MULTI TESTER PRO User manual A37MAN I318495 Iss3
Multi Tester Pro User Manual Part Number A37MAN EN Issue 3 © Autodiagnos 2011 Part Number A37MAN EN - Issue 3 © Autodiagnos 2011
Contents Introduction Copyright ................................................................................................ 1 Introduction............................................................................................. 1 Getting Started Setting up ............................................................................................... 2 Multi-Cartridge Manager - Installation ............................................................. 2 Multi-Cartridge Driver - Installation ......
Contents Training ......................................................................................................... 32 Autodiagnos Website .................................................................................... 32 Contact Details Addresses............................................................................................. 33 Parts list ................................................................................................
Introduction Introduction Copyright The contents of this document may be changed without prior notice, and should therefore not be regarded as being binding on Autodiagnos. Autodiagnos declines all responsibility for faults and omissions, which may occur in this document, or the hardware & software described herein. Under no circumstances can Autodiagnos be held responsible for damage, which could occur due to use of this document, or of the hardware and software described herein.
Getting Started Getting Started Setting up Multi-Cartridge Manager - Installation The Multi-Cartridge Manager software is used to manage the information held on the Multi-Cartridge. It allows software applications and customer licence information to be updated when required. It is recommended that this software is installed immediately, by following these steps: Note: Do not connect the Multi-Cartridge until advised. 1. Insert the CD into the drive; it should auto-run and display the ‘Autodiagnos’ window.
Getting Started Multi-Cartridge Driver - Installation 1. Once the Multi-Cartridge Manager installation is complete, connect the Multi-Cartridge to a USB port on the PC. Windows will detect a new device and display the installation wizard. Select ‘No, not this time’ and press ‘Next >’ to continue.
Getting Started 2. Select ‘Install the software automatically’ and press ‘Next >’. Windows will install the USB driver from the CD. 3. If a warning message saying that the driver ‘.... has not passed Windows Logo testing....’ is displayed, press ‘Continue anyway’. 4. The Multi-Cartridge Manager software is now ready to use.
Getting Started Multi-Cartridge Driver - Update If the above error message is displayed when trying to start the Multi-Cartridge Manager software but no ‘Found New Hardware’ message has appeared, then the following procedure will update the driver. Note: This procedure must be repeated for each USB port to which the Multi-Cartridge is connected. 1. Ensure the latest Autodiagnos CD is in the CD drive and the Multi-Cartridge is connected to the PC.
Getting Started 2. To update the driver used for the Multi-Cartridge press the right mouse button on ‘My Computer’ (which can be found either on the desktop or within the ‘start’ menu), select ‘Properties’ then the ‘Hardware’ tab followed by the ‘Device Manager’ button.
Getting Started 3. Look for any unknown device. An unknown device will normally be highlighted by either a yellow ‘!’ or ‘?’.
Getting Started 4. Reconnect the Multi-Cartridge to the PC and press the right mouse button on the ‘unknown device’. Select ‘Update Driver’ to display the above message box. 5. Select ‘No, not this time’ then press the ‘Next >’ button. 6. Select ‘Install the software automatically’ then press the ‘Next >’ button.
Getting Started 7. Press ‘Continue Anyway’. 8. The Multi-Cartridge is now a recognised USB device. The Multi-Cartridge Manager software is ready to use.
Getting Started Connecting Multi-Cartridge Manager 1. Connect Multi-Cartridge to the PC using the USB cable. 2. Launch the Multi-Cartridge Manager from the icon on the Desktop. Click ‘OK’ to begin connecting to the cartridge. 3. If the ‘Found New Hardware’ message appears, repeat the ‘Multi-Cartridge Installation’ procedure. See ‘Multi-Cartridge Driver - Installation’, page 3. 4.
Getting Started 5. If the following message box appears, the desired operating language must be selected.
Getting Started Downloading applications 1. When connecting to the Multi-Cartridge, software versions are checked by the application. User requirements are represented by a 'tick'. A tick will be shown against all loaded applications; the configuration of loaded applications can be modified at any time to suit requirements. The removal of a tick will result in a particular application being deleted from the cartridge at the point the 'Update Application' button is selected. 2.
Getting Started 5. When all required applications have been updated the above message will be displayed. Press the ‘OK’ button to continue. Updating License A unique license key is provided by Autodiagnos for every Multi-Cartridge. License keys provide the Multi-Cartridge with application and subscription information. 1. Press the ‘Update License’ button. 2. Enter the new license key in the text box. 3. Press the ‘OK’ button to confirm.
