DOMINATOR EasyRoller ® Light-duty Commercial Rolling Door Opener Instruction Manual (Instruction d’Installation) FOR LIGHT-DUTY COMMERCIAL DOOR USE ONLY Doc # 160402_00 Part # 87035 Released 10/05/19 Conforms to UL 325 4008033 Certified to CSA C22.2 No.
WARNING!: It is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and remote control opener damage. Please save these instructions for future reference. ELECTROCUTION!: To reduce the risk of electric shock, this equipment has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type outlet.
© Copyright 2018 CONTENTS Rolling Garage Door Operator 1. Safety Information 2. System Specifications 3. Kit Contents 4. Setup Requirements 4 6 7 7 4.1 Tools Required 7 4.2 The Opener: 8 4.3 Unsuitable Door Types 8 4.4 Sideroom 8 5. Operator Safety & Security 9 5.1 Your Door CAN NOT be used by the opener when: 9 5.2 Your Door CAN be used when: 9 5.3 To Disengage the Opener: 9 5.4 To Re-Engage the Opener: 9 6. Installation Instructions 6.1. Door Preparation 6.2.
1. Safety Information WARNING! •• This operator should be installed in accordance with relevant US and Canada Standards. •• To reduce the risk of injury to persons – Use this operator only with a rolling door. The drive must not be used with a door incorporating a wicket door, unless the drive cannot be operated with the wicket door open. •• This operator is a plug in domestic appliance and is designed for indoor use only. It must be installed in a dry position that is protected from the weather.
© Copyright 2018 1. Sécurité AVERTISSEMENT ! •• Cet appareil doit être installé conformément aux normes US et canadiennes en vigueur. •• Pour réduire les risques d’accident, n’utiliser cet appareil qu’avec une porte de garage enroulable. Ce moteur ne doit pas être utilisé avec une porte de garage avec portillon, à moins que le moteur ne puisse fonctionner quand le portillon est ouvert.
2. System Specifications Technical Specifications Power supply Maximum door opening Door Height: Maximum Door Weight: Door Area: Minimum sideroom Dominator EasyRoller® 120Va.c. 60Hz 3.25 turns of the drum wheel (approx. 9.
© Copyright 2018 3. Kit Contents 9 1 5 7 2 8 6 3 4 1. 2. 3. 4. 5. 6. Dominator EasyRoller drive unit 2 x Locking Bar Covers Premium Remote Control Wall Control 1 x Weight Bar 1 x Wired Safety Beam kit with brackets and screws Fastner Bag 7. 2 x Nilock Nut 8. 2 x 3/16 x 1/2 flat washers 9. 2 x Pan Head Screw M4 x 50mm Fig. 3.1 4. Setup Requirements 4.
4. Setup Requirements 4.2 The Opener: a. b. c. d. e. MUST BE installed in a dry position, protected from weather. (Moisture or corrosion not covered by Warranty) Is factory set for RIGHT HAND SIDE installation (from inside garage), but capable of LEFT HAND SIDE installation. Fig 4.2.1 REQUIRES properly earthed 3 pin single phase power within an arms length of door and at a suitable height Requires a MINIMUM SIDEROOM of 40mm from the edge of the door to the inside of the door bracket and 85mm to the wall.
© Copyright 2018 5. Operator Safety & Security 5.1 Your Door CAN NOT be used by the opener when: a. b. There is a locking device installed. There is a power failure. MANUAL RELEASE 5.2 Your Door CAN be used when: a. b. There is an emergency, by disengaging the opener. There is a power failure, by disengaging the opener. 5.3 To Disengage the Opener: a. b. c. It is recommended to do so with the door in the closed position. Pull down on the manual release cord, until you hear a click.
6. Installation Instructions IMPORTANT INSTALLATION INSTRUCTIONS. WARNING - To reduce the risk of severe injury or death: (1) READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. (2) Install only on a properly operating and balanced garage door. An improperly balanced door has the potential to inflict severe injury. Have a qualified service person make repairs to cables, spring assemblies, and other hardware before installing the opener.
