RF-520LCD 2-WAY AM/AM LCD COMMUNICATION PROFESSIONAL VEHICLE SECURITY SYSTEM OPERATIONS MANUAL
TABLE OF CONTENTS Introduction Changing Battery XT-72S Standard Transmitter Remote Transmitter Operation LCD Transmitter Operation Button Lock LCD Transmitter LED Display Chirp Indicators Parking Light Flashes Alarm Operation Condition Active Arming Ajar Warning Silent Arming Shock Sensor By-pass Hidden Alarm Passive Arming Passive Arming By-pass Active Disarming Tamper Disarming Pathway Illumination 2 Step Unlock Automatic Rearm Disarm without Transmitter Valet Enter & Exit Valet Mode Car Locator Panic Fun
Congratulations on your purchase of the RF520LCD vehicle security system. We sincerely hope the purchase of the RF520 security system gives peace of mind to you. The RF520 LCD is a state-of-the-art two-way communication system. Please take the time to read over this manual to thoroughly familiarize your self with the many features and options of the RF520. Auto Page, Inc.
WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. 5. Always apply the parking brake and lock the vehicle as you exit the vehicle. 6.
LCD DISPLAY TRANSMITTER OPERATION ONLY: Transmitter Button - (C) - - (C) (1 second) - Remark System’s Trigger Check Press within 3 seconds System’s Status Check Press within 3 seconds LCD screen lamp turns on + System Function (2 sec) for 5 seconds.
ALARM OPERATING CONDITION: Siren / Horn 1 or 3 Chirps 2 or 4 Chirps Parking Light LED Doors Starter 1 Flash Slow Flash Locking Disable 3. Trigger Alarming Flashes 4. Panic Alarming Flashes 5. Car Locator 6 Chirps 12 Flashes 1. Arming 2. Disarming 2 or 3 Flashes Unlocking Slow Flash Dome Light Turns on for 30 -sec Disable Flashes Flashes Locking ACTIVE ARMING – LOCK & ARM: 1. 2. Press button on the transmitter.
PASSIVE ARMING Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows. 1. Turn the ignition to the “OFF” position and exit the vehicle. 2. After all entrances are closed, the security system LED will flash fast for 30 seconds.
TWO STEPS DOOR UNLOCK: This feature will independently unlock the driver’s door only when disarming the security system. Pushing the button a second time within 3 seconds will unlock the other doors. AUTOMATIC RE-ARM : If this feature is selected, the security system will automatically re-arm itself in 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.
TRIGGER THE SYSTEM When armed, your vehicle is protected as follows: 1. Light impact will trigger the warn-away signal. 2. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the ignition key will trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking lights, and dome light will turn on to alerting of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm.
SYSTEM’S STATUS CHECK (For two-way transceiver operation only) When you want to check the system’s present status through the LCD screen, Press the transceiver button twice, within 3 seconds press (C) button. It responds with one melody sound, the LCD screen should be illuminated. Note: If it has no responds then you are out of range. DRIVER PAGING (For two-way transceiver operation only) It is useful the event that someone wants to page the driver of the parked vehicle.
CHANNEL 5 AUXILIARY CONTROL OUTPUT (Available Option) Press the transmitter + button to active Channel 5 function. Channel 5 is a programmable output. This feature, when installed with optional accessories, may be used to operate power windows, sunroofs, etc. from your remote transmitter. CHANNEL 6 AUXILIARY CONTROL OUTPUT (Available Option) Press the transmitter + button to active Channel 6 function. Channel 6 is a programmable output.
LCD REMOTE CONTROL TRANSCEIVER: Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power or such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low out put powered frequency. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen.
Door Open Warning Doors are illegally opened (Zone 3) Trunk/Hood Trigger Trunk or Hood is illegally opened (Zone 2) Shock Sensor Trigger Trigger on Shock Sensor (Zone 4) Warn Away trigger Trigger on Shock Sensor (Zone 1) Alert Alarm You have set morning call alarm Power Save Mode Save the battery power Time Monitor Count Down Timer Reminder when time is up for parking Vibration Mode Remote Control vibrates when the system is triggered Driver paging Someone is paging you in front of your vehicle Button
Screen Lamp ON: Press and hold the button one second, with one melody sound and the LCD screen lamp will turns on for 5 sec. Power Save Mode: While the power save mode, the LCD remote transceiver uses “0” current to save the battery power. Entry: Press & hold the button for 5 seconds, with one melody sound and icon on the LCD screen to indicate entry the “power save mode”. Exit: Press any button of the LCD remote transmitter to exit the “Power Save Mode”.
Set Up Fixed Count Down Timer: 1. Press the button first, within 3 seconds press and hold the two seconds, the LCD screen will shows ( ) button for icon and timer (ie. 0:10), 2. Press the ( ) button again showing next order time on the screen ( ie.0:20), press them again (ie.0:30)…..and so on. 3. Leave the buttons starting count down then icon flashes Note: 1. The count down period is fixed as 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5 hours and 2 hours maximum. 2.
Timer Setting: Example to AM10:30 1. Press & hold the button for 3 seconds, with two-melody sound and the “Hours” digit flashes for adjusting. 2. Press the or button to decrease or increase the “Hour” digit until AM10: xx 3. Press the button once again then the “Minute” digit flashes for adjusting. 4. Press the or button to decrease or increase the “Minutes” digit until AM 10:30 5. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode.
LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. and Continental U.S. Only) 1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery. Your AutoPage equipment is guaranteed for “life” to the original purchaser/user of the equipment under the following conditions: If the product proves defective (according to AutoPage’s testing) within the first year, the defective unit may be exchanged or repaired free of charge.
This WARRANTY CARD is for your record. However, AutoPage reserves the right to request you to submit this WARRANTY CARD, which must have complete information to receive warranty service. Please keep this card in a secured place . AUTOPAGE WARRANTY SERVICE CARD Model: ______________ Serial # _______________ CUSTOMER TO COMPLETE DEALER TO COMPLETE Mr./Mrs./Ms.
1815 West 205th Street Suite 101 Torrance, California 90501-1525 Main Office: 310-618-2002 Customer Service: 800-262-2527 Ext. 462 www.autopageusa.
