RS-727LCD PROFESSIONAL 2-WAY LCD REMOTE CAR STARTER & ALARM SYSTEM With Built in Temperature sensor And Serial Port Data Link OPERATION MANUAL Please register your product at: www.autopageusa.
TABLE OF CONTENTS: A B C LCD REMOTE TRANSMITTER: BATTERY REPLACEMENT THE REMOTE LCD ICONS WITH FUNCTION PROGRAMMING OF THE LCD REMOTE TRANSMITTER 1. Screen Lamp ON 2. Power Save Mode 3. Clear The Flash Icon and Melody Sound 4. Stop The Melody Sound. 5. Button Lock 6. Vibration / Melody Mode 7. Enable / Disable Bi Sound While Pressing Button: 8. Low Battery Indication. 9. Set Up Fixed Count Down Timer 10. Out Of The Range Check D CLOCK & TIMER SETTING 1. Clock Setting. 2. Alert Alarm Timer Setting 3.
L M N CAR LOCATOR PANIC FUNCTION TRIGGER THE SYSTEM Clear The Trigger Icons and Melody Sound Stop The Melody Sound Only Noise Abatement Circuit O ANTI CAR- JACKING Active Anti Car Jacking Passive Anti Car Jacking Trigger The Anti Car Jacking Mode Override The System To Turn Off Anti Car Jacking P Q R S T U V W X SYSTEM’S TRIGGER CHECK SYSTEM’S STATUS CHECK DRIVER PAGING (OPTION) DOME LIGHT CONVENIENCE DELAY & SUPERVISION IGNITION CONTROL THE DOOR LOCK/UNLOCK TRUNK RELEASE (CHANNEL 3) OUTPUT CHANNEL 4 T
United States and is a wholly owned subsidiary of Iwata Electric Co., of Tokyo, Japan. Iwata has been an industry leader for over 50 years, establishing a reputation for ingenuity in its engineering capability and innovative communication products. Auto Page and Iwata maintain a long tradition of providing the best value to their customers. TRANSMITTERS The RS727 comes with two transmitters. The XT72LCD is a 2-way transmitter and receiver, also referred to as a transceiver.
WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. 2. 3. 4. 5. 6. 7. 8. 9. Keep the transmitter out of children’s reach. Do not leave anyone in the vehicle while running on remote control. Alert servicing personnel that the vehicle can be started automatically. Do not start the vehicle by remote while it’s in an enclosed area or garage. Always apply the parking brake and lock the vehicle as you exit the vehicle.
B. THE REMOTE LCD ICONS WITH FUNCTION: Door Lock Your vehicle doors are locked Door Unlock Your vehicle doors are unlocked and the system is Disarmed Armed Mode Your vehicle is in armed mode Valet Mode All the function shall be temporarily on hold.
C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER: Transmitter Button (1 second) (3 seconds) Description LCD screen lamp turns on for 5 seconds. Timer Programming Mode. Power Save Mode (5 seconds) - (2-second) (2-second) Clear the Flash Icon and Melody Sound on the LCD Screen Transmitter Button Lock ( ) enable / disable Melody / Vibration ( ) Mode Program Count Down Timer - (2-second) ( ) (10-Minute / 20M / 30 M - (2-second) Enable / Disable Bi Sound (Bi) While Pressing Button /1Hour /1.5H / 2.
6. Vibration / Melody Mode: This is useful when you are in a noisy place and it is difficult to hear the beep sound from the remote control. In this mode, the remote control vibrates itself if your security system is triggered. Press the button first, within 3 seconds press and hold ( ) button for 2 seconds to select the mode of vibration or melody, the icon will displayed on the LCD screen to show the LCD remote transmitter is on vibration mode. 7.
D. CLOCK & TIMER SETTING: Transmitter Button 1 Press & Hold button for 3 seconds 2 for + Time setting (Minute) *Flash digit for adjusting Alert Alarm Time Setting (Hour) *Flash digit for adjusting Alert Alarm Time Setting (Minute) *Flash digit for adjusting for – and for + for – and for + for – and for + button once Press button once. Press button once Press button once Alert Alarm Setting ON / OFF Press button once Count Down Timer Setting (Hour) *Flash digit for adjusting (Max.
3. Count Down Timer Setting: Example- Set the countdown timer at 2:30 button for 3 seconds, two-melodies will sound and the “Hours” 1. Press & hold the digit will flash for adjustment. button 5 times, the LCD screen will show the icon and the 2. Press the “Hours” digit flashes for adjustment. 3. Press or button to decrease or increase the “Hour” digit until 2:xx. 4. Press the button once again then the “Minutes” digit will flash for adjusting.
