Autodesk Visual Effects, Finishing, and Color Grading ® HP Z800 Workstation Hardware Setup Guide ®
Autodesk® Visual Effects, Finishing and Grading 2010 © 2009 Autodesk, Inc. All rights reserved. Except as otherwise permitted by Autodesk, Inc., this publication, or parts thereof, may not be reproduced in any form, by any method, for any purpose. Certain materials included in this publication are reprinted with the permission of the copyright holder. Portions relating to MD5 Copyright © 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.
Contents Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 About This Guide . . . . . . . Related Documentation . . . . Notation Conventions . . . . Contacting Customer Support Chapter 2 Getting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Media Storage . . . . . . . . . . . . . Connecting the Fibre Channel Adapter . . . . . . Connecting Storage Enclosures . . . . . . . . . . Connecting XR 6500 Storage . . . . . . . . Connecting XR 6412 Storage . . . . . . . . Connecting XR 5402 and XR 5412 Storage . Connecting Archiving Storage . . . . . . . . . . . Filesystem Devices . . . . . . . . . . . . . . SCSI Tape Drive Devices . . . . . . . . . . . Chapter 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction 1 Topics in this chapter: ■ ■ ■ ■ About This Guide on page 1 Related Documentation on page 1 Notation Conventions on page 2 Contacting Customer Support on page 2 About This Guide This guide describes how to set up the HP Z800 workstation hardware and wiring for an Autodesk® Visual Effects, Finishing, or Colour Grading application.
At various places in this guide, references are made to other documents.
Getting Started 2 Topics in this chapter: ■ ■ ■ ■ General Workflow on page 3 Typical Configuration Overview for Visual Effects and Finishing Applications on page 5 Typical Configuration Overview for Autodesk Lustre on page 6 Hardware Configuration Guidelines on page 9 General Workflow The following procedure provides the general workflow for connecting, configuring and installing an Autodesk® Visual Effects, Finishing, or Colour Grading application on a HP Z800 workstation.
NOTE The Windows operating system is not supported by Lustre on the HP Z800 workstation. 7 Install and license the Visual Effects, Finishing, or Colour Grading application. As above, see the application Installation and Configuration Guide.
Typical Configuration Overview for Visual Effects and Finishing Applications The following illustration shows a typical configuration, including the Wacom tablet, and other optional components. Workstation Peripheral Options WACOM Tablet Video Options AJA BOB (breakout box) AES/EBU Audio Video MonitorOut In Out Ch. 1/2 In Ch. 3/4 In Ch. 5/6 In Ch. 7/8 In Ch. 1/2 Out Ch. 3/4 Out Ch. 5/6 Out Ch. 7/8 Out Ch. 1/2 In Out Ch. 3/4 In Out Ch. 5/6 In Out Ch.
Typical Configuration Overview for Autodesk Lustre A Lustre system consists of a number of different hardware and software components. This section describes each of the hardware components in a Lustre installation, and the software associated with each component. You may or may not have all of the components listed here in your Lustre setup. The type of workgroup, as well as the feature set you purchase for each of the workstations in that workgroup, determine the components in your installation.
Control Surface The Autodesk Control Surface provides improved interactivity when colour grading film and video footage. You can perform many of the same tasks you do in the Lustre user interface using the Control Surface. You connect the Autodesk Control Surface to a Master Station or HD Station, and configure the Control Surface on the workstation to which it is connected. Video I/O Card and Breakout Box On the HP Z800 workstation, video I/O is provided by the AJA card.
The following illustration shows a typical Lustre workgroup configuration built around a Master Station. It includes a Lustre Station, and other optional components. Control Surface R Grade InPr Curve OutPr K ey C URVES GRADE KEY Geom G EOM G Hue BBrigh t 00019 #0001.
Hardware Configuration Guidelines In most cases, hardware integration and application installation are done on delivery by an authorized technician, and some of the procedures in this guide may not be necessary. Still, it is a good idea to read through all chapters to familiarize yourself with the configuration procedures for the following reasons: ■ Many suspected problems with your system may be due to loosened connections or improperly configured devices.
The following table summarizes the peak (at startup) power consumed by the system and the heat it generates under the maximum processing load produced by a Visual Effects, Finishing, or Colour Grading application. For more detailed specifications, including noise output, see the documentation provided by the manufacturer. Component Quantity Startup Amps (120V / 240V) Cont. Amps (120V / 240V) Watts Heat (BTUs) Workstation (with cards) 1 4.0 / 2.0 3.8 / 1.9 456 1556 Lucid ADA 88192 1 0.5 / 0.
