AUTOMATIC TRANSMISSION REMOTE STARTER AS-2510 TW User Guide A note concerning the battery inside the transmitter: Depending on the usage of the transmitter, the battery can last anywhere between 3 to 6 months. When the battery is low, it the transmitter will emit two beeps in a repetitive cycle. At that point you should replace your battery with a new one. That is why we recommend that you keep a spare battery somewhere handy such as the glove compartment. DOC.1.
Table of Contents Table of Contents ................................... 2 Transmitter Part Number and Serial Number of the Remote Car Starter Module.................................................... 3 Introduction............................................. 3 Using the Remote Control ...................... 3 LCD Remote Functions .......................... 4 Basic Vehicle Operation ......................... 4 Alarm Clock ............................................ 4 Time Adjust Mode......................
Transmitter Part Number and Serial Number of the Remote Car Starter Module The boxes below contain information concerning your transmitter and Remote Car Starter. We entered the part number of your transmitter for you. Should you need to order a new transmitter, you will need to provide the transmitter part number which is printed below. The second box contains the serial number of the Remote Car Starter. Please make sure that the installer has entered the serial number in that box.
LCD Remote Functions The Transmitter offers several command-confirmation and timer features. This section explains some of the key functions available on the Remote Control. Next section gives a summary of the button combinations used to access the functions (see LCD Remote Operation Tables). Note: If you wish to exit a function while still in the process of accessing it, simply stop and wait for at least 10 seconds: the Remote Control will return to its normal state.
Parking Countdown This version of the Countdown feature is particularly useful for keeping track of parking meter time: the user may quickly set up the countdown in slices of 10 or 30 minutes using and buttons (refer to the tables). the Melody Selection The Remote Control allows the user to select which melodies are to be used upon the following events: remote starting of the vehicle, the Alarm, ending of the countdown, entering Cold Weather Mode.
Transmitter Mode Selection FUNCTION BUTTON PRESSED POWER-SAVING MODE + ( + ICON BUZZER ) MELODY INSTRUCTIONS /DESCRIPTION Press UNLOCK first and then press the Function button and the Lock button simultaneously.
Home ValetTM FUNCTION BY PRESSING Step 1 : or Step 2 : + TO ENTER HOME VALET™ MODE ICON BUZZER or Press Within 5 seconds, 1 BEEP Simultaneously within 5 sec. TO EXIT HOME VALET ™ MODE NONE INSTRUCTIONS / DESCRIPTION NONE NONE press + : the Transmitter will display and you will hear 1 beep. INSERT KEY IN INGNITION SWITCH AND TURN TO THE ON POSITION. THE ICON WILL DISAPPEAR.
LCD Transmitter Operation and Confirmations (Second Car Control) Basic Operations FUNCTION BUTTON PRESS LOCK UNLOCK + + + DESCRIPTION 2 Beep + STOP BUZZER 1 Beep + START TRUNK ICON + None MELODY TRUNK on vehicle will pop up BEEP + MELODY Start/Stop While in Safe Start Mode FUNCTION START ON SAFE START MODE STOP ON SAFE START MODE BUTTON PRESS + X2 + ICON + None BUZZER MELODY DESCRIPTION Press + simultaneously twice within 3 seconds.
Windshield Wipers & Radio & Headlights Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become energized while running under remote start. When leaving the vehicle you must ensure that the windshield wiper and headlight switches are OFF. Leaving the headlight switch ON on certain types of vehicles could cause them to remain ON even after remote starter shut down, resulting in a dead battery.
1. 2. 3. With the engine already running, press the LOCK button on the transmitter until the parking lights come ON. Remove the ignition key from the ignition switch. The engine will go on running. Exit the vehicle and close the door. Press the TRUNK button to lock the doors; the engine will shut down after 60 seconds of Turbo Mode. Valet Mode with the Valet Switch When your vehicle is in Valet Mode, the remote starter functionalities are disabled.
Remote Valet Mode This feature will allow you to remotely put your system into Valet Mode by using the transmitter instead of the Valet button as above. Getting i n t o Valet Mode x Hold the UNLOCK and START/STOP buttons simultaneously for 3 seconds. x The Parking Lights will flash 3 times. The Transmitter will BEEP once and will display the icon; the LED will remain on solid. Getting o u t of Valet Mode x Hold the UNLOCK and START/STOP buttons simultaneously for 3 seconds.
When the vehicle exits Cold Weather Mode, the Parking Lights will flash once. If Safe Start is enabled, you can activate Cold Weather Mode by x Pressing and releasing the START/STOP button, then x Pressing and holding the START/STOP button until the Parking Lights flash 3 times To verify whether the system is in Cold Weather Mode: x Press and release the brake pedal: If the vehicle is in Cold Weather Mode, the parking lights will stay on while the pedal is pressed.
Horn Chirp Timing The duration of the chirps can be adjusted at installation (from 5 to 200 ms). Flashing LED The user may decide to turn on or off LED flashing at any moment. To do so, simultaneously press the TRUNK and LOCK buttons on the transmitter: x Flashing LED ON: the L.E.D. will flash at all times (either under active arming or under passive arming) to indicate that the Starter Kill is active. x Active Arming: the LED will flash normally.
Remote Trunk Release If your system was installed with the Remote Trunk Release option, you can open your trunk by pressing the TRUNK button for 3 seconds on the remote transmitter or by pressing the TRUNK button TWICE within 3 seconds. Engine Run Time If you have a gas engine, your Remote Car Starter can be programmed to run the engine for 4, 15, or 25 minutes (15 minutes by default).