Getting Started Software updates - Website The ‘Downloads’ area of the www.autodiagnos.com website allows users of the Multi-Tester Pro to obtain the latest releases and beta releases of vehicle application software. The ‘Downloads’ area of the website provides the following. Latest Beta versions of software applications. Beta versions are applications that are currently under development and test. No support is offered for Beta version software. Latest software applications release notes.
Getting Started Snapshot Reader - Installation 1. To install the software press the ‘Install Snapshot Reader’ button and follow the prompts.
Using Multi-Tester Pro Using Multi-Tester Pro Getting familiar with Multi-Tester Pro Connection points 1 12V DC 2 AU0062 1. Connection to PC. 2. Connection to vehicle serial interface.
Using Multi-Tester Pro Display and keys 3 1 2 AU0061 1. Display Backlit. Displays graphics and text. Can show text with pictures and graphs. Lighting switches off if no key is pressed within 5 minutes. This extends life of back lighting. Press any key to switch display on. 2. Keypad Twelve keys. Keys not used for a particular phase are inhibited. 3. Cartridge Contains the program for the desired application.
Using Multi-Tester Pro Typical screen layout Global ECU Test Drive Chassis Body Read DTC memory from all supported modules AU0069 1. Header. 2. List of menus - the selected alternative is marked. 3. Explanation of selected alternative. 4. List of permitted keys. 5. Explanation of function keys.
Using Multi-Tester Pro Keypad operation 1 6 2 3 5 4 AU0063 1. Select the function key according to instructions on the display. 2. Use and to move between menu selections or to update groups of figures. 3. Use and to move between numbers when updating figures, or to scroll through long text strings. 4. Press to activate the selection. 5. Press to leave a function and return to the previous menu. 6. Select to obtain diagnostic help information.
Using Multi-Tester Pro Connections To ensure reliable communications with any module selected, the following steps should be followed. 1. Identify the vehicle and refer to the vehicle application list found on the CD to ensure the application is supported. 2. Locate the vehicle diagnostic connector. 3. Select the correct cable configuration using the quick guide chart. See ‘Cable Quick Guide Chart’, page 21. 4. Connect the required cable(s) to the Multi-Tester Pro. 5.
5 21 5 * Requires Battery Cable 12V PSA 2 (A0904051)* BMW (A0904081-1) Mercedes (A0903001-2) Renault (A0903091-1) Ford (A0903061-3)* PSA 1 (A0903051) 16 pin OBD(OM3000/10) 3 Mercedes Sprinter (A09040001-1) VW LT 35 (A0904021-1)* Fiat (A090307-2)* Rover (A0903111-1)* Landrover 2 way (A0903121-1)* Opel (A0903031-1) 3 VAG 2x2 pin (A0903021-1) Landrover 1 way (A0904121-1)* 16 pin OBD(OM3000/10) Multi -Tester-Pro Using Multi-Tester Pro Cable Quick Guide Chart 1 2 3 4 5 AU0064
Using Multi-Tester Pro Display and Keys Communicate When connected to the vehicle diagnostic connector, the Multi-Tester Pro will power up and execute a self test procedure. Once complete, the main menu will display the vehicle manufacturers currently available on the Multi-Cartridge. To start communications, use the keypad to navigate through the menu and follow on-screen prompts when displayed. Each car manufacturer has its own specific menu.
Using Multi-Tester Pro Functionality Overview Each system will have a specific set of functions described thereafter. Most functions will provide the opportunity to take a snapshot using the function keys. Electronic Control Unit (ECU) Identification: The ECU identification will give the electronic signature of the ECU. Read Diagnostic Trouble Code (DTC) memory: All registered DTCs in the relevant ECU are indicated on the display. Use and to move the cursor for more information on each DTC.
Using Multi-Tester Pro AU0035 To delete a DTC, Use and to select it and press ‘F2’. AU0036 Confirm the deletion by pressing ‘YES’ or cancel the function by pressing ‘NO’. The stored DTCs will be erased from the ECU memory. Engine: Erase DTCs The stored DTC could not be erased! Press ENTER to read ECU memory again AU0038 If the DTCs were not successfully erased, the above message is displayed.
