ELECTRONIC CASH REGISTER ER-900/SPS-300 SERIES SERVICE Manual ER-900/SPS-300 SERIES CONTENTS 1. Precaution Statements 2. Product Specifications 3. Installation and Operation 4. Disassembly and Assembly 5. Maintenance and Adjustment 6. Troubleshooting 7. Exploded Views and Parts List 8. PCB Layout and Parts List 9. Wiring Diagram 10. Bock Diagram 11.
Overview of this ECR System This service manual provides the technical information for many individual component systems and circuits and gives an analysis of the operations performed by the circuits. Schematics and specifications provide the needed information for the accurate troubleshooting. All information in this manual is subject to change without prior notice. Therefore, you must check the correspondence of your manual with your machine.
About this Manual This service manual describes how to perform hardware service maintenance for the SAM4S ER-900/SPS-300 SERIES Notes Notes may appear anywhere in the manual. They describe additional information about the item. Precaution symbols . Indicates a Safety Precaution that applies to this part component. . Indicates the part or component is an electro-statically sensitive device. Use caution when handling these parts.
Copyright ⓒ 2011 by Shin Heung Precision. All right reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable from without prior written permission of Shin Heung Precision . SAM4S ER-900/SPS-300 SERIES Oct. 2011. V1.
1 Precaution Statements Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1. Be sure that all built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including nonmetallic control knobs and compartment covers. 3.
1 Precaution Statements 1-2 Servicing Precautions WARNING: First read the-Safety Precautions-section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. WARNING: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2.
2 Product Specifications [ SPS-300 PART ] Specifications are correct at the time of printing. Product specifications are subject to change without notice. See below for product specifications.
2 Product Specifications [ ER-900 PART ] Specifications are correct at the time of printing. Product specifications are subject to change without notice. See below for product specifications.
2 Product Specifications 2-2 Appearance 2-2-1 Appearance Dimensions (mm) Figure2-1 Dimensions 2-2-2 Location Features 1 5 2 6 7 8 9 3 4 ① Printer Cover ② Key Board ③ Dallas Key (i-BUTTON) ④ Drawer ⑤ Customer Display(9 Digit LED) ⑥ Operator LCD Display(2line 16char LCD or 192X 64 Graphic LCD) ⑦ Mode Key ⑧ Power Switch ⑨ MSR Figure2-2 Location Features SAM4S ER-900/SPS-300 SERIES 2-3
2 Product Specifications 2-3 Thermal Printer Specifications 2-3-1 Printer Specification (With Cutter) Item Description Model • CAPD245 Print Method • Thermal Line Printing Total Number of Dots Printing Format Dot Pitch SII • 384 Dots / I Line • Vertical : 0.125 mm • Horizontal : 0.125 mm Printing Speed • 85 mm/Sec Printing Direction • Unidirectional Friction Feed Paper Feeding Power Supply Volt Feeding Method • Friction Feed Minimum Feed Pitch • 0.
2 Product Specifications 2-3 Thermal Printer Specifications 2-3-2 Paper Specification Item Description Paper Type • Single-ply Thermal Paper Roll Paper Size • 58.0 +0/-1mm (Width) ×80 mm or less Specified Paper • Original Paper No : HPK-110 (Hansol paper XT) Remark Table2-4 Paper Specification Note: The following paper can be used instead of the specified paper above. TF50KS-E2D: Nippon paper industries Co.,Ltd. PD 160R-63 : New Oji paper Mfg, Co.,Ltd.
2 Product Specifications 2-3 Thermal Printer Specifications 2-3-1 Printer Specification (Without Cutter) Item Description Model • LTPD245 Print Method • Thermal Line Printing Total Number of Dots Printing Format Dot Pitch SII • 384 Dots / I Line • Vertical : 0.125 mm • Horizontal : 0.125 mm Printing Speed • 85 mm/Sec Printing Direction • Unidirectional Friction Feed Paper Feeding Power Supply Volt Feeding Method • Friction Feed Minimum Feed Pitch • 0.