© Copyright 2018 6.1. Door Preparation 6.1.1 Prepare the Door: a. b. c. d. Clean the guides if there is any oil or wax present using a suitable white spirit. The only lubricant suitable for use on door guides is silicon spray. DO NOT use WD-40, RP-7, petroleum grease, or similar. Remove the locking bars or disable the lock. Install the locking bar covers 2 if there are locking bar holes in the guides. This ensures fingers cannot be placed in the holes while the door operates. (Fig 6.
6.3. Pinning the Door 6.3.1 Pinning the Door to the drum: Screw into the low part of grove NOTE: Pinning of the door is mandatory and is primarily required in order for the inherent entrapment protection to function properly. Pinning the door’s curtain to its drum maintains security when the opener is closed. If the curtain is not pinned the door can be partially opened manually. (Fig 6.3.1) a. Fully close the door. b. Mark a minimum of two (2) drill holes on the drum to each end of the door. (Fig 6.3.
© Copyright 2018 6.5. Mounting the Opener 6.5.1 Raising the Door: a. b. When in position, remove the U-bolt (or bolts) and saddle from the door bracket. Lift the door up and away from the wall until clear of the door bracket, before lowering the door to rest on the door stand or prop. (Fig 6.5.1) NOTE: If there is limited ceiling space to lift the door, the door bracket may have to be removed.
6.6 Safety Beam Installation IMPORTANT NOTE: The Safety Beam must be installed and connected before the travel limits are set. 6 7 6.6.1 Safety Infra-Red Beam Kit (P/N 62047) A Safety Beam extends across the door opening. This Safety Beam is designed to detect an obstruction while the door is closing and to send a signal to the door operator to reverse or stop the door movement. Install the Safety Beam indoor only. 3 8 5 6.6.2 Assembling the Mounting Bracket a. b. c. d.
© Copyright 2018 6.7. Setting the Travel Limits 6.7.1 Initial Preparation: a. b. Move the door to the half way position. Engage the opener by pulling down on the manual release string until a click sounds (Fig.6.7.1). c. d. Remove the clear button cover from the unit. Switch power on to the opener. The red CLOSE LIMIT LED will be flashing. e. Press and hold the CLOSE button - the door should start closing.
6.8 Testing & Setting Safety Obstruction Force 6.8.1 Testing the Close Cycle Press the OPERATE button to open the door (Fig.6.8.1). Place an object approximately 1-1/2”(38mm) high (or a 2”x 4” board laid flat) on the floor under center of garage door opening (Fig.6.8.2). c. Press the OPERATE button to close the door. d. When door contacts the object, the door must stop (within 2 seconds) and reverse to open position. If the door does not properly reverse. • Check the “close” limit position.
© Copyright 2018 6.9 Accessories 6.9.1 Terminal Block A variety of wired accessory items can be connected to the terminal block J7 such as Safety Beam, Electric Key Switch and more (Fig. 6.9.1). Terminal connections from top down are as follows: 1. V+ (+35V/+24V); 2. EB1 (Safety Beam input, mandatory); 3. 0V (0V for Safety Beam); 4. EB2 (Safety Beam input); 5. 0V (Common ground for accessories and Safety Beam); 6. OSC (Open/Stop/Close trigger) 7. AUX OUT (Auxiliary output trigger) V+ EB1 OV EB2 Fig.6.9.
6.10 Coding Transmitters 6.10.1 Setting Premium Remote Control and Wall Control Codes The opener can only operated from remote control transmitters that have been programmed into its memory. Up to 64 codes can be stored in the memory. a. Press and hold the DOOR CODE button (Fig 6.10.1). b. Press Button 1 on the transmitter for two seconds. Release and pause for two seconds. Press the Button 1 again for two seconds. c. Release the DOOR CODE button. The transmitter button is now coded, press to test.
© Copyright 2018 6.10 Coding Transmitters TRANSMITTERS COMPLIANCE STATEMENT THIS DEVICE COMPLIES WITH PART 15 OF THE FCC AND INNOVATION, SCIENCE AND ECONOMIC DEVELOPMENT CANADA LICENCE-EXEMPT RSSs. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
6.11 Auto-Close 6.11.1 Safety Beams A Safety Beam Kit may be fitted to this opener. When this option is fitted, the operation of this device is such that if an object (i.e car, child etc) blocks the Infra-Red beam, then the garage door opener will not close the door automatically. If the Safety Beam is fitted but not operating correctly, then the door once opened automatically, will not close automatically. 6.11.