Using Multi-Tester Pro Monitor list L6A MM8P: Select List Battery Voltage Coolant Temp Map Sensor Throttle Position Engine speed Idle air control O2 Sensor loop 02 Sensor EGR Yes No Yes No No No No Yes No Coolant Temperature Sensor / /ENTER/EXIT F1:Help F2: F3:Deselect all AU0040 Multi-Tester Pro reads current data from the car's control unit. The values are updated continuously. It is possible to modify the monitor list so that only selected parameters are displayed.
Using Multi-Tester Pro Actuators AU0041 In most cases, the actuators can simply be switched on and off using the ‘YES’ or ‘NO’ button on the Multi-Tester Pro. The ‘F1’ key can also be used to toggle the actuator automatically, leaving the operator free to inspect the system under test.
Using Multi-Tester Pro Reset adaptation values It is possible to reset some systems to their original adaptation values. (e.g. BMW DDE5.0). Self Test Some systems can perform a self-test and then display the trouble codes that have been logged during this test. Module Synchronisation The Multi-Tester Pro can synchronise replacement ECUs. When replacing a defective ECU, it may be necessary to synchronise the new ECU to other ECUs in order for it to function correctly.
Using Multi-Tester Pro Snapshot Reader functions During diagnostic procedures, the Multi-Tester Pro has the facility to save a snapshot of information. The information can be viewed on the Multi-Tester Pro at a later time or can be downloaded to a PC, using the Snapshot Reader application. To use this feature, press the F3 button during a diagnostic test procedure and the currently viewed information will be saved within the Multi-Tester Pro memory.
Using Multi-Tester Pro AU0044 3. Select the ‘View Snapshots’ menu, then select ‘Download Snapshots to PC’. 4. Start the snapshot download. If required, complete the Customer and Vehicle Details and then press the ‘LOAD’ button.
Using Multi-Tester Pro 5. If required, complete the Customer and Vehicle Details and then press the ‘LOAD’ button. If all the settings are correct, the snapshots will be extracted from the Multi-Tester Pro, processed, and displayed in your default web browser. 6. The snapshot is automatically saved to a file called ‘Snapshot.html’. To save the snapshot, it must be saved under another name. Select ‘Save’ from the ‘Snapshot’ menu and file the new snapshot. 7.
Support Services Support Services Product Support When assistance is required to ensure efficient operation of the Multi-Tester Pro please visit www.autodiagnos.com or contact your supplier. Product Support services include: Autodiagnos software installation; Multi-Cartridge updating; diagnostic socket locations; application coverage; communication issues; Diagnostic Trouble Code identification; procedural help; service and repair of equipment.
Support Services Training With vehicle systems becoming increasingly complex, training has never been as important. With this in mind Autodiagnos Ltd believes that dedicated training courses will benefit technicians using the Multi-Tester Pro and allow it to be used to its full potential. Please contact your supplier for details of all available services. Autodiagnos Website Visit the ‘Support’ section at www.autodiagnos.com to keep up to date with useful information and procedural help.
Contact Details Contact Details Addresses United Kingdom Germany USA Autodiagnos Ltd Autodiagnos Omitec Inc Hopton Estate Deutschland GmbH 29777 Telegraph Road London Road Rödelheimer Bahnweg 21-23 Suite 1637, Onyx Plaza Devizes, SN10 2EU 60489 Frankfurt Southfield United Kingdom Germany MI 48034 Tel: +44 (0) 870 949 3799 Tel: +49 (0) 700 28 86 34 24 Tel: +1 800 434 6744 Fax: +44 (0) 1380 732 001 Fax: +49 (0) 700 28 86 34 23 Fax: +1 248 799 9222 www.autodiagnos.com www.autodiagnos.
Appendix A: Replacement parts Replacement parts Parts list Cable Description Part Number 2m 25 to 16 pin J1962 cable OM3000/10 Battery cable A010202-2 BMW 20 to 25 pin cable A0904081-1 Fiat 3 to 16 pin cable A090307-2 Ford 2/3/4 to 16 pin cable A0903061-3 Land Rover 1-way cable A0904121-1 Land Rover 2-way cable A0903121-1 Mercedes 38 to 25 pin cable A0903001-2 Mercedes Sprinter cable A0904001-1 Opel/Vauxhall 10 to 16 pin cable A0903031-1 PSA 2/4 to 25 pin cable A0904051 PSA 30 to 25
Autodiagnos Limited Unit 1 Hopton Estate • London Road • Devizes SN10 2EU Tel: 0870 949 3799 • Fax: 0870 949 3702 www.autodiagnos.