2 Product Specifications 2-3 Thermal Printer Specifications 2-3-2 Paper Specification Item Description Paper Type • Single-ply Thermal Paper Roll Paper Size • 58.0 +0/-1mm (Width) ×80 mm or less Specified Paper • Original Paper No : HPK-110 (Hansol paper XT) Remark Table2-7 Paper Specification Note: The following paper can be used instead of the specified paper above. TF50KS-E2D: Nippon paper industries Co.,Ltd. PD 160R-63 : New Oji paper Mfg, Co.,Ltd.
2 Product Specifications 2-4 Power Specifications 2-4-1 Power Specification Item Description Remark Input Voltage & • U.S.A : AC 120V, 60Hz,0.3A (Min : 102V, Max : 138V) Current • Europe : AC 230V, 50Hz,0.16A (Min : 195.5V, Max : 264.5V) Power Consumption • Peak Output Voltage • AC 20V 3.
2 Product Specifications 2-5 Interface Specifications 2-5-2 RS-232C Signal Description PIN NO DSUB9(CN1) Signal Name Direction Function RJ45(CN3) 1 - DCD IN Carrier Detect 2 4 RXD IN Receive Data 3 3 TXD OUT Transmit Data DTR OUT Data Set Ready GND - DSR IN 4 5 7 6 Data Terminal Ready 7 8 RTS OUT 8 2 CTS IN Clear To Send RI IN Ring Indicator +5V/500mA - 9 1 Request To Send Total Power : 1A (COM#1,#2 : Pin9, COM#3 ,#4 : Pin1 ) SAM4S ER-900/SPS-300 SERIES 2-9
2 Product Specifications 2-5 Interface Specifications 2-5-3 RS-232C Interface Cable 15m SPS-300/ER-900 SIDE (DSUB9 FEMALE) USER SIDE (DSUB25 MALE) (+5V) (COM1, COM2 I/F CABLE PIN CONNECTION ) 15m SPS-300/ER-900 SIDE (DSUB9 FEMALE) USER SIDE (DSUB9 MALE) (+5V) ( COM1, COM2 I/F CABLE PIN CONNECTION ) CAUTION : COM#1~COM#2 supplies “+5V” to DSUB9 “Pin Num 9”.
2 Product Specifications 2-5 Interface Specifications 2-5-3 RS-232C Interface Cable 15m SPS-300/ER-900 SIDE (RJ-45) 4(RXD) 3(TXD) 2(DSR) 7(S.GND) 8(DTR) 5(RTS) 6(CTS) 2(RXD) 3(TXD) 4(DTR) 5(S.GND) 6(DSR) 7(RTS) 8(CTS) USER SIDE (DSUB9 MALE) ( COM3, COM4 I/F CABLE PIN CONNECTION ) 15m SPS-300/ER-900 SIDE (RJ-45) 4(RXD) 3(TXD) 2(DSR) 7(S.GND) 8(DTR) 5(RTS) 6(CTS) 3(RXD) 2(TXD) 20(DTR) 7(S.
2 Product Specifications 2-5 Interface Specifications 2-5-4 USB Interface Specification Item Description Transfer Type Remark ● BULK ● Bi-Direction, Half-Duplex Data Signal ● Differential Signal Pair (D+ / D-) ● NRZI Format Data Format ● Zero Bit Stuffing after 6 Ones Transceiver ● Differential Common Mode Range : 0.8 ~ 2.5[V] ● Differential Receive Sensitivity : 200[mV] ● Single End Receive Threshold : 0.8 ~ 2.
2 Product Specifications 2-5 Interface Specifications 2-5-7 LAN (IRC) Signal Description Pin No Signal Name Signal Direction Function 1 ENET TX+ OUT Ethernet Transmit Data Line(+) 2 ENET TX- OUT Ethernet Transmit Data Line(-) 3 ENET RX+ IN Ethernet Receive Data Line(+) 4 N.C - 5 N.C - 6 ENET RX- IN 7 N.C - 8 N.C - Ethernet Receive Data Line(+) 2-5-8 LAN (IRC) Interface Cable MAX 100M SPS-300 /ER-900 SIDE 1(ENET TX+) 2(ENET TX-) 3(ENET RX+) 4(N.C) 5(N.C) 6(ENET RX-) 7(N.
