Installation guide

5
will flash once for mode 1 and twice for mode
2.
After you have entered into one of the two
programming menus you can release the brake
pedal. The unit will stay in programming mode
until the hood pinswitch is pressed or the Valet
switch has been turned OFF. (So take your time to
make the proper selection)
The menu will automatically start you at function
one, once you choose from one of the three
Options; you will automatically jump to the next
function.
To select one of the three options press the
appropriate transmitter button. (See below)
1. LOCK = Option 1
2. START = Option 2
3. TRUNK = Option 3
Once an option has been selected the parking lights
will flash 1,2 or 3 times. (Depending on option
selected)
MODE 1
Function 1: Ignition Lock, Door lock/unlock
Toggled, Dual Lock Pulses
• Option 1* Ignition Lock Enabled
• Option 2 Ignition Lock Disabled
• Option 3 Ignition Lock Disabled
& Secure Lock enabled
Note: Secure lock adds a lock pulse 4 seconds after
the module starts the engine and also 4 seconds
after it stops the engine.
Function 2: Must Select default setting.
• Option 1* Enabled
• Option 2 Enabled
Function 3: Arming/disarming Chirp
• Option 1* Chirp Enabled
• Option 2 Chirp Disabled
Function 4: Passive/Active Arming
• Option 1* Passive Arming
• Option 2 Active Arming
Function 5: Door Lock Pulse Time
• Option 1* ¾second Lock/Unlock
pulse
• Option 2 4 second Lock/Unlock pulses
• Option 3 3/4second Lock pulse,
and two 1/4second
Unlock pulses.
Function 6: Siren / OEM Horn Mode
• Option 1* SirenMode Enabled
• Option 2 SirenMode Enabled
• Option 3 OEM Horn Mode
* = Factory Default
This conclude Mode 1 programming. To get a
playback of these options, press and release the
hood switch. The programming of these four
functions (and those from Mode 2) will play back
in sequence via the parking lights.
MODE 2
This mode allows you to customize the
alarm/remote starter's control of crank cycles,
engine run time and diesel engine options.
Function 1: Engine Run Time
• Option 1 4 minutes
• Option 2* 15 minutes
• Option 3 25 minutes
Function 2: Crank Cycles
• Option 1 2 max.
• Option 2* 3 max.
• Option 3 4 max.
Function 3: Crank Time
• Option 1 6 seconds max.
• Option 2* 8 seconds max.
• Option 3 12 seconds max.
Function 4: Not Used
• Option 2* Disabled
Function 5: Engine Type
• Option 1 Gasoline Engine
• Option 2* Gasoline Engine
• Option 3 Diesel Engine
* = Factory Default
TACH WATCH LOCKOUT
Tach Watch lockout is a safety feature built into
the remote starter to protect the vehicle’s starter
motor. If, during remote start, the vehicle’s
engine ever cranks the entire programmed crank
time without detecting any tach pulses during the
first crank cycle, the unit will go into tach watch
lockout. The diagnostics for this is 3 quick
parking light flashes when trying to remote start
the vehicle.
If your module is in Tach Watch Lockout it is
indicating that a problem exists with the tach
signal it is receiving. Verify that the tach wire
from the remote starter is properly connected to a
good tach signal in the vehicle.
To remove the unit from Tach Watch Lockout
you must do the following:
1. Close the hood
2. Disable starter kill (if installed)
3. Start the engine using the key.
4. Let it run for at least 25 seconds, then shut it
off.
5. The module should now be out of Tach
Watch Lockout.