Self Cleaning Water Dispenser Bottleless Model: A5BOTTLELESS self clean
DIRECTORY 1 SAFETY PRECAUTIONS 2 GETTING STARTED TROUBLE SHOOTING 6 WATER PURIFIER 7 8 MACHINE INSTALLATION 10
A: PART NAME 10 self clean 14 15 16 8 9 17 self-cleaning switch push button of room temperature water LED night light switch reset button filter valve 14 15 16 17 NOTE: Please use the product in a place with temperature of 39-100 F and relative humidity level.
B: SAFETY PRECAUTIONS
This appliance can be used by children aged from 8 years and above if they have been given supervision or instruc on concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
3. Unpack the product, install the drip tray. 4. Take out the quick joint adapter with valve and install it on the water pipe. Intall the adapter: Adapter with Valve PE pipe (3m) Extra Filter Flushing Tape and Tools (not included) Adapter 1. Disconnect the current cold water supply line, as in figure 1. 2. Connect the adapter with valve to the cold water supply line, as in figure 2. 3. Connect the nut on the side of the metal adapter and insert the PE pipe through the nut.
3. Hold this filter with A4 System filter flushing adapter over a sink and turn on the valve near the water source. Let water to flow out of the filter and A4 System filter flushing adapter for 5 minutes to flush the new filter. 4. Shut off the valve at the water source. Finishing the Water Cooler Installa on 1. Remove the end of the PE tube from the A4 System filter flushing adapter by pressing in on the blue ring and pulling out the PE tube. 2. Twist out the filter from the A4 system filter flushing adapter. 3.
Filter replacement cycle replacement 6 Months or 1500 gallons function Reduce Chlorine, Taste and odor, Nominal particular class I, Lead and Cysts. Special hints: The data above is for reference only. It is based on normal water use. The specific cycle for replacement of filters varies with local water quality. D: TROUBLE SHOOTING No water is coming from the spout. Make sure to completely depress the push bu on controls. Cold water is not cold. It takes up to one hour a er setup to dispense cold water.
Water leakage. If the 3 lights of hea ng light, cooling light and filter light are flashing, there should be leakage. Please check the PCB on the plate. Repair the machine and dry the PCB, and then power on again. Pipe not connected properly. Inspect the adapter to connect the pipe properly. Water pipe and PE pipe burs ng. Replace the water pipe. . Please allow 15 minutes for the hot water to be heated. During this me the red indicator light will be steady.
Dispensing room temperature water 1. Posi on bo le, glass, pitcher, or cooking pot below spout. 2. Depress normal water push bu on downward to start normal water flow. 3. Release push bu on once desired fill level is achieved. A er setup, hot water will be available in 15-20 minutes. 1. Posi on bo le, glass, pitcher, or cooking pot below spout. 2. Slide red bu on away from you and depress hot water push bu on downward to start hot water flow. 3. Release push bu on once desired fill level is achieved.
3. Sani zing This machine should be sani zed with a disinfectant and then cleaned with water every three months. (See cleaning and draining instruc ons.) 4. To Remove Mineral Deposits Mix 4 L of water with 200 g of citric acid crystals, pu ng the mixture into the machine making sure the water can flow out of the hot water tap. Switch on the power and heat it for about 10 minutes. 30 minutes later, drain the liquid, then clean it with water two or three mes.
G: MACHINE INSTALLATION To prevent the machine from swaying or falling, we have included an op onal bracket. Please install the bracket accordingly. 1-2. Loosen the screw of the le or right bo om angle as in the picture below. 3. Use the screw to fix the bracket on the le or right bo om angle of the water dispenser. 4. Make a hole on the floor's surface where the water dispenser will be installed. 5. Fix the bracket on the floor by screwing ghtly. 6. Tighten the screw.