2 Product Specifications 2-5 Interface Specifications 2-5-9 DRAWER Signal Description Pin No Signal Name Direction 1 S.G - 2 DRAWER#OUT OUT 3 DRACOMP IN 4 +24v - 5 DRAWER#OUT OUT 6 F.G - Function Signal GND Drawer Kick-Out Driver Signal. Drawer Open / Close Signal Supply DC +24[V] Drawer Kick-Out Driver Signal. Frame GND CAUTION : Make sure that installed “+24V Cash Drawer”.
3 Installation and Operation 3-1 System Configuration 3-1-1 Configuration Figure 3-1 System Configuration SAM4S ER-900/SPS-300 SERIES 3-1
3 Installation and Operation 3-2 Installation 3-2-1 Options No. Item Description 1 Dallas Key 5EA, 10EA, 15EA 2 Water Proof 3 Memory 4 MSR 1Slot 5 Interface RS-232*2, RS-232&USB Remark Selectable RAISED 63KEY, RAISED 91(98) KEY : Option FLAT 150KEY : Default SRAM 4Mb or 16Mb Table 3-1 Option 3-2-2 Supplies No.
3 Installation and Operation 3-3 Installation 3-3-1 Paper Roll Installation (1-Station) 1. 2. 3. 4. 5. Remove the cover printer.(Fig 3-2(A)) Push up the green lever toward and then lift up to open the paper cover. (Fig 3-2(B)) Ensure that the paper is being fed from the bottom of the roll. (Fig 3-2(C)) Close the paper cover slowly until it locks firmly.(Fig 3-2(D)) Passing the leading edge of the paper through the cutter slot. Tear off the excess paper.
3 Installation and Operation 3-3 Installation 3-3-2 Take-Up Spool Installation (1-Station) 1. 2. 3. 4. 5. 6. 7. 8. Before using the PRINTER. Install the TAKE-UP SPOOL as described in the figure. Push up the green lever toward and then lift up to open the paper cover. Unroll the paper about 400mm. Ensure that the paper is being fed from the bottom of the roll. Place the roll into the concave bottom of the PRINTER as shown in Figure3-2(C).
3 Installation and Operation 3-3 Installation 3-3-3 Paper Roll Installation (2-Station) 1. 2. 3. 4. 5. Remove the cover printer.(Fig 3-4(A)) Push up the green lever toward and then lift up to open the receipt paper cover. (Fig 3-4(B)) Ensure that the paper is being fed from the bottom of the roll. (Fig 3-4(C)) Close the paper cover slowly until it locks firmly.(Fig 3-4(D)) Passing the leading edge of the paper through the cutter slot. Tear off the excess paper.(Fig 3-4(E)) 6.
3 Installation and Operation Figure 3-4 Paper Installation (2-Station) 3-3 Installation 3-3-4 Take-Up Spool Installation (2-Station) 1. 2. 3. 4. 5. 6. 7. 8. Before using the PRINTER. Install the TAKE-UP SPOOL as described in the figure. Push up the green lever toward and then lift up to open the paper cover. Unroll the paper about 400mm. Ensure that the paper is being fed from the bottom of the roll. Place the roll into the concave bottom of the PRINTER as shown in Figure3-4(G).
3 Installation and Operation Figure 3-5 Spool Installation (2-Station) 3-3 Installation 3-3-5 Installation of MSR Assembly Caution : · Before installation, be sure to turn off the power switch. · Use gloves to protect your hand from being cut by the angle and the chassis. · Connect all the cables correctly. When connecting or disconnecting the cables, be careful not to apply stress to the cables. (It may cause disconnection) · Be careful not to bind interface cables and AC power cord together.
3 Installation and Operation 3-3 Installation 3-3-5 Installation of MSR Assembly 1 -○ a . 3. Connect Ground Wire & MSR Harness of MSR Assembly to the main set as shown in Figure 3-7-○ 4. Tidy up the connectors of Ground Wire & MSR Harness by inserting them into the MSR Assembly 1 -○ b . (Connectors should be hidden inside the MSR Assembly), Figure 3-7-○ 2 , Figure 3-5-○ 3 . 5. Insert MSR Assembly into the main set bracket holes as in Figure 3-7-○ 4 6.
