INSTRUCTION MANUAL DB 5801 250W MULTI TOOL
CONTENTS Warranty 3 Introduction 4 Environmental protection 4 Description of symbols 4 Specifications 4 General safety rules 5 Additional safety rules for oscillating tools 7 Accessories 8 Unpacking 8 Know your product 8 Installing accessories 9 Installing sandpaper 10 On/off switch 10 Flush cutting a door jamb and casing for installing flooring 10 Cutting a hole in wood flooring to install a heating vent 11 Using the detail sander attachment 11 Using the scraper blade 12 M
desk will be borne by you! We will then, at our option, either repair or replace the product, or refund your money and take back the product - in accordance with our Returns Policy, a copy of which is available at www. Warranty Power Tools 1 Year Repair Warranty. Register your warranty at www.automatictools.com.au All warranty conditions can be found on the www.automatictools.com.au website or email help@globalpowerbrands.com or call 1800 909 909 1.
Introduction Description of symbols Your new AUTOMATIC power tool will more than satisfy your expectations. It has been manufactured under stringent AUTOMATIC Quality Standards to meet superior performance criteria. You will find your new tool easy and safe to operate, and, with proper care, it will give you many years of dependable service. The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use. Wear hearing protection.
increase the risk of electric shock. General safety rules d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
energising power tools that have the switch on invites accidents. measures reduce the risk of starting the power tool accidentally. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
plug from the power source before installing or removing an accessory. Never use dull blades in the tool. They will cut slower, leave rough cuts and break easily due to added pressure and excessive heat. They will also overload the motor and cause premature failure of the tool. Never use damaged or bent blades. They will be brittle and break easily possibly causing injury to the operator. Never touch a saw blade immediately after using the tool. The blade will be extremely hot and will burn your hand.
Accessories Unpacking 1 x 6 mm Hex key/ Allen Key Due to modern mass production techniques, it is unlikely that your AUTOMATIC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.
Installing blade accesssories Notes: a) Check to make sure the convex curve of the washer is facing the head of the screw. b) Make sure the alignment holes in the blade are still mated with the alignment pins in the accessory holder. All accessories are installed on the oscillating tool in a similar manner. For the purposes of describing the accessory installation, the plunge cutting blade is used. 5. Firmly tighten the screw with the 6 mm hex key.
Installing sanding pad and sandpaper OFF switch toward the front of the tool. 2. To turn the tool OFF, press the rear part of the ON/OFF switch and allow the switch to slide to off position. 1. Install the hook & loop sanding pad onto the tool. Flush cutting a door jamb and casing for installing flooring Notes: a) The big washer is NOT required to install the sanding pad. Use the 2 x washers as indicated on Page 8 for the sanding pad installation.
Note: The tool and blade should be at a 45° angle to the floor to allow the corner of the blade to plunge cut into the flooring. 5. While holding the tool tightly, slowly plunge the corner of the blade into the flooring until it cuts through the flooring. Once the plunge cut is complete, then complete the cut to the corner of the rectangle. floor tile. Note: Hold the tool tightly and do not put too much forward pressure on the saw blade when cutting, as this will cause the tool to vibrate excessively. 5.
accessories. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury. It will also void the warranty. Lubrication Using the scraper blade 1. Install the scraper blade on the multi-tool.
DISTRIBUTED BY; Global Power Brands International Pty. Ltd. PO Box 413 Mooroolbark VIC 3138 ABN. 39 131 999 914 Ph. 1800 909 909 help@globalpowerbrands.