■ Wear a grounded static wrist strap. Attach the strap's alligator clip to any grounded metal surface on the component's chassis that you are working on. Place the wristband around your wrist. ■ Do not handle any components unnecessarily, particularly boards and cards that slide in and out of PCI slots on their parent hardware components. Grounding Audio Hardware Components It is important to properly ground the audio components. Otherwise, ground loops can occur, causing humming in the system.
12
Connecting Peripherals 3 Topics in this chapter: ■ ■ ■ ■ ■ ■ ■ Overview of Peripheral Connections on page 13 Connecting the Graphics Monitor on page 14 Connecting the Keyboard, Mouse, and Tablet on page 15 Connecting the Graphics Monitor Calibration Device on page 15 Network Connections on page 16 Connecting the Autodesk Control Surface to a Lustre Workstation on page 18 Connecting the Slave Renderer to a Lustre Workstation on page 19 Overview of Peripheral Connections The following diagram provides an
HP Z800 Workstation Power To keyboard, mouse, tablet, monitor calibrator To Lustre control surface To house network GigE Adapter to SAN and/or private network, Incinerator node Nvidia Quadro FX 5800 Atto Celerity FC84-EN to direct attached storage InfiniBand / 10-GigE Adapter to Wire network (optional) To graphics monitor AJA OEM-2K to video/audio i/o, VTR Nvidia Quadro SDI Output to reference monitor, RealTime Deliverables VTR, sync generator NOTE This diagram depicts the HP Z800 workstation with a 2
NOTE Although each end of the DVI cable appears to be identical, this is not the case. Ensure the connector labeled Computer is connected to the workstation. Connect the one labeled Monitor to the monitor. 3 Optionally, extend the monitor cable to a machine room using the DVI extender cable (DL.CAB-HDTV-FO82MM). Connecting the Keyboard, Mouse, and Tablet The keyboard, mouse and tablet connect to the workstation by way of the USB extender kit (TP.USB-EXT-410I).
Network Connections Network connections enable the workstation to gain access to a wide variety of possible networks. The Gigabit Ethernet (GigE) ports built-in to the workstation, and those provided by the add-on GigE adapter, can provide access to the following: ■ House network (e-mail, Internet, etc.
■ Link aggregation ( port bonding) switch, etc. NOTE Do not use any of the ports on the add-on network card for your house network. If the house network is not connected to the on-board network port, consult your system administrator to reconfigure it.
Connecting the Autodesk Control Surface to a Lustre Workstation The Autodesk Control Surface consists of three panels connected to the workstation’s on-board GigE port 1 by way of the supplied network switch. The central panel requires an additional connection to the remote unit of the USB extender kit. This section provides information on making the physical connections needed to operate the Autodesk Control Surface. For information on using the Control Surface, see the Autodesk Control Surface User Guide.
2 Use network cables to connect each panel to the available ports in the network switch. 3 Additionally, connect the Colour Grading panel to the remote unit of the USB extender kit. 4 Use a network cable to connect an available port on the Netgear network switch to the workstation, as illustrated. 5 Refer to the application installation and configuration guide for instructions on assigning an IP address to the Autodesk Control Surface.
20
Setting Up Video Hardware 4 Topics in this chapter: ■ ■ ■ Video Hardware Components on page 21 Connecting Video Components on page 22 Setting Up VTR Emulation on page 23 Video Hardware Components This chapter explains how to set up video I/O for your workstation. The following components are included in your shipment: Nvidia Quadro FX 5800 graphics adapter The Nvidia Quadro FX 5800 graphics adapter drives the LCD monitor directly, and a broadcast monitor via the Nvidia Quadro SDI Output adapter.
Connecting Video Components The following diagram illustrates how to connect the video hardware components included in your shipment. The only video hardware you must provide are a sync generator, VTR, HD/SDI-ready broadcast monitor and patch panel (if desired).
S y nG c en S y nG c en HP Z800 Video I/O from house sync generation (Trilevel/NTSC/PAL not included) SD/HD SDI In / Out to RS-422 VTR machine control SD/HD SDI In / Out AES/EBU Audio Video MonitorOut In Out Ch. 1/2 In Ch. 3/4 In Ch. 5/6 In Ch. 7/8 In Ch. 1/2 Out Ch. 3/4 Out Ch. 5/6 Out Ch. 1/2 Ch. 7/8 Out In Out Ch. 3/4 In Out Ch. 5/6 In Out Ch. 7/8 SDI 1/A Y/G/CVBS SDI 2/B AJA BOB (Front) K3-Box In 1/A In 2/B Out 1/A RS-422 Ch.1(L) Ch.