3 Installation and Operation 3-3 Installation 3-3-5 Installation of MSR Assembly 1.
3 Installation and Operation 3-3 Installation 3-3-6 Installation of Interface Option Board Caution : · Before installation, be sure to turn off the power switch. · Use gloves to protect your hand from being cut by the angle and the chassis. · Connect all the cables correctly. When connecting or disconnecting the cables, be careful not to apply stress to the cables. (It may cause disconnection) · Be careful not to bind interface cables and AC power cord together.
3 Installation and Operation Figure 3-9 Interface Option Board Installation 3-4 Operation Note: Before using this ECR for the first time, leave it powered ON in the REG mode for at least 24 hours. This allows the Li-MH battery, which maintains the ECR memory while the power is OFF, to fully charge. 3-4-1 Mode Switch The position of the Mode Switch determines the action of the ECR.
3 Installation and Operation 3-4 Operation 3-4-2 All Clear This step insures that the cash register is cleared of any totals or programming. After this procedure, the cash register is ready for programming and operation. WARNING: This is a one time procedure. Do not repeat this procedure after the cash register is Programmed. It causes all programs and totals to be erased and to be default. 1. Turn off the power. 2.
4 Disassembly and Assembly Caution : · Before installation, be sure to turn off the power switch. · Use gloves to protect your hand from being cut by the angle and the chassis. · Connect all the cables correctly. When connecting or disconnecting the cables, be careful not to apply stress to the cables. (It may cause disconnection) · Be careful not to bind interface cables and AC power cord together. 4-1 Disassembling the Case Upper Block 4-1-1 Ass’y Case Upper 1.
4 Disassembly and Assembly 4-1-6 Ass’y KBD(63KEY, 91KEY, 150KEY) 1. Separate the ASS'Y CASE UPPER(C) from the ASS'Y CASE LOWER(F). (Page7-1) 2. Remove the ten screws(C17) from ASS’Y KBD(D). (Page7-1) 3. Separate the FPC(g) in ASS'Y SWITCH ROTARY(C16) from ASS'Y KBD(D). (Page7-6) 4. Separate the ASS’Y KBD(D) from PMO-CASE UPPER(C).
4 Disassembly and Assembly 4-2 Disassembling the Case Lower Block 4-2-1 Ass’y Supply (1-Station, Without A/C) 1. Open the ASS'Y COVER PRINTER(A) and lift it off. (Page7-1) 2. Separate the ASS'Y CASE UPPER(C) from the ASS'Y CASE LOWER(F). (Page7-1) 3. Remove the three screws(E22,E32) and then separate the ASS'Y Supply(E23) from the ASS’Y CASE LOWER(F). (Page7-14,22) 4. Separate a FPC(j) of printer and a cable(bb from Main Board(F6). (Page7-14) 5. Separate the ASS'Y Supply(E23) from the ASS'Y CASE LOWER(F).
4 Disassembly and Assembly 4-2 Disassembling the Case Lower Block 4-2-6 Ass’y Printer(1-Station/ 2-Station, Without A/C) 1. Open the ASS'Y COVER PRINTER(A) and lift it off. (Page7-1) 2. Separate the ASS'Y CASE UPPER(C) from the ASS'Y CASE LOWER(F). (Page7-1) 3. Push up the KNOB-RELEASE (E3) and then open the HOUSING CLAM_2M(E6). (Page7-14) 4. Remove two screws(E9) from the PMO-HOLDER PRINTER(E10). (Page7-14) 5. Remove a screw(E7) from the Printer(E8) and then remove the FPC(pp) from the JOINT-Board(E14).
5 Maintenance and Adjustment 5-1 Maintenance 5-1-1 Cleaning the Printer Head Paper dust on the heating elements may lower the print quality. In this case, clean the print head as follows: After printing, the printer head can be very hot. Be careful not to touch it. Also let it cool before you clean it. Do not damage the printer head by touching it with your fingers or any hard object. 1. Turn the ECR System power switch off. 2. Open the Printer Cover. 3.
