Specifications

electrical systems
66
electrical systems
67
outline. When the battery is being charged then
this will display 100%.
LOW to 20% Flashing Red Screen
20% to 40% Red Screen
40% to 70% Yellow Screen
80%to100%GreenScreen
NOTE:BatteryLifewilldependonmanyfactors
so if the reading is at 50% or below then it is
advisable to charge the battery or to switch of
some of the items in the Motorhome so as to
reduce the Load on the Battery. If 2 Habitation
Batteries are fitted then when the Screen is
pressed from the first battery it will display the
Life of the Second battery.
The Display will automatically return to the
ONSCREENafter2Minutesapproxoryoucan
returntotheSYSTEMSSCREENbypressing
anywhere on the Screen.
HABITATION BATTERY STATUS SCREEN
TheHABITATIONSTATUSSCREENdisplays
the Status of the Habitation Battery (i.e. if the
battery is being charged or discharged). If the
battery is being charged then the Battery will
readCHARGEasabove,thescreenwillbe
green and the blocks on the side will go solid
depending on the amount of charge going into
the Battery. If the battery is being discharged
thentheBatterywillreadDISCHARGEthe
screen will be red and the blocks on the side
will go solid depending on the amount of
discharge going coming out of the Battery.
When the Screen will goes yellow and the
display shows neither Charge nor Discharge
in the Battery then this will indicate that the
Battery is Fully Charged or there no Load on
theSystem.NOTE:If2HabitationBatteriesare
fitted then when the Screen is pressed from
the first battery it will display the Status of the
Second battery.
The Display will automatically return to the
ONSCREENafter2Minutesapproxoryoucan
returntotheSYSTEMSSCREENbypressing
anywhere on the Screen.
The blocks on the side of the Display may
jump up and down slightly especially when
the charger has just been switched on this
will calm down as the voltage in the system
stabilizes and is quite normal.
INTERNAL TEMPERATURE SCREEN
TheINTERNALTEMPERATURESCREENdisplays
the Internal Temperature of the Motor Home.
TheScreenwillautomaticallyreturntotheON
SCREENafter2Minutesapproxoryoucan
returntotheSYSTEMSSCREENbypressing
anywhere on the Screen.
EXTERNAL TEMPERATURE SCREEN
TheEXTERNALTEMPERATURESCREENdisplays
the External Temperature. The Screen will
automaticallyreturntotheONSCREENafter2
Minutes approx or you can return to the SYSTEMS
SCREENbypressinganywhereontheScreen.
FRESH WATER LEVEL SCREEN
TheFRESHWATERLEVELSCREENdisplaysthe
Fresh Water Level in the Tank on the Motor
Home. There are five Levels.
FRESH WATER LOW Flashing Red Screen
FRESH WATER 25% Red Screen
FRESH WATER 50% Yellow Screen
FRESHWATER75%GreenScreen
FRESHWATER100%GreenScreen
TheScreenwillautomaticallyreturntotheON
SCREENafter2Minutesapproxoryoucan
returntotheSYSTEMSSCREENbypressing
anywhere on the Screen.
ALARM CLOCK SET SCREEN
TheALARMCLOCKSETSCREENallowsthe
Alarm Clock Time to be set.
Press the + or the – Symbol to achieve the
correct Hour and then press the Accept Symbol.
MINUTES press the + or the – Symbol to
achieve the correct Minutes and then press the
Accept Symbol.
Once the above has been entered then the
Display will return to the Systems Screen and
there will be a Tick underneath the Bell Symbol
on the On Screen. The Alarm Clock can be
cancelled by pressing the Bell Symbol. When
the Alarm is sounding it can be turned off by
pressing anywhere on the screen.
TheScreenwillautomaticallyreturntotheON
SCREENafter2Minutesapproxoryoucan
returntotheSYSTEMSSCREENbypressing
anywhere on the Screen.
CLOCK SET SCREEN
TheCLOCKSETSCREENallowstheTimeand
Date to be set and is done in the following order.
YEAR press the + or the – Symbol to achieve the
correct Year and then press the Accept Symbol.
MONTH press the + or the – Symbol to
achieve the correct Month and then press the
Accept Symbol.
DATE press the + or the – Symbol to achieve the
correct Date and then press the Accept Symbol.
DAY press the + or the – Symbol to achieve the
correct DAY and then press the Accept Symbol.
HOUR press the + or the – Symbol to
achieve the correct Hour and then press the
Accept Symbol.
MINUTES press the + or the – Symbol to
achieve the correct Minutes and then press
the Accept Symbol.
SECONDS press the + or the – Symbol to
achieve the correct Seconds and then press
the Accept Symbol.
Once all the above has been entered then the
Display will return to the Systems Screen.
TheScreenwillautomaticallyreturntotheON
SCREENafter2Minutesapproxoryouitwill
returntotheSYSTEMSSCREENaftersettingall
of the above.