Instruction manual

ManualsBrandsAutomatic Technololgy ManualsGarage Door OpenerGDO-9v2 Enduro Gen 2

SMARTSOLAR

KIT GEN2

ITEM DESCRIPTION QTY

1 SOLAR PANEL - 30 WATT STP030-12/Lb 1

2 BATTERY PACK (2 X 12 Ah) 1

3 CHARGER BOARD (WITH HARNESS) 1

4 ACCESSORY PACK 1

SmartSolar

™

Kit

Solar Power Kits For Automatic Technology Openers

ACCESSORY PACK

ITEM DESCRIPTION QTY

5 2 PIN SOLAR SHUNT 1

GEWIS MOUNTING KIT (64805)

6 MOUNTING LUGS FOR GEWISS BOX 4

7 SCREW “P” M3.5 X 13 4

SOLAR BATTERY CABLE KIT (61821)

8 CABLE 2 CORE R&B X 1.0MM (2.5M) 1

9 NYLON GLAND M16-07B 1

SOLAR PACK 01 (61783)

10 PAN HEAD SCREW M4 X 8 4

SOLAR PACK 02 (61784)

11 TAPTITE SCREW “P” M4 X 8 4

SOLAR PACK 03 (61492) (GDO-8 ONLY)

12 BRUSH CARD 2047 L/F HARNESS 1

13 NYLON CABLE GLAND PGB7-07B 2

14 PAN HEAD SCREW M6 X 12 1

15 WASHER 6.4X20.6X1.2 GAL 1

16 WASHER RUBBER 1/16’X1”X3/8” 1

17 TIE MOUNT CM-13 (ADHEISIVE) 4

18 CABLE TIE 4” GT-100M 4

SOLAR PACK 04 (61786)

19 TAPTITE SCREW “P” M3 X 8 4

SOLAR PACK 05 (61787) (GDO-9 ONLY)

20 THRUSS SER HD SCREW “S” M4 X 8 2

21 TAPTITE SCREW “P” M4 X 8 3

22 PCB SUPPORT 76X27 1

Installing the Solar Panel

Unpack the Kit

Unpack the Battery Box and the Solar Panel and inspect them for any

damage in transit.

Mount the Solar Panel

a. Determine a mounting point for the solar panel as close as possible

to the intended opener. The length of cable from solar panel to solar

charger must not exceed 5m.

b. The solar panel should be faced to the North for maximum effect. Solar

panel output is directly proportional to the amount of sunlight to which

it is exposed. Thus, the panel should be positioned to the north due

to Australia’s southern location.

c. The angle to tilt the solar panel for maximum exposure to the sun is

determined by the following equation: α° = L° + 15°

Where “α°” is panel’s tilt angle from the horizontal, and “L°” is

the latitude of the mounting location. Refer to table, for a list of

pre-calculated panel angles for major centres in Australia.

α°

L°

TOWN Latitude

(L°)

Panel Angle

(α°)

HOBART 42.5º S 57.5º

MELBOURNE 37.5º S 52.5º

CANBERRA, ADELAIDE, AlLBANY 35º S 50º

SYDNEY 33.5º S 48.5º

NEWCASTLE, BROKEN HILL, PORT

AUGUSTA, PERTH

32.5º S 47.5º

BRISBANE, OODNADATTA,

GERALDTON

27.5º S 42.5º

TOWNSVILLE, TENNANT CREEK,

PORT HEDLAND

20º S 35º

DARWIN 5º 20º

Doc # 160035_02

Part # 13345

Released 30/05/14

Gen 2

Summary of content (8 pages)

PAGE 1
SmartSolar™ Kit Gen 2 Solar Power Kits For Automatic Technology Openers ACCESSORY PACK ITEM 1 5 DESCRIPTION QTY 2 PIN SOLAR SHUNT 1 GEWIS MOUNTING KIT (64805) 2 6 MOUNTING LUGS FOR GEWISS BOX 4 7 SCREW “P” M3.5 X 13 4 8 CABLE 2 CORE R&B X 1.0MM (2.
PAGE 2
Swing Gate Opener Set Up DCB-05V2 7 6 2 9 3 1 8 11 IMPORTANT WARNING! WARNING! Do not connect the batteries until you have connected wiring on the charger board. Do not connect battery or solar panel polarity incorrectly - this will result in serious damage to components. Mount the Charger Board a. Unplug the Control Box from mains power. b. Remove the Control Box’s cover, then remove the transformer, EMC board (if fitted) and mains power cable. c.
PAGE 3
Sliding Gate Opener Set Up NeoSliderTMV2 7 6 11 2 9 3 8 WARNING! Do not connect the batteries until you have connected wiring on the charger board. IMPORTANT WARNING! Do not connect battery or solar panel polarity incorrectly - this will result in serious damage to components. 1 Mount the Charger Board a. Unplug the drive unit from mains power. b. Remove the main cover, then remove the transformer, EMC board (if fitted) and mains power cable. c.
PAGE 4
Roll Up Door Opener Set Up GDO-6V4 EasyRoller®, RDO-1V3 7 6 2 11 9 3 SOLAR SHUNT 8 5 WARNING! Do not connect the batteries until you have connected wiring on the charger board. 1 Mount the Charger Board a. Unplug the drive unit from mains power. b. Disengage motor using manual release cord. c. Remove the main cover, timing cover and light diffuser, then remove the transformer, EMC board and mains power cable. d. Fix the Charger Board 3 under the timing cover using four (4) M4x8 screws 11 . e.
PAGE 5
Roll Up Door Opener Set Up GDO-8 EasyRoller® 13 12.5mm Drilled Hole 13 14 15 16 3 17 20 18 30 12 1 2 8 6 9 IMPORTANT WARNING! Do not connect battery or solar panel polarity incorrectly - this will result in serious damage to components. 7 Insert the Solar Panel’s Wires a. Unplug the drive unit from mains power. b. Remove the controls cover and chassis enclosure, then remove the transformer and EMC board. c. Remove the mains power cable, then fit a nylon gland 13 to its hole in the chassis.
PAGE 6
Overhead Door Opener Set Up GDO-9V2 GEN2 Enduro, GDO-9V3 GEN2 Dynamo, SDO-2V2 CAD P Diamond & SDO-3V2 CAD S 21 3 7 6 20 22 2 9 8 SOLAR SHUNT WARNING! Do not connect the batteries until you have connected wiring on the charger board. 5 1 Mount the Charger Board a. Unplug the drive unit from mains power. b. Remove the screws and swing open the main cover and remove the light diffuser. c. Remove the transformer, EMC board (if fitted) and mains power cable. d.
PAGE 7
Specifications SmartSolar™V2 Technical Specifications* Garage Door Slider Swing Gate Load Voltage 24 24 24 Load Continuous Current 3 - 5A 5A 5 - 10A Number of Cycles per Day 10 10 10 Average Cycle Time (Opening and Closing) 40 seconds 90 seconds 72 seconds - Without P.E. Beams 100mA 100mA 100mA - With P.E. Beams 180mA 180mA 180mA Max. Standby Current - With 2 x P.E. Beams Average total consumption current per day 260mA - Without P.E. Beams 2.75 - 3Ah 3.7Ah 3.4 - 4.
PAGE 8
Important Safety Instructions WARNING! • • • • • • ELECTROCUTION! DO NOT short the output of batteries. Serious personal injury and/or property damage can result from failure to follow this warning DO NOT connect battery wires incorrectly to solar charger - Observe the polarity carefully! During charging and discharging cycles the lead-acid batteries may release explosive gases.