Owner`s manual
2SWLRQDO(TXLSPHQW
7UDYLV,QGXVWULHV
Surround Panels (see part #'s below)
3$1(/ 6,=,1*
6L]H 6L]H RQ,QVHUWZWULP 3$57
ZLGHE\KLJK
ZLGHE\KLJK
ZLGHE\KLJK
,167$//$7,21
,16758&7,216
1. With the insert 12” from the
fireplace, install the side
surround panels (see the
directions to the right).
2. Adjust the position of the
side panels so they are: 1)
aligned with the top of the
insert; 2) both the same
distance back from the front
of the insert; 3)
perpendicular to the floor
(use the top panel, if
necessary, to judge
alignment). Tighten the
screws that hold the side
panels in place.
3. Install the top panel and trim
following the directions to
the right.
,QVXODWLRQ
,QVWDOODWLRQ
UHTXLUHG IRUIDFHVHDO
LQVWDOODWLRQV RQO\
1. With the insert drawn 6"
from the fireplace, glue the
insulation strip included with
the surround panel kit to the
back of the panels using
RTV silicon or stove gasket
cement. The insulation
should be installed so it
overlaps the fireplace
opening to form a seal
between the panels and the
fireplace face. Let the
silicon or cement dry.
2. Push the insert into the
fireplace, allowing the
insulation to form a seal
between the panels and the
fireplace. Use a screwdriver
to tuck any exposed
insulation behind the panels.
$YDORQ3HQGOHWRQDQG5DLQLHU
5HPRYHWKHEUDVVWULPDORQJWKHWRSRIWKHVWRYH
%XWWRQ3OXJV
SU\RXWZLWKDVFUHZGULYHU
6LGH
3DQHO
1XWGULYHU
$WWDFKWKHVLGHSDQHOVZLWK
WKHLQFOXGHGVFUHZV
KLQW
SUHWKUHDGWKHKROHVSULRU
WRLQVWDOOLQJWKHSDQHOV
/%UDFNHW
5LJKW6LGH
7ULP
7RS7ULP
2SWLRQDO7ULP,QVWDOODWLRQ
,QVHUWRQHOHJRIHDFK/EUDFNHWLQWRWKHWRS
DQGVLGHWULPSLHFH$OLJQWKHWULPWRIRUPD
SUHFLVHFRUQHUWKHQWLJKWHQWKHWZRVHW
VFUHZVZLWKDVPDOOVWDQGDUGVFUHZGULYHU
6OLGHWKHWULPRYHUWKHSDQHOV3ODFHWKH
VSULQJFOLSVEHKLQGWKHSDQHOVDWWKHORFDWLRQV
VKRZQ7KLVNHHSVWKHWULPWLJKWDJDLQVWWKH
SDQHO
0LFUR´
6WDQGDUG
6FUHZGULYHU
,QVWDOOWKHWRSSDQHOVRWKHWDEVLQVHUW
LQWRWKHMRJJOHFOLSVRQWKHWRSSDQHO
7RS
3DQHO
6SULQJ
&OLSV
7RS7ULP
2SWLRQDO.QRFN2XW
$QRSWLRQDONQRFNRXWLVSURYLGHGRQERWK
VLGHVLIWKHSRZHUFRUGLVURXWHGEHKLQGWKH
VXUURXQGSDQHO
1XWGULYHU










