AcceleRAID 352 Quick Installation Guide DB11-000027-00 First Edition 08P5516
Electromagnetic Compatibility Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
Declaration of Conformity Per FCC Part 2, Section 2.1077(a) Manufacturer’s Name: LSI Logic Corporation Manufacturer’s Address: North American Headquarters Milpitas, CA USA Declares that the product: Product Name: High Performance RAID Controller Model Number(s): AcceleRAID 352 Year of Manufacture: 2000 Conforms to the following Product Specification(s): FCC: CFR 47 Part 15, Subpart B, Section 15.107(e) and Section 15.109(g) Class B Digital Device tested per ANSI C63.
Declaration of Conformity Per 89\336\EEC Responsible Party Name: LSI Logic Corporation Address: North American Headquarters Milpitas, CA U.S.A. hereby declares that the product Trade Name: High Performance Caching RAID Controller Model Number(s): AcceleRAID 352 Fab. 550157-01 Rev.
Community of Europe CE mark is rated for the AceleRAID 352 as follows: CISPR 22 Radiated Emission EN55022, Generic immunity standard for the following: IEC 801-2 ESD, IEC 801-3 Radiated, and IEC 801-4 EFT/Burst Warning! This is a Class B product. In a residential environment this product may cause radio interference, in which case the user may be required to take adequate measures. Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse B.
Underwriters Laboratories Statement and Warning
Proprietary Rights Notice This document contains proprietary information of LSI Logic Corporation. The information contained herein is not to be used by or disclosed to third parties without the express written permission of an officer of LSI Logic Corporation. Any product(s) described herein is/are a licensed product of LSI Logic Corporation. Document Description Document DB11-000027-00 First Edition.
Trademark Acknowledgments LSI Logic, the LSI Logic logo, MORE, Mylex, and SANmapping are trademarks or registered trademarks of LSI Logic Corporation. All other brand and product names may be trademarks of their respective companies.
Contents Hardware Installation Introduction ........................................................................................ 1-1 Performing an Installation .................................................................. 1-1 PCI Hot Plug .............................................................................. 1-1 Connectors, Jumpers, and LEDs ............................................... 1-1 Installing the AcceleRAID 352 into the System Board ............... 1-5 What to Do Next ...........
2 AcceleRAID 352 Installation Guide
Hardware Installation Introduction The AcceleRAID 352 is a versatile PCI to a dual channel Ultra 160 SCSI, Low Voltage Differential (LVD) RAID controller. There are many possible hardware configurations. This quick installation guide assumes that the user is familiar with controller, disk drive, and RAID terminology. Performing an Installation WARNING To avoid electrical shock, do not attempt to perform this hardware installation with power on. Disconnect the system from the electrical wall outlet.
Performing an Installation CH0 CH1 CH0 CH1 Figure 1. AcceleRAID 352 Controller with Channel Connectors JP1 JP2 JP3 JP1 JP2 JP3 Figure 2. AcceleRAID 352 Default Jumper Identification (front) Table 1.
Hardware Installation FAIL LED U1 Figure 3. AcceleRAID 352 Controller with LED (front) Table 2. LED Description (front) U1 FAIL LED Manual No.
Performing an Installation SE 1 SE 0 LVD 0 LVD 1 PIN Nos. 654321 Figure 4. AcceleRAID 352 with LEDs and PIN Numbers (back) Table 3. LED Descriptions (back) SE 1 Single-ended LED, Channel 1 SE 0 Single-ended LED, Channel 0 LVD 0 LVD LED, Channel 0 LVD 1 LVD LED, Channel 1 Table 4. Six-Pin Header Identification (JP3) 4 Pin 1 3.
Hardware Installation Installing the AcceleRAID 352 into the System Board 1. With the power off, plug the AcceleRAID 352 controller into an available 32-bit or 64-bit PCI slot on the system board (refer to Figure 5). The 32-bit slot is short, the 64-bit slot is longer. Figure 5. Plugging the AcceleRAID 352 into a PCI Slot 2. Set the SCSI ID on each internal drive to a unique address between 0 and 15, but do not use address 7, as it is reserved for the controller.
Performing an Installation 5. Set the SCSI ID for each external disk drive to a unique address between 0 and 15, but do not use 7 (reserved for the controller). Do not duplicate SCSI IDs used by internal drives designated for the same channel. For more information on how to set SCSI IDs, refer to the disk drive documentation. If you are using an external SCSI cabinet, see the Caution note above. Figure 6. Connecting Internal and External Drives 6.
Hardware Installation ☛ Note The AcceleRAID 352 terminator is ON by default. It is automatically terminated and will be disabled automatically if necessary. An example of a typical, completed installation of the AcceleRAID 352 is shown in Figure 7. T T System Board Figure 7. AcceleRAID 352 in a Typical Installation and SCSI Connectors The hardware portion of the installation is complete. Please see the following section titled “What to Do Next”. What to Do Next 1.
What to Do Next 8 AcceleRAID 352 Quick Installation Guide
LSI LOGIC CORPORATION SOFTWARE LICENSE AND WARRANTY POLICY Limited Warranty LSI warrants to the original purchaser of the product enclosed herein (“Customer”) that (a) for a period of three (3) years from the date of Customer’s purchase of the Product (excluding batteries and memory) (the “Product Warranty Period”), and (b) for a period of one (1) year from the date of purchase of the Product by Customer (the “Battery/Memory Warranty Period”), the batteries and memory included in the Product will (i) be fre
with LSI’s instructions and the terms of this Agreement, shipping costs to be borne by LSI, and (c) Customer has provided proof of purchase price and date for unregistered Product. LSI shall bear one-way shipping, packing and insurance costs and all other costs, excluding labor and parts, necessary to effectuate repair or replacement under this warranty. All Product repaired or replaced under this warranty shall be returned to Customer at Customer’s expense.
is a part of the Product (“LSI Software”) solely as part of the Product incorporated into the OEM Products that and not on a standalone basis.
Manual No. DB11-000027-00 08P5516 LSI Logic Corporation North American Headquarters Milpitas, CA 408.433.
