MANUAL C O M B O TRANSMISSION W I T H F U L L REMOTE A L A R M STARTER S Y S T E M AS-6070 TW User Guide A note concerning the battery inside the transmitter: Depending on the usage of the transmitter, the battery can last anywhere between 3 to 6 months. When the battery is low, it the transmitter will emit two beeps in a repetitive cycle. At that point you should replace your battery with a new one. That is why we recommend that you keep a spare battery somewhere handy such as the glove compartment.
Table of Contents Table of Contents ................................... 2 Transmitter Part Number and Serial Number of the Remote Car Starter Module.................................................... 3 Introduction............................................. 3 Using the Remote Control ...................... 3 LCD Remote Functions .......................... 4 Basic Vehicle Operation ......................... 4 Alarm Clock ............................................ 4 Time Adjust Mode......................
Transmitter Part Number and Serial Number of the Remote Car Starter Module The boxes below contain information concerning your transmitter and Remote Car Starter. We entered the part number of your transmitter for you. Should you need to order a new transmitter, you will need to provide the transmitter part number which is printed below. The second box contains the serial number of the Remote Car Starter. Please make sure that the installer has entered the serial number in that box.
The functions of the transmitter are as follows: LCD Remote Functions The Transmitter offers several command-confirmation and timer features. This section explains some of the key functions available on the Remote Control. Next section gives a summary of the button combinations used to access the functions (see LCD Remote Operation Tables).
Countdown Timer This feature allows set up a countdown of a duration entered by the user in hours and minutes using the button (refer to the tables). Parking Countdown This version of the Countdown feature is particularly useful for keeping track of parking meter time: the user may quickly set up the countdown in slices of 10 or 30 minutes using and buttons (refer to the tables).
will start flashing on the display. This will go on until either the Lock ( ) or the Unlock ( ) button is pressed on the remote control. LCD Transmitter Operation (First Car Control) Basic Vehicle Operation FUNCTION BUTTON PRESSED ICON BUZZER INSTRUCTIONS /DESCRIPTION LOCK 1 Beep UNLOCK 2 Beep TRUNK or AUX 3 START * (see Runtime Options below) STOP 1 Beep Locks the doors and arms the Starter Kill (if installed) and the alarm.
Cold Weather Mode FUNCTION BUTTON PRESSED TO ENTER COLD WEATHER MODE TO EXIT COLD WEATHER MODE ICON None TO ENTER COLD WEATHER MODE IN SAFE START MODE X2 TO EXIT COLD WEATHER MODE IN SAFE START MODE X2 None BUZZER INSTRUCTIONS /DESCRIPTION Melody Press and hold for 3 seconds. Melody Press and hold for 3 seconds Melody Press twice within 3 seconds. Or: press and hold for 1 second (melody) then press and hold for 3 seconds. Melody Press twice within 3 seconds.
Safe Start Mode FUNCTION BY PRESSING START ON SAFE START MODE X2 STOP ON SAFE START MODE ICON + None BUZZER INSTRUCTIONS / DESCRIPTION Melody Press the button twice within 3 seconds. Or: Press for 1 second (melody) then press again for 1 second.
To set the system to Ready Mode: 1. Ensure that all the doors are closed and that the shifter is in the neutral position. 2. With the engine already running, apply the parking brake and release the brake pedal. Make sure to release the brake pedal. 3. Within 20 sec. press LOCK, UNLOCK or START/STOP on the transmitter. The parking lights will flash 3 times quickly and remain lit. 4. Remove the key: the engine will go on running. 5. Exit the vehicle and close the door. 6. Press and hold either: a.
of vehicles could cause them to remain ON even after remote starter shut down, resulting in a dead battery. Driving Off With the vehicle running under remote control, press the UNLOCK button to disarm and unlock the doors. Enter the vehicle and do the following: x Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK position while the engine is running. This would cause the starter motor to re-engage.) x Press the brake pedal to disengage the remote starter unit.
Caution!!! Do not leave children or pets unattended in a vehicle standing in Idle Mode. Turbo Mode If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after the user leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it is shut down by remote control), then shut down the engine and set the System to Ready Mode. To activate Turbo Mode, follow all steps of the Ready Mode routine: 1.
x Come ON, go OUT; then x Flash twice. “Home ValetTM” Mode If configured at installation, this feature will remotely set the vehicle to a no-remote-start mode: if the vehicle is parked indoors there is no danger of it starting accidentally by remote control. Note: Once the Home Valet Mode is activated, the vehicle will not start by remote. To take the system i n t o Home Valet Mode: x Press the LOCK or UNLOCK button. x Within 5 seconds, press the Lock and START/STOP button simultaneously.
Note: To stop Panic Mode before the end of its delay, press the LOCK or UNLOCK button until the sound signal stops. Quick LockoutTM (Also called Secure Panic.) For fast protection in emergency situations, the system will LOCK all doors when you press the brake pedal while you hear the sound signal. (Quick Lockout is only available when Panic Mode has been set off.
Priority Door Access (Enabled by default.) If the Remote Door Locks option is installed on your vehicle, this safety feature allows you unlock solely the driver’s door with a single press of the UNLOCK button on the transmitter; upon a second press of the UNLOCK button, all the other doors will unlock. Active or Passive Arming (Passive Mode by default.
Car Finder (Enabled by default.) When enabled, the Car Finder option will help you locate your vehicle by generating a pulsating signal through the horn or the siren. To hear the signal, press the LOCK and UNLOCK buttons simultaneously. This will cause a pulsating signal lasting for the time you keep the buttons pressed. Siren or Horn Chirp Timing The duration of the chirps can be adjusted at installation (from 5 to 200 ms). Safe Start (Disabled by default.
Multi-car Operation This option allows the owner of two vehicles, both equipped with System systems, to control both systems with a single remote control. To control the second vehicle, simultaneously press the TRUNK button and the button of the function you wish to use. See the transmitter operation table earlier in this Guide. for full instructions on second car operation. Note: Your remote control must be configured for second car operation by the installer. L.E.D.