5 Maintenance and Adjustment MEMO 5-2 SAM4S ER-900/SPS-300 SERIES
6 Troubleshooting 6-1 System power-up sequence The following lists the chain of events that occur when you turn on the ECR. You can follow this list as one means of determining if the ECR is operating correctly. When the power switch is turned on, these events occur: 6-1-1 Main B’D power-up sequence All devices (CPU, Memory, Controller…etc,) are reset. The power ( 3.3V,5V) LED are light on MAIN B’D. The boot/Application program (A29L1600UV) is run Now, Front-LCD & Rear-FND is displayed.
6 Troubleshooting 6-3 MAIN B’D Problem (System boot & program) 6-3-1 PGM Flash ROM (A29L1600UV) problem of Main B’D Related RESET → Check the reset IC (AME8500, U5) & reset time (150 ~ 270ms).. → Check related circuit & component whether short or not Related System signals (Address, Data, nCE, nOE, nWE) → Check these signals whether it short / open. Related System Clock → Check the crystal, if it operates correctly or not. → Clock frequency is 12MHz.
6 Troubleshooting 6-4-4 Data memory problem (Back-up broken when power off) The System-ECR has 4Mb or 16Mb SRAM and power fail sensing circuit for the data back-up. When power off, the MCU (LPC2470) detect a point of time and perform the data back-up. Check backup circuit on Main B’D → Check BAT43WS (D3,D4) and related component whether short or not. → Check battery voltage whether above 1.8V or not. → Check battery whether it is separated from battery socket.
6 Troubleshooting 6-5 MAIN B’D Problem (LAN, USB, Serial) 6-5-1 LAN Cable NOT attached (Green LED of LAN connector does not turn on). → Check LAN cable. Refer to chapter 2 cable connection diagram. → For IRC (Inter Register Communication), It has to be used the cross cable. → For LAN, It has to be used the direct connection cable. → Check LAN RJ-45 modular jack insert right position.. → Check the connection. Between I/F B’D and LAN Option B’D and Main B’D.
6 Troubleshooting 6-6 Main B’D problem (Thermal Printer, Feed motor, Auto-cutter) 6-6-1 Thermal Printer problem Print Operation Fail → Check the harness between Printer Joint B’D and Main B’D, if it is connected or not. → Check the harness between Printer Joint B’D and Printer Module, if it is connected or not. → Check the TPH voltage.(VPH=+8.5V), → Check the Control Signal on micom (data, clk, latch, strobe) → Check the Thermister of printer. → Check the ADC port of micom.
6 Troubleshooting 6-7 Main B’D problem (Key Board, Mode key, Drawer, MCR, Dallas-key) 6-7-1 Key Board & Mode Key Key Board Operation Fail → Check the FPC harness between Key Board and Main B’D. → Check the key scan part (74LVC138, U21, U23, U24) and key return part(74LVC541, U28). → Change the Key Board Ass’y → Check related circuit & component whether short or not. Mode key Operation Fail → Check the harness between Key Board and Main B’D. → Check the harness between Key Board and Mode Key Assy.
7 Exploded View and Parts List 7-1 Main Set 7-1-1 Exploded View (SPS-300 Series) Figure7-1 Total Disassembly (SPS-300 Series) SAM4S ER-900/SPS-300 SERIES 7-1
7 Exploded View and Parts List 7-1 Main Set 7-1-1 Exploded View (ER-900 Series) Figure7-2 Total Disassembly (ER-900 Series) 7-2 SAM4S ER-900/SPS-300 SERIES
7 Exploded View and Parts List 7-1 Main Set 7-1-2 A. ASS’Y-COVER PRINTER Figure7-3 ASS’Y-COVER PRINTER 7-1-2 A. ASS’Y-COVER PRINTER No. 1 2 Parts No.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 B. ASS’Y LCD (192X64 GRAPHIC LCD) Figure7-4 ASS’Y LCD ( 192X64 GRAPHIC LCD) 7-1-2 B. ASS’Y LCD(192X64 GRAPHIC LCD) No. Parts No. Serviceable Remark B JK96-10365A ELA-LCD 192 X 64 1 Y Without B7,B8,B9 1 JK72-20450A PMO-REAR LCD_L 1 Y 2 JK70-50125A SCREW-MACHINE:PH,M3,L8 2 Y 3 JK75-20063C MEC-HINGE ASS'Y 1 Y 4 JK70-50012A SCREW-TAPPING*PH,+,M2.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 B. ASS’Y LCD (2 LINE LCD) Figure7-5 ASS’Y LCD (2 LINE LCD) 7-1-2 B. ASS’Y LCD(2 LINE LCD) No. Parts No.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 C.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 C. ASS’Y-CASE UPPER No. 1 Parts No.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 D.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 D. ASS’Y-KEYBOARD (63KEY) No. D Parts No.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 D.