To configure hardware for VTR emulation: 1 Connect the video I/O cables between the devices involved in the VTR emulation process (out-to-in/in-to-out). Make sure the connections support the video standard you want to work with. If you intend to use the emulator as a Player, it is recommended that you connect one black or colour bar SDI signal to the input of the system serving as the VTR emulator. This ensures the Player is stable and correctly synced.
Setting Up Audio Hardware 5 Topics in this chapter: ■ ■ ■ ■ Overview of Audio Components on page 25 Wiring Audio Components on page 26 Configuring the Lucid ADA 88192 Converter on page 26 Audio Keywords in the Visual Effects and Finishing Configuration File on page 29 Overview of Audio Components Your application uses the Discreet Native Audio subsystem. Discreet Native Audio uses the following hardware components, shipped with your system. Lucid ADA 88192 Audio Converter audio I/O devices.
5 Set the appropriate keywords in the software initialisation file. See Audio Keywords in the Visual Effects and Finishing Configuration File on page 29 Wiring Audio Components The following diagram illustrates how to connect the Discreet Native Audio hardware components to the AJA breakout box. IN GPI RS 422A OUT RS 422C 1/2 3/4 Ch. 1/2 In WClk Ch. 3/4 In CVBS Ch. 5/6 In RS.422B Ch. 7/8 In RS.422D Ch. 1/2 Out Ch. 3/4 Out 7/8 1/2 3/4 In Out LTC Ch. 5/6 Out In Out In Out Ch. 3/4 Ch.
Understanding Remote vs. Local Control of the Lucid Converter You can control the converter either remotely or locally. Remote control of the converter means that you adjust converter settings through the audio preferences of the application. If you want to control the converter remotely, you must connect the converter to the serial port of the workstation. Local control means you adjust converter settings manually, using the controls on the front of the converter.
Lucid ADA 88192 Converter Settings for Remote Control You must configure the following settings to control the converter remotely. Any setting not listed here either has no effect with the application or can be set through the audio preferences of the application.
Menu Menu Item Comment For digital audio: AES INs --> ADAT OUTs AES INs --> AES OUTs AES INs --> ANALOG OUT Sync Internal OFFExternal AES 1+2 System Miscellany Route Unit: 8 External AES 1+2 is the recommended setting. Audio Keywords in the Visual Effects and Finishing Configuration File There are two keywords in the software initialisation file (by default, init.cfg) that must be uncommented and set to the correct values to ensure Discreet Native Audio works properly.
30
Connecting Storage 6 Topics in this chapter: ■ ■ ■ ■ Connecting Media Storage on page 31 Connecting the Fibre Channel Adapter on page 31 Connecting Storage Enclosures on page 32 Connecting Archiving Storage on page 39 Connecting Media Storage The workstation can be connected to two types of media storage. ■ Stone Direct XR-series disk arrays Autodesk's high-performance direct-attached storage (DAS) solution designed to address the different real-time playback requirements of various workflows.
The fibre channel adapter is equipped with four ports, called loops. You can connect your storage enclosure to the fibre channel cards using either 2 loops or 4 loops. A 2-loop device can be connected to either the inner pair of ports or the outer pair of ports. A 4-loop device requires both the inner pair and the outer pair.
A number of Stone Direct configurations will ensure optimal playback of the most demanding formats.
Connecting XR 6500 Storage The following diagrams illustrate 2-loop and 4-loops connections for XR 6500 series storage assemblies. Cable your storage exactly as illustrated to ensure proper functionality. A XR 6500 RAID enclosure supports a maximum of seven XE expansion enclosures. Configurations with two XR RAID enclosures are not supported. WARNING Do not power on your storage before installing Linux, otherwise the Red Hat installer might attempt to format the storage array and use it as the system disk.
Single XR 6500 RAID enclosure, 4 loops To FC adapter on workstation / LMS (port 0) To FC adapter (port 1) To FC adapter (port 2) To FC adapter (port 3) XR RAID Enclosure C A S HOST 1 HOST 0 8 4 1/2 0 I 8 4 1/2 0 I 8 4 1/2 8 4 1/2 HOST 1 C A S HOST 0 XE (EBOD) Expansion Enclosure 0 0 0 I 0 0 I 0 0 0 XE (EBOD) Expansion Enclosure 0 0 0 I 0 0 I 0 0 0 XE (EBOD) Expansion Enclosure 0 0 0 I 0 0 I 0 0 0 Cabling for additional enclosures NOTES: ■ In a 4-loop configuration, you need a
Connecting XR 6412 Storage The following diagrams illustrate 2-loop and 4-loops connections for XR 6412 series storage assemblies. A XR 6412 RAID enclosure supports a maximum of seven XE expansion enclosures. Configurations with two XR RAID enclosures are not supported. WARNING Do not power on your storage before installing Linux, otherwise the Red Hat installer might attempt to format the storage array and use it as the system disk.
