Operating instructions

3-15
SYMPTOM
• possible solution:
No power
• ensure that the ON/OFF button is on: the set is in standby
mode, press any key to activate it
• ensure that the mains cable is plugged in correctly
• switch the set OFF and then immediately back ON
Auto track does not work
• check if auto track is selected
• check if there are 2.7 seconds silence in between the tracks
(analog recording only)
• check if the source is a consumer source with the digital
output according to the IEC audio standard
• source is DVD player (no track information)
No sound
• check the audio connections
• if using an amplifier, try using a different source
Amplifier sound is distorted
• check that the analog output of the set is not connected to
the amplifier Phono input
Play will not start
• ensure that the label of the CD is facing up
• clean the disc
• check that the disc is not defective by trying another disc
Remote control does not work
• point the remote control directly at the set
• check the batteries and replace if necessary
• select the right source first
DISC RECOVER indication
• a power failure has occurred during recording, the CD
recorder is attempting to repair the disc
• if DISC ERROR then appears on the display, the disc
cannot be recorded further, and cannot be finalised. But it
can still be played on the CD recorder or another CD
recorder.
• on a CDRW disc, the track being recorded is lost, but
further recording and finalisation can still be done
INSERT DISC indication
• replace or clean the disc
• insert a CD(RW), label upwards
• wait until the lens has cleared
USE AUDIO CD indication
• insert a digital audio disc marked with “Digital audio” and
the special logo
CHECK INPUT indication
• select the correct input
• make sure the connection cable is properly connected
Will not record
• clean the disc
• check if CDR(W) is an unfinalised disc
• check that the disc is recordable and replace if necessary
• the disc is not an AUDIO disc (WRONG DISC)
• wrong input source chosen. Input label flashing (CHECK
INPUT)
• text memory full (MEMORY FULL / FINALIZE CD).
When a CDRW has to be unfinalised for recording. Erase
text for other disc(s) or finalise other disc(s) to obtain
memory space
Recording is distorted
• make sure the recording level is correct
20 second pause between recordings
• see “Recording with automatic synchronized start“.
Set does not react
• switch the set OFF and then immediately back ON
Recorded disc does not play in other standard CD
player
• finalize the CDR(W)
• insert the CDRW in a CDRW compatible player
TROUBLESHOOTING
33
English
WARNING
Under no circumstances should you try to repair the
set yourself as this will invalidate the guarantee. Do
not open the set as there is a risk of electric shock.
If a fault occurs, first check the points listed, before taking
the set for repair.
If you are unable to solve a problem by following these hints,
consult your dealer or service centre.
LASER SAFETY
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to service
this device, due to possible eye injury.
You can create a “track” by marking a passage of music
within one track on the current disc. This new “track” can be
used for recording or playing. The minimum track length is 4
seconds.
1 Press TRACK EDIT on the set.
➜ TRACK EDIT starts blinking, TRACK and the current track
number ? are displayed. The current track number is also
blinking in the track bar.
2 Rotate ¡ JOG CONTROL ™ until the desired track number
is displayed.
3 Press YES to confirm the selected track.
➜ The marker position A and the track time will be
displayed. The first 4 seconds of the track will be played
continously.
4 Press PLAY/PAUSE 2;on the set to play to the desired
start position of your new “track” (the initial position of
marker A is always the start of the chosen track).
•To fast forward to the desired start position press 5 or 6
on the set.
•To fine tune the position press first PLAY/PAUSE 2;on the
set, then rotate ¡ JOG CONTROL ™.
5 Press YES to confirm the position of marker A.
➜ The marker position B and the new “track” time will be
displayed. The first 4 seconds before marker position B
until marker position B will be played continously.
6 Press PLAY/PAUSE 2;on the set to play to the stop
position of your new “track” (The initial position of marker B
is always the position of marker A plus 4 seconds).
7 Press YES to confirm the marked passage.
➜
TRACK EDIT is shown, A-B and the track edit time are
displayed.
•Press TRACK EDIT again to leave Track Edit mode.
➜ The new “track” will be stored.
Note: If you open the CD changer tray the edit is deleted.
Clearing the track edit
1 Press NO during stop.
➜ CLEAR A-B ? is displayed.
2 Press YES to clear the markers.
➜ The markers A-B are cleared.
TEXT TOTAL TRACK TIME TOTAL REM
STEP
DIGITAL
CD
RW
CD
RW
RECORD IN PROGRESS
REC TRACK TIME
234 56 78 9 10 11 12 13 14 15 16 17 18 19 20 +
12
OPTICAL
12
ANALOG
FINALIZE ALC
1
COMPILE CD TRACK PROG
SHUFFLE REPEAT ALL EDIT
TEXT TOTAL TRACK TIME TOTAL REM
STEP
DIGITAL
CD
RW
CD
RW
COMPILE CD TRACK PROG
RECORD IN PROGRESS
SHUFFLE REPEAT ALL EDIT
REC TRACK TIME
1 234 5678 9 10 11 12 13 14 15 16 17 18 19 20 +
12
OPTICAL
12
ANALOG
FINALIZE ALC
TEXT TOTAL TRACK TIME TOTAL REM
STEP
DIGITAL
CD
RW
CD
RW
COMPILE CD TRACK PROG
RECORD IN PROGRESS
SHUFFLE REPEAT ALL EDIT
REC TRACK TIME
1 234 5678 9 10 11 12 13 14 15 16 17 18 19 20 +
12
OPTICAL
12
ANALOG
FINALIZE ALC
TEXT TOTAL TRACK TIME TOTAL REM
STEP
DIGITAL
CD
RW
CD
RW
COMPILE CD TRACK PROGRAM
RECORD IN PROGRESS
SHUFFLE REPEAT ALL EDIT
REC TRACK TIME
1 234 5678 9 10 11 12 13 14 15 16 17 18 19 20 +
12
OPTICAL
12
ANALOG
FINALIZE ALC
CDR
AUX
C
D
C
D
C
O
M
P
IL
E
C
D
R
E
C
O
R
D
JOG CONTROL
NO
YES
R
E
C
T
Y
P
E
E
R
A
S
E
F
IN
A
L
IZ
E
R
E
C
L
E
V
E
L
B
A
L
A
N
C
E
T
E
X
T
P
R
O
G
T
R
A
C
K
E
D
I
T
C
D
T
E
X
T
E
D
IT
IN
G
Track editing (on CD changer only)
SPECIAL FEATURES
32
English
BRIEF OPERATING INSTRUCTIONS