7 Exploded View and Parts List Figure7-8 ASS’Y KEYBAORD (91 or 98 KEY) 7-1 Main Set 7-1-2 D. ASS’Y-KEYBOARD (91 or 98KEY) No. D Parts No.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 D.
7 Exploded View and Parts List Figure7-9 ASS’Y KEYBAORD (150KEY) 7-1 Main Set 7-1-2 D. ASS’Y-KEYBOARD (150KEY) No. D Parts No. JK75-20132A Description / Specification UNIT-KEYBOARD_150 25 JK73-20225A REX-WATER PROOF 1 26 JK68-40204A LABEL(P)-KBD SHEET 1 Y 27 JK72-20471A PMO-KBD HOUSING_150 1 Y 28 JK73-20222A RMO-CONTACT RUBBER_150 1 Y 29 JK70-20186A FPC ASSY_150 1 Y 30 JK70-20183A IPR BOTTOM PLATE_150 1 Y 31 JK81-20005A SCREW-TAPPING:BH,+,2,M2.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 E.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 E. ASS’Y-PRINTER (1-STATION : MANUAL) No. Parts No. Description / Specification Q`ty Design-Location Serviceable E JK96-10370B ELA-UNIT-PRINTER_21M 1 Y 1 2 JK68-40189A JK70-50076A LABEL(P)-GUIDE SCREW-TAPTITE:RH,Ø8,M2.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 E.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 E. ASS’Y-PRINTER (1-STATION : A/C) No. Parts No. E JK96-10370A ELA-UNIT-PRINTER_21A 1 Y 1 JK68-40189A JK70-50076A LABEL(P)-GUIDE SCREW-TAPTITE:RH,Ø8,M2.6,L6 1 2 Y 13 6002-000175 SCREW-TAPPING:PWH,+,2,M3,L8 1 Y 14 JK92-01702J PBA SUB 1 Y 15 JK39-50005A CABLE-FFC: 30P,1.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 E.
7 Exploded View and Parts List Figure7-12 ASS’Y-PRINTER (2-STATION : MANUAL) 7-1 Main Set 7-1-2 E. ASS’Y-PRINTER (2-STATION : MANUAL) No. Parts No. E JK96-10369B ELA-UNIT-PRINTER_22M Description / Specification Q`ty 1 Design-Location Serviceable Y 1 2 JK68-40189A JK70-50076A LABEL(P)-GUIDE SCREW-TAPTITE:RH,Ø8,M2.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 E.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 E. ASS’Y-PRINTER (2STATION : A/C) No. Parts No. Description / Specification Q`ty Design-Location Serviceable E JK96-10369A ELA-UNIT-PRINTER_22A 1 Y 1 2 JK68-40189A JK70-50076A LABEL(P)-GUIDE SCREW-TAPTITE:RH,Ø8,M2.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 F.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 F. ASS’Y-CASE LOWER No. 1 Parts No. JK39-50005A Description / Specification CABLE-FFC;30P,1.0mm,150mm Q`ty 1 Design-Location Serviceable Y Remark 1-ST(E15) 2-ST(E34) JK39-50010A CABLE-FFC;30P,1.0mm,90mm 2 Y 2 JK39-50008A CABLE-FFC;24P,1.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 F. ASS’Y-CASE LOWER No. Parts No.
7 Exploded View and Parts List 7-1 Main Set 7-1-2 G. ASS’Y-MSR Figure7-15 ASS’Y MSR 7-1-2 G. ASS’Y-MSR No. G Parts No. MCR-901(STD) MCR-902(STD) 1 JK70-50012A 2 JK39-40758B JK48-00006B JK48-00005A 3 Description / Specification ELA-MSR : TRACK 1/2 Q`ty 1 Design-Location Serviceable Y ELA-MSR : TRACK 2/3 1 Y SCREW-TAPPING*PH,+,M2.
