Specifications

ManualsBrandsAV-GAD ManualsHome building and DecorAV-705

AV-705, 706, 707/B LCD Keypad

INSTALLATION INSTRUCTIONS V3.04A

The AV-7075, AV-706 and AV-707 EasyKey™ are the future-generation keypads, with the

AV-707 New Look shape, fully-customized microprocessor remote station, multitasks

functions with 32 Keypad ID’s, comply with year 2000 requirements. The AV-706 is an

economic version LCD keypad, with same operations and electrical specifications as AV-707.

The AV-707, AV-707B and AV-706 are compatible with EasyLoader™ “PRO” suffix alarm

control panels: AV-2004/48DPRO, AV-2008/2016 Dublo. The DPRO and Dublo (Generation

III panels) types are an enhanced version of Series 2000 panels.

Before attempting to use the AV-705, AV-707 and AV-706, read thoroughly this manual and

the control panel manual (series 2000) large version

installation manual.

Two rows, each of 16 characters display, provide full information and clear status of the

system. The keypad include simple and easy text editor for fast words writing.

Built-in standard-words and key-letters index for fast and easy custom programming in almost

any language.

Function keys, displayed upon request, facilitate setting and resetting, programmable constant

messages (e.g. time of day, service information, etc.), available in Latin or Hebrew characters.

Verify that your keypad/s version is same as panel version or higher

Ordering Information:

AV-707E:

English text keypad. AV-707ETP: English text keypad with added Tamper.

AV-707B:

English text keypad with three function buttons (fit panels Ver. 2.16 and later).

AV-706E

: English text keypad. AV-706ETP: English text keypad with added Tamper.

AV-705:

Remote keypad without LCD display (as AV-707) fits PRO & Dublo panels.

1. Wiring the AV-707, AV-706 and AV-705

AV-2004/48DPRO, AV-2008D Dublo supports up to four AV-707/706 keypads,

AV-2016 Dublo control panel supports up to eight keypads. AV-707B is compatible

with alarm panels starting version 2.16. When using four keypad or more add power

supply (like AV-21) to prevent loading the panel’s power supply.

To connect more keypads to the same system, add an external power supply (AV-

21). Wire length for each AV-707/706 Keypad should not exceed 200 meters, when

using 0.5 mm

wires. In few keypads system, wire all keypads in parallel.

+12V -12V Zone 8

OR YEL

+12V -12V

YEL OR

*TMP

AV-706/7 keypad

Panel

* The TMP terminal is available with AV-707TP

YEL

PRO Control

Item: 4710 Figure 1: Keypad wiring

Summary of content (12 pages)

PAGE 1
AV-705, 706, 707/B LCD Keypad INSTALLATION INSTRUCTIONS V3.04A The AV-7075, AV-706 and AV-707 EasyKey™ are the future-generation keypads, with the AV-707 New Look shape, fully-customized microprocessor remote station, multitasks functions with 32 Keypad ID’s, comply with year 2000 requirements. The AV-706 is an economic version LCD keypad, with same operations and electrical specifications as AV-707.
PAGE 2
IMPORTANT!! Do not connect keypad to control panel with power on. Never run Keypad wires alongside telephone wires, high voltage wires, or transmitting antennae. Keypad wires should be wired separately and not in the same cable with other devices (telephone, PIRs etc.) Do not use the keypad as junction box for wiring power to sensors. Install the keypad at human eyes height (150-180 cm) for clear display visibility 2.
PAGE 3
For cost saving application, as 2nd keypad use the AV-705. The AV-705 has the same functions as AV-707, however, the LCD display is not included. Upon power-up “Set Panel Time” is displayed, hold-down key ‘0’ then hold-down key ‘1’, enter time in 24H format and #. To set date hold-down key ‘0’ then holddown key ‘2’, enter date in dd-mm-yy format and #. The '#' is mostly used as an ENTER key, typed at the end of a command.
PAGE 4
During all kind of programming, keys displayed as they are typed (there are some combination exceptions). If after a command no key is pressed for 3 seconds, an automatic Enter generated by the keypad, thus ending the command. To speed up the procedures, the user can type '#' as Enter and send the command to the control panel. Use Enter after the "Hold Down" functions, to speed up function. To cancel the input string Hold Down key '9' (reset). Exception to the above is the zone bypass.
PAGE 5
Installer programming mode To enter Installer Programming Mode "Hold Down" key '8' (program). The three Rightmost LEDs will start blinking. Type the default Installer Code - 1 9 9 4 and ‘#’. The upper line will display 'Installer Programming', the lower line will be cleared and a blinking cursor will appear. The Leftmost two LEDs will start blinking indicating that a "location" is expected. In programming mode, locations are three digits long. The programmable locations described in the Installer Manual.
PAGE 6
Restoring the factory default zone descriptions and LOGO texts: The zone descriptions, as well as the installer LOGO displayed by the LCD Keypad are editable (refer to chapter 8) by the installer. Texts saved at the control panel and in the non-volatile LCD Keypad memory. To restore zone description and Logo texts to their factory default, type 200 then 70.
PAGE 7
6. Setting the Keypad ID When several keypads connected to the control panel, the LCD Keypads better have ID (Identification) numbers. During installation set each keypad to the required ID number, otherwise all keypads will act as number 01. By default, the ID of a new keypad is number 01. ID numbers are in the range of 1 to 32. Give these numbers arbitrarily as long as two keypads don't share the same number.
PAGE 8
The '2' and '5' keys act as UP arrow (2) and DOWN arrow (5). Keys ‘2’ and ‘5’ scroll texts and letters up and down. If we visualize a top-down list, where the first entry (1) is at the top and the last entry is at the bottom, and then the DOWN arrow will move towards the bottom (the last entry) while the UP arrow will move towards the top (the first entry). Thus, pressing repeatedly the ‘5’ - DOWN key, texts for zones 1,2,3... will be displayed.
PAGE 9
To reach the required characters range, use the '*' key. By repeatedly pressing '*' key we jump from one range of characters to another in the order: 'space', '0', 'A', 'M', 'a', 'm' and space again (starting from the current range in which the character at the cursor is now). Moreover, to change a letter case (UPPER<>LOWER) press key '8'. To insert a space at the cursor press the '6' key.
PAGE 10
Note: The AV-707 dark window and AV-706 upper Gray color panel are covered with a thin protective sheet; remove the sheet when the installation is over. 9. New Eight Programmable Timers (version 2.11 and higher) The eight timers feature is not available with all alarm panels. By enabling 074 – 2 (074-5 for version 3 and Dublo), eight programmable automatic timers are available. In EUR version (with Power-Cut hardware), the timer also can disconnect the Aux. Power (to sensors and keypad).
PAGE 11
Arming with Auto Timers Enabled Arming is performed even with open zones. Disarming with Auto Timers Enabled Follow-Me telephone number is not erased after automatic disarming. If Opening/Closing report to central station is enabled the report is always sent even if USER 1 was not selected to report. Using CID (Contact ID) format an automatic Opening Closing is reported.
PAGE 12
10. AV-707B (supported by PRO & Dublo panels version 2.16 and higher) System 3 Disarmed 12:00 * armed status shunt A fire B The AV-707B is an enhanced version with three functional buttons. Each buttons automatically enter to Home Mode A, B, or C and arms the system. Optional: Metallic versions type AV-707BG (Golden) and AV-707BS (Silver), contains the three buttons.