User's Manual
Table Of Contents
- Table of Contents
- 1.0 Overview
- 2.0 Remote Control Functions:
- 3.0 Remote Control Functions for System Programming
- 3.1 Vibration Test Mode
- 3.2Phone Number/Remote Programming Mode
- 4.0 Passive Alarm Function
- 5.0 GUN ALARM FUNCTION (Optional)
- 6.0 AUTOMATIC VIBRATION SENSOR ®
- 7.0 GREEN ALARM SYSTEM
- 8.0 TWO LEVEL TELEPHONE NOTIFICATION
- 7.0 USING THE THIRD BUTTON FOR MULTI USERS
- 8.0 TURNING ON THE ENGINE VIA TELEPHONE
- 9.0 REMOTE CONTROL BY TELEPHONE
- Instruction-programming:
- The 9 instructions after the beep:
- 10.0 MONITOR LED
- 11.0 PROGRAMMING THE CAR-ALARM TELEPHONE
Telephonic Car Alarm & Remote Starter
User’s Manual
New Generation Technology - The Telephonic Car Alarm & Remote Starter - www.ngtwindsor.com
5
3. By pressing button#2onthephone for 05-1 second the alarm is turned on in ON 2 mode, provided the alarm
was off previously. (THE SAMEAS REMOTE CONTROL ON 2)
4. By pressing button#3onthephone for 05-1 second the alarm is turned on in ON 3 mode, provided the alarm
was off previously. (THE SAMEAS REMOTE CONTROL ON 3)
5. Button # 4 has no function. The alarm can’t be turned off by the telephone.
6. Button # 5 has no function
7. By pressing Button # 6 for 0.5-1 seconds we can RESET the telephones instructions (PROGRAM RESET) that
were sent by pressing button # 7, # 8, # 9. It RESETS all three at the same time.
8. By pressing Button # 7 for 0.5-1 seconds we can activate the VIBRATION SELECT ON function. The purpose of
this function is to diminish the rate of false alarms – see Section 4.0 The ordinary part of the alarm is functioning
and it cannot be influenced by the telephone.
9. By pressing Button # 8 for 05.-1 seconds we can activate the AUXILIARY ON function which can be
independently used. Through its relay we can turn on/off appliances of 25 Amperes. (AIRCONDITIONER/
HEATING) or by switching with a jumper (in the REMOTE STARTER’s box) we can prohibit the function of the
entire car in such way that it will not react to any remote control instruction. What you can achieve in this case
is being able to give the car key to someone, but the car will only start at a time permitted by you. (You may
give permission of an engine start through the telephone.)
10. By pressing Button #9 for 4-6 seconds (entering impulse) releasing it for 1 second and pressing again for 2-3
seconds you can start your vehicles engine (will be acknowledge by a short beep). Once the engine is running,
you cannot restart it.
10.0 MONITOR LED
A red LED indicates the working order, and it should be placed in a highly visible spot. It can indicate 5 functions as
follows:
• MONITOR LED will not be lit upon DISARMING for about 30..60 seconds. (The door is closed and the engine is not
running.)
• MONITOR LED is lit half dim upon DISARMING for about 30..60 seconds if the door is open. (door-contact test,
engine is not running.)
• MONITOR LED is brightly lit upon DISARMING for about 30..60 seconds: The car alarm has switched to PASSIVE
ARMING function. (The engine is not running)
• In VIBRATION TEST function the MONITOR LED is not lit, but should we hit on the car, based on the impact the
MONITOR LED will light up for 5 seconds than turns off. For a repeated impact it will light up again for 5 seconds. The
VIBRATION TEST function lasts for 2 minutes, then it goes to off. (OFF). The same 2 minutes can be used to entering
the VOICE SAMPLES, which may be attached to the telephone numbers.
• ARMING (ALARM ON 1 or ON 2, or ON 3) The MONITOR LED is blinking with a rate of 1 Hz.