7 Exploded View and Parts List 7-2 G-DRAWER 7-2-2. H. ASS’Y-DRAWER (G-DRAWER:4B8C,5B5C) A.ASS’Y BILLCOIN (4B8C) A.ASS’Y BILLCOIN (5B5C) B.ASS’Y HOUSING C.ASS’Y LOCK E.ASS’Y TRAY D.
7 Exploded View and Parts List 7-2 DRAWER 7-2-2. H. ASS’Y-DRAWER (G-DRAWER:4B8C,5B5C) Figure 7-17 Lubrication Points of the G-Drawer(4B8C,5B5C) No. Code No.
7 Exploded View and Parts List 7-2 DRAWER 7-2-2. H. ASS’Y-DRAWER (G-DRAWER:4B8C,5B5C) a. ASS’Y BILL-COIN (4B8C) No. Code No.
7 Exploded View and Parts List 7-2 DRAWER 7-2-2. H. ASS’Y-DRAWER (G-DRAWER:4B8C,5B5C) d. ASS’Y BOTTOM No. Code No.
7 Exploded View and Parts List 7-2 DRAWER 7-2-2. H. ASS’Y-DRAWER (G-DRAWER:5B8C) A.ASS’Y BILLCOIN (5B8C) B.ASS’Y HOUSING C.ASS’Y LOCK E.ASS’Y TRAY D.
7 Exploded View and Parts List 7-2 DRAWER 7-2-2. H. ASS’Y-DRAWER (G-DRAWER:5B8C) Figure 7-19 Lubrication Points of the G-Drawer(5B8C) No. Code No.
7 Exploded View and Parts List 7-2 DRAWER 7-2-2. H. ASS’Y-DRAWER (G-DRAWER:5B8C) a. ASS’Y BILL-COIN (5B8C) No. Code No.
7 Exploded View and Parts List 7-2 DRAWER 7-2-2. H. ASS’Y-DRAWER (G-DRAWER: 5B8C) d. ASS’Y BOTTOM No. Code No.
7 Exploded View and Parts List MEMO 7-34 SAM4S ER-900/SPS-300 SERIES
8 PCB Layout and Parts List 8-1 Main PCB SAM4S ER-900/SPS-300 SERIES 8-1
8 PCB Layout and Parts List 8-1 Main PCB No Part-No - JK92-01700D Description / Specification PBA MAIN:SPS-340,22A,16Mb,STD Q'TY Design-location Serviceable 1 ASSY Y N - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,100(S 1 ROM VER. 제조년월 - 0402-000290 DIODE-BRIDGE:GBU6B,GBU6J,100V 1 BD1 Y - 0502-000234 TR-POWER:KSA1010Y,PNP,40W,TO-220,100-200 1 Q32 Y - 2401-001313 C-AL:4700uF,20%,50V,LUG,φ25.
8 PCB Layout and Parts List 8-1 Main PCB No Part-No Description / Specification - 0505-000148 POWER MOSFET:FDS4141,SOIC,8P 1 U15 Y - 0602-000001 LED;SSC-UR101,RED,1608,SMD 3 LED1,LED2,LED3 Y - 0801-001063 IC-CMOS LOGIC:74HCT05,INVERTER,SOIC,14P 1 U17 Y - 0801-001100 IC-CMOS;74ACT245,TRANSECIVER,TSOP,20P 1 U13 Y - 0801-001105 IC-CMOS;SN74LVC138A,DECODER,TSOP,16P 4 U16,U21,U23,U24 Y - 0801-001110 IC-CMOS;74LV14A,INVERTER,TSOP,14P 1 U11 Y - 0801-001119 IC-CMOS LOGIC:7
8 PCB Layout and Parts List 8-1 Main PCB No Part-No Description / Specification Q'TY Design-location R2,R21,R44,R61,R118, R137,R144 R1,R23,R34,R41,R45, R56,R68,R73,R75,R80, R95,R96,R102,R104, R108,R138,R143-R157, R161,R177,R185, R189-R195,R202 Serviceable - 2008-000031 R-CHIP:2.2KOHM,5%,1/10W,1608 7 - 2008-000037 R-CHIP:4.7KOHM,1%,1/10W,1608,1% 32 - 2008-000041 R-CHIP:6.