Single XR 6412 RAID enclosure, 4 loops To FC adapter on workstation / LMS (port 0) To FC adapter (port 3) To FC adapter (port 1) To FC adapter (port 2) XR RAID Enclosure ! 0 FACTORY USE ONLY ! 0 FACTORY USE ONLY XE (EBOD) Expansion Enclosure 0 0 1 0 1 ID 0 ID XE (EBOD) Expansion Enclosure 0 0 1 0 1 ID 0 ID XE (EBOD) Expansion Enclosure 0 0 1 0 1 ID 0 ID XE (EBOD) Expansion Enclosure 0 0 1 0 1 ID 0 ID Cabling for additional enclosures NOTE In a 4-loop configuration with a X
Connecting XR 5402 and XR 5412 Storage The following digrams illustrate 2-loop and 4-loop connections for XR 5402 and XR 5412 series storage assemblies. XR 5402 and XR 5412 series storage assemblies support 2-loop configurations with one XR RAID enclosure, and 4-loop configurations with two XR RAID enclosures. WARNING Do not power on your storage before installing Linux, otherwise the Red Hat installer might attempt to format the storage array and use it as the system disk.
NOTE The XR 5402 and XR 5412 RAID enclosures support a maximum of four XE expansion enclosures.
While Autodesk Media and Entertainment makes no certification statement about any tape drive device, you can use the “Tape Drive Test” plug-in in Autodesk SystemCentral to test SCSI tape drives for compatibility. For more information, see the Autodesk System Central User Guide.
SCSI Tape Drive Devices | 41
42
7 Configuring the Workstation BIOS Topics in this chapter: ■ ■ ■ Checking the BIOS Settings on page 43 Updating your System BIOS on page 44 Restoring BIOS to Default Factory Settings on page 45 Checking the BIOS Settings After wiring the workstation and before installing Linux, turn the workstation on and check the BIOS version and BIOS settings. WARNING If BIOS settings are not set up correctly before installing Linux, you will need to reinstall the OS.
BIOS Menu Submenu Item Value USB Device Hard Drive Integrated SATA Power OS Power Management Runtime Power Management Disable Idle Power Saving Normal MWAIT Aware OS Disable ACPI S3 Hard Disk Reset Disable SATA Power Management Disable Intel Turbo Boost Technology Disable Processors Hyper-Threading Enable Chipset/Memory Memory Node Interleave Enable NUMA Split Mode Disable S5 Wake on LAN Disable Internal Speaker Disable NIC PXE Option ROM Download Disable
The directory contains an .iso disc image file for each supported BIOS version, as well as a README text file that describes each file, and provides information on updating the BIOS. 4 Burn the correct .iso file to a CD and place it in the DVD-ROM drive on the workstation. 5 Reboot your workstation and press F10 to enter the system BIOS. 6 Optional: Press F8 to select a language. 7 In the Storage menu, select Storage Options, and set SATA Emulation to IDE.
5 When the workstation reboots, press F10 again to re-enter the BIOS, and configure the recommended Autodesk settings.
A VTR Control Cable Pinouts Topics in this chapter: ■ ■ Standard VTR Control Cable Pinouts on page 47 VTR Emulation RS-422 Control Cables on page 48 Standard VTR Control Cable Pinouts The following diagram depicts the RS-422 control cable pinouts for the standard VTR control cable.
VTR Emulation RS-422 Control Cables Custom cables are required to control the VTR emulator. The pinouts required by the cable depend on the workstation and device involved in the VTR emulation process. The following diagrams depict the control cable pinouts required for the most common VTR emulation setups.
Index A documentation set adapters graphics 21 SDI 21 air conditioning requirements 9 AJA HD5DA. See video distribution amplifier AJA K3-Box. See video breakout box AJA OEM-2K board.
R RAID enclosures 32 RS-422 control cable 48 S SDI adapter 21 software initialisation file, audio keywords support contacting 2 T tablet, connecting 15 V video breakout box 50 | Index 21 29 video distribution amplifier 21 video hardware components 21 video I/O adapter 21 video I/O, wiring 21–22 video wiring 22 VTR connecting 22 control cable 47 emulation control cable 48 VTR emulation 23 W wiring video I/O and broadcast monitor 21–22 workflow, hardware setup and software installation workflows app