© Copyright 2018 6.12 Attach Warning Labels 6.12.1 Placement of Warning labels • Attach the entrapment warning label on the wall near the door control with tacks or staples at a minimum hright of 5 feet above floors, landings, steps or other adjacent walking surface so shall children are not able to reach it. • Place the attached entrapment warning label on wall. Use an additional mechanical means (plate, board etc.) which can secure the labels to surfaces to which the adhesive will not adhere.
7. Operation Instructions IMPORTANT SAFETY INSTRUCTIONS WARNING! TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: (1) READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. (2) NEVER LET CHILDREN OPERATE OR PLAY WITH DOOR CONTROLS. KEEP THE REMOTE CONTROL AWAY FROM CHILDREN. (3) ALWAYS KEEP THE MOVING DOOR IN SIGHT AND AWAY FROM PEOPLE AND OBJECTS UNTIL IT IS COMPLETELY CLOSED. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. (4) NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR. (5) TEST DOOR OPENER MONTHLY.
© Copyright 2018 7.1 How to Use Your Operator CAUTION: Activate the operator only when the door is in full view, free of obstructions and with the operator properly adjusted. No one should enter or leave the garage while the door is in motion. Do not allow children to play near the door. For maximum efficiency of your operator, your garage door must be in good operating condition. An annual service of your garage door by door professional is recommended.
7.2 User Operating Controls Button Function 1. OPERATE Opens/stops/closes the door 2. CODING LED (Red) Flashes when a code is being stored or when the transmitter button is pressed 3. LIGHT CODE (White) Is used for storing or erasing the transmitter button (code) you wish to use to switch the courtesy light on the opener on or off. 4. DOOR CODE (Blue) Is used for storing or erasing transmitter buttons for door operation 5.
© Copyright 2018 8. User Maintenance Instruction WARNING! Run the Safety Testing procedures MONTHLY in Section 6.8 to ensure garage door is fit for use. 8.1 Door Maintenance A poorly maintained door could cause fatal / serious injuries or damage to property. a. Frequently examine the door, particularly the cables, springs and mountings for signs of wear, damage or imbalance. DO NOT USE if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury. b.
9. Troubleshooting Symptom Possible cause Remedy The opener does not work from the transmitter Garage door in poor condition e.g. springs may be broken Check the door’s operation The opener does not have power Plug a device of similar voltage (e.g.
© Copyright 2018 10. Customer Agreement & Warranty PLEASE READ THIS AGREEMENT CAREFULLY TO ENSURE THAT YOU UNDERSTAND EACH PROVISION. THIS AGREEMENT REQUIRES THE USE OF ARBITRATION ON AN INDIVIDUAL BASIS TO RESOLVE DISPUTES, RATHER THAN JURY TRIALS OR CLASS ACTIONS, AND ALSO LIMITS THE REMEDIES AVAILABLE TO YOU IN THE EVENT OF A DISPUTE.
and any other owner of intellectual property whose protected property may appear on any website and/or dialogue box controlled by ATA or accessed through the ATA’s websites. Except for material in the public domain, all material displayed in association with the Product is protected by copyright or trademarks. Except for personal, noncommercial use, this material may not be copied, downloaded, redistributed, modified or otherwise exploited, in whole or in part, without the permission of the owner.
© Copyright 2018 eventualities arising from any failure to comply with the requirements in paragraph (a) above. (c) You are solely responsible for any data or network charges incurred using the Control Kit Bundle. (d) You must comply with any applicable third party terms of agreement which are displayed to you, or otherwise brought to your attention, in the course of downloading or registering to use any part of the Control Kit Bundle. 3.
(e) By using the Compatible Apps, you represent and warrant that: (i) you are not located in a country that is subject to a U.S. Government embargo, or that has been designated by the U.S. Government as a ‘terrorist supporting’ country; and (ii) you are not listed on any U.S. Government list of prohibited or restricted parties. 9.
© Copyright 2018 Dominator EasyRoller Instruction Manual Diamond PD Power Drive : Instruction Manual 31
Automatic Technology America VIneyard Centre II, 1452 Hughes Road, Grapevine, Texas 76051, United States of America P: +1 817 873 5076 W: www.ata-america.