Trunk Release (Channel 3) Press and Hold for 2 seconds Passive Arming By-pass While the system Disarmed. Activate or Turn Off The Remote Start Press twice within 3 seconds. + II Channel # 4 Timer Output (4) Optional Switching code For 2nd Car Operation. For regular XT-65 remote transmitter Only B.
F. ALARM OPERATING CONDITION: 1. Arming Siren / Horn 1 or 3 Chirps Parking Light 1 Flash 2. Disarming 2 or 4 Chirps 2 or 3 Flashes 3. Trigger 4. Passive Starter Disable 5. Panic 6. Car-Jacking Alarming Flashes Alarming Alarming Flashes Flashes 7. Car Locator 6 Chirps 12 Flashes LED Slow Flash Doors Locking Starter Disable Unlocking Slow Flash Disable Fast Flash Disable Disable Dome Light Turns on for 30 -second Flashes Flashes Flashes Locking G. ACTIVE ARMING – LOCK & ARM: 1.
The vehicle doors will automatically lock after the passive arming cycle has been completed. PASSIVE ARMING BY-PASS: While the system is disarmed, Press the button twice, the system will respond with [1] chirp and LED will turn “ON”. The security system will remain in this temporary state for as long as you wish. To exit passive or buttons and the system will return to normal by-pass, press the transmitter status. I. ACTIVE DISARMING – UNLOCK & DISARM: 1. Press button on the transmitter. 2.
2. Within 5 seconds, enter your chosen first digit code by pressing and releasing the Valet Switch. (When finished above procedures, system's siren will stop alarming, lights will stop flashing, but the vehicle can’t be started.) 3. Within 15 seconds of the last digit code enter (the 1st code), then turn the Ignition Switch “OFF” and then “ON”. 4. Within 15 seconds, enter your chosen second digit code by pressing and releasing the Valet Switch. 5. Turn the ignition switch “OFF” position.
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency. 1. Press and hold the button for 3 second. The alarm will immediately sound. 2. During panic mode, the normal function of this transmitter button will be disabled. The transmitter and buttons can be used to lock and unlock the door (if the option is installed), however once the button is pressed, the vehicle’s starter disable device, (where installed) will be disengaged allowing the vehicle to start. 3.
“Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for six full cycles, the doors will be bypassed until the trigger ceases. O. ANTI CAR- JACKING Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature “OFF”. This system is default setting all car jacking “OFF”. ACTIVE ANTI CAR JACKING: 1. Press and hold the transmitter and buttons at the same time for 2 seconds while the vehicle’s ignition is ON.
In Car Driver Paging With the ignition in the switched “off” condition, press and hold the valet switch for 2 seconds to page the driver. One chirp sound will be emitted from the vehicle and the paging melody sound will continue sounding from your Remote LCD Transmitter and the “ ” icon will flash on the LCD screen.
or sunroof. (Factory defaults setting at momentary output.) W. POWER ON MEMORY: This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected. X. SECOND VEHICLE SECURITY OPERATION: Your 5-button remote transmitter can be utilized to control a second vehicle security system, To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming.
vehicle security system. It has one short “bi” sound while pressing the button of the LCD screen transceiver. REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: When you want to start your vehicle, button once on the transmitter. 1. Press 2. The parking light will activate to indicate the remote start received the signal. 3. The engine will start in approximately 5 seconds. 4.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. C. TEMPORARY STOP FEATURE: This feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate control on. 1.
4. Press the brake pedal to stop the vehicle running. Exit the timer start: Timer start can be exited manually as follows: 1. Make sure the remote start system is not operating the engine. 2. Turn the ignition on. The LED and parking light will flash (4) times. The horn chirps (4) times. Or 1. Press the button twice to remote start the vehicle. As soon as the vehicle is running and the parking light have turned on or flashing. 2. Immediately depress the button then press and hold the button for 2 seconds.
I. DISABLING THE REMOTE START SYSTEM: (If installed) This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position. LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. ,Continental U.S. and Canada Only) 1. Auto Page, Inc.
indirectly from the use or presence of the equipment or parts; Consequential damages of any kind; any inability of the purchaser to use the equipment. **IMPORTANT NOTE: Any damages to the alarm system resulting from an installation performed by anyone other than a professional installation technician authorized by a dealer of Auto Page will void the product’s limited lifetime warranty. Auto Page Warranty: You must register your product online at http://www.autopageusa.com to receive any warranty service.
960 Knox Street Unit B, Torrance, CA 90502 24
Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.
