Installation manual

ManualsBrandsAvalon ManualsKitchen AppliancesEden Green Smart

GreenSmart™ Remote (2010 Version)

SKU 99300685 (NG) SKU 99300684 (LP)

Page 1 of 14 4/14/11 - 17601643 © Travis Industries, Inc.

Overview

This wiring harness attaches to the existing wire harness (unlike the older version).

DO NOT REMOVE THE EXISTING WIRE HARNESS ON YOUR APPLIANCE.

New Wiring Harness

This kit includes a revised remote wiring harness that is smaller and easier to install than the old wiring

harness (see diagram below). The instructions included with this kit should be followed first

. Then the

instructions included in the installation manual should be followed, omitting the steps pertaining to wire-

harness installation. This wiring harness works on all GreenSmart™ compatible appliances.

Order of Installation

STEP # 1 Install the Wiring Harness and Receiver (see pages 4 through 6).

STEP #2 Install the remaining components for the remote following the instructions

included in the manual* (Stepper Motor, Fan Control Module, etc.).

STEP # 3 Replace the control panel and restore appliance to the correct configuration.

* Because each appliance has different installation parameters, additional installation instructions are

included in the manual shipped with the appliance (manuals may also be found at travisproducts.com).

VALVE

IPI / CPI

STEPPER MOTOR

BURNER CONTROL

RECEIVER

FAN CONTROL

STEPPER MOTOR

FAN CONTROL

POWER SUPPLY

ON / OFF

New Wiring Harness Old Wiring Harness

Summary of content (14 pages)

PAGE 1
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Overview This wiring harness attaches to the existing wire harness (unlike the older version). DO NOT REMOVE THE EXISTING WIRE HARNESS ON YOUR APPLIANCE. New Wiring Harness This kit includes a revised remote wiring harness that is smaller and easier to install than the old wiring harness (see diagram below). The instructions included with this kit should be followed first.
PAGE 2
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Compatibility The GreenSmart™ remote is compatible with all of the new Travis GreenSmart products.
PAGE 3
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Installation When installing the remote, refer to the wiring diagram shown below.
PAGE 4
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Installation (continued) 1 Remove the control panel on the appliance to allow access to the wiring (see installation manual). 2 Disconnect the comfort control connector. 3 Remove the on/off/battery plate from the appliance. 4 Carefully disconnect the on/off wires from the on/off switch. WARNING: Do not pull on the wires while disconnecting.
PAGE 5
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Installation (continued) 5 Carefully disconnect the power supply wires from the ac adapter. The ac adapter may be discarded. WARNING: Do not pull on the wires while disconnecting. Grasp the both quick-connects while disconnecting. 6 Cut the two wires leading to the comfort control switch on the on/off/battery plate. The on/off/battery plate may be discarded. On newer appliances this connection has quick connects.
PAGE 6
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Installation (continued) 8 Attach the new wiring harness to the on/off switch and power supply wires. Attach corresponding wires to the same color (red to red, white to white, etc.). Wiring Harness on Appliance New Remote Wiring Harness 9 Attach the wiring harness to the receiver. Install the remote receiver into the control panel.
PAGE 7
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Battery Installation Transmitter Battery Installation Install the three included AAA batteries into the remote (see Figure 1). °F ery att AB AA ery att AB AA A AA ry tte Ba Figure 1 Receiver Battery Installation Install four AA batteries into the receiver (see Figure 2). You can use the batteries from the battery backup tray on the appliance. See the installation instructions for details.
PAGE 8
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Set-Up Verify the Fan Control Module is On The fan control module has a power switch. Make sure it is in the ON (“-“) position (see Figure 3). This switch must remain in the ON position for the AC components to operate (Accent Light and Optional Blower). The module also supplies low-voltage for the fireplace controller.
PAGE 9
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Direct Fireplace Operation The fireplace may be directly operated from the receiver. The three positions are below (see Figure 5): ON – Fireplace burner turns on (regardless of transmitter settings). OFF – Fireplace burner turns off (regardless of transmitter settings). REMOTE – Fireplace is controlled by the transmitter.
PAGE 10
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Remote Operation Once the receiver is switched to “REMOTE” the transmitter operates the fireplace. Once you understand how the transmitter works, you will be able to operate your fireplace quickly and easily. Display Overview The transmitter display has four main sections (see Figure 6). Thermostat Display Room Temperature Display F ON Read-Out (Thermostat Setting, Function, etc.
PAGE 11
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Manual On-Off / Smart Thermostat / Standard Thermostat Use the thermostat button to cycle through the three thermostat settings (see Figure 8). Look here for the Press the thermostat button to cycle thermostat setting. through the thermostat settings. F OFF ON ON MAX SMART AUX Figure 8 MANUAL ON/OFF – The burner will turn on and off using the remote (see Figure 9). Press the On/Off button to control the burner.
PAGE 12
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Mode Controls (Flame, Blower, Light, Comfort Control) Use the mode button to cycle through the four mode controls (see Figure 12 below). Press the mode button to cycle through the mode settings. F OFF Flame Height Comfort Control Optional Blower Accent Light Look here for mode controls.
PAGE 13
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Mode Controls (continued) Accent Light (Aux) The Accent Light (night light) inside the heater may be turned on and off using the up and down buttons when in Accent Light (Aux) Mode (see Figure 15). The center display will display either “ON” or “OFF”. F On OFF This is the accent light readout. Use the up button to turn When in accent light on, down button to turn off (2 mode, this icon will Off settings). appear darkened.
PAGE 14
GreenSmart™ Remote (2010 Version) SKU 99300685 (NG) SKU 99300684 (LP) Low Battery Indicator Transmitter Batteries The transmitter has a battery-level indicator. When it indicates low battery voltage (see Figure 18 below), install four new AAA alkaline batteries into the transmitter (see “Transmitter Battery Installation” on page 7). Low Battery Indicator F ON MAX AUX Figure 18 Receiver Batteries The receiver will “beep” periodically when the receiver batteries go low.