, the MANUAL/AUTO selector of
cabin control box shall be turned to the AUTO
position. This way it will be possible to call the lift
from top platform if necessary.
4.2 Prohibited uses
It is prohibited to:
1. Use the service lift beyond its intended purpose.
2. Operate the lift without following the safety
warnings and operating instructions.
3. Load the service lift more than its
rated load.
4. Try to repair machine components.
Only personnel from AVANTI or qualified
personnel authorised by AVANTI are
allowed to perform service on the service
lift.
5. To travel on service lift roof.
6. To use the emergency manual release
of door lift or fence doors during normal
use.
7. To manipulate switches or safeties.
8. To disattach trapped key
2)
from wire rope.
9. To have a second trapped key
2)
.
4.3 Operation from inside
the cabin
1. Turn the ON/OFF main switch of the bottom platform
control box to the ON position.
2. Open the door, climb the fence-railing and go inside
the cabin and close the door.
3. Turn the ON/OFF selector of the cabin control box to
the ON position.
4. To go up or down, press and hold the UP or DOWN
button as needed.
4.4 Operation from bottom platform
To send
3)
or call the service lift from the bottom platform
control box:
1. Check that the ready light is illuminated.
2. Check that the fault light is not illuminated.
3. Press and hold the UP
3)
or DOWN button.
Coordinate send
3)
or call actions between personnel
by means of walkie-talkies.
Transportation of persons is forbidden if the operation
is controlled from the platforms.
4.5 Operation from top platform
To send
3)
or call the service lift from the top platform
control box:
1. Check that the ready light is illuminated.
2. Check that the fault light is not illuminated.
3. Press and hold the UP or DOWN
3)
button.
4.6 Landing alignment
The service lift can be landed at any platform totally
aligned to permit safe egress and ingress. To do so:
1. Travel to desired platform (bottom, intermediates and
top one).
2. Locate the service lift so that alignment sticker of
inside the cabin overlaps alignment sticker of the ladder.
2B. If a platform switch
4)
is provided, locate service lift
so that platform light
4)
of cabin control box illuminates.
3. Exit from cabin can be done safely.
4.7 Enter and exit cabin
4.7.1 Bucket type
5)
To enter the cabin:
1. Open the door and attach the shock absorber to the
cabin anchor point.
2. Climb the fence-railing holding the handles.
3. Climb down using the cabin steps.
To exit the cabin:
1. Attach the shock absorber to the cabin anchor point
and open the door.
2. Climb up the cabin using the cabin steps and
holding the handles.
3. Climb down the fence-railing to the platform.
4.7.2 Full sliding door
2)
To enter the cabin:
1. Open the door.
2. Enter the cabin.
3. Attach the shock absorber to the cabin anchor point.
4. Close the door.
To exit the cabin:
1. Open the door.
2. Exit the cabin.
3. Release the shock absorber from the cabin anchor
point.
4. Close the door.
4.7.3 Top / Bottom hatch
To enter the cabin:
1. Climb the ladder attached to the fall protection
system or attach the shock absorber to the tower
anchor.
2. Open the hatch.
3. Attach the shock absorber to the cabin anchor point.
4. Release the fall protection device or shock absorber
from the tower anchor point to enter the cabin.
5. Climb inside the cabin holding the handles
6)
and the
cabin main frame ladder as support.
6. Close the hatch
1)
Not applicable to CE versions. Mandatory for AECO version.
2)
Optional for CE versions. Mandatory for AECO version.
3)
Optional for CE versions and for AECO version.
4)
Optional for CE bucket type version.
Mandatory for CE full sliding door version and for AECO version.
5)
Optional for CE versions. Not available for AECO version.
6)
Applicable to CE bucket type version.