8 PCB Layout and Parts List 8-1 Main PCB No Part-No - 2204-000029 Description / Specification C-CERAMIC,CHIP:1uF,+80-20%,16V,Y5V,1608 Q'TY Design-location Serviceable 3 C25,C68,C89 N Y - 2205-000002 C-TANTAL:10uF,16V,3528 6 CE4,CE5,CE7,CE8, CE9,CE10 - 2402-000168 C-AL,SMD:100uF,20%,16V,F60,Ø6.3×5.7L 3 CE1,CE14,CE15 Y - 2402-000179 C-AL,SMD:47uF,16V,φ6.3*5.
8 PCB Layout and Parts List 8-2 I/F PCB 8-6 SAM4S ER-900/SPS-300 SERIES
8 PCB Layout and Parts List 8-2 I/F PCB No Part-No Description / Specification Q'TY Design-location - JK92-01702E PBA SUB:SPS-300,INTERFACE B'D,SVC10 1 ASSY Y - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,100 1 제조년월 N - 3708-001419 CONNECTOR-FFC:24P,1mm,ST,DIP,TOP,IVORY 1 ICN3 Y - 3711-001495 CONN-HEADER:NOWALL,8P,2R,2.54mm,ST 2 ICN1,ICN4 Y - 3711-002006 CON-HEADER:BOX,16P,2R,2mm,AN,MALE 1 ICN7 Y - 3711-004105 WAFER;BOX-HEADER,1R,4P,2.
8 PCB Layout and Parts List 8-3 LCD PCB No Part-No - JK92-01702G PBA SUB:ER-900,LCD B'D,SVC 1 ASSY Y - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,100 1 제조년월 N - 3708-001421 CONNECTOR-FFC:17P,1mm,AN,DIP,UPSIDE,IVR 1 LCN3 Y - 3711-002002 CONNECTOR-HEADER:BOX,22P,2R,2mm,ST,BLK 1 LCN2 Y - 3711-003340 WAFER-BOX:16P,2R,2mm,ST,BLACK,YDW200-16 1 LCN4 Y - 3712-000011 CONNECTOR-BOX;22P,2R,2mm,AN,BLACK,YH 1 LCN5 Y - 3712-000012 CONNECTOR-BOX;18P,2R,2mm,AN,BLACK,YH 1 LCN1
8 PCB Layout and Parts List 8-4 REAR DISPLAY(FND) PCB No Part-No Description / Specification - JK92-01702H PBA SUB:ER-900,REAR DISPLAY,SVC 1 ASSY Y - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,100 1 제조년월 N - 3708-001421 CONNECTOR-FFC:17P,1mm,AN,DIP,UPSIDE,IVR 1 DCN1 Y - JK07-00018A DISPLAY-FND:ER180,FND*4,12PIN,Y/G 2 DU2,DU3 Y - JK07-00019A DISPLAY-FND:NEWNET,FND*1,10PIN,Y/G,ANODE 1 DU1 Y - 2008-000012 R-CHIP:200 OHM,5%,1/10W,1608 16 DR1-DR16 N - JK41-10816A PC
8 PCB Layout and Parts List 8-5 PRT JOINT PCB No Part-No Description / Specification Q'TY Design-location Serviceable - JK92-01702J PBA SUB:ER-900,JOINT B'D,SVC 1 ASSY Y - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,100(S 1 제조년월 N - 3708-001397 CONNECTOR-FPC/FFC/PIC:30P,1mmAN,DIP,SIDE 1 JCN6 Y Y - 3710-000111 CONNECTOR-SHUNT:2P,1R,2.54mm,JMHHA01 2 JCN3 (1 PRT) JCN4 (1 PRT) - 3711-001475 CONN-HEADER:NOWALL,3P,1R,2.
8 PCB Layout and Parts List 8-6 OPTION I/F(232*2) PCB No Part-No Description / Specification Q'TY Design-location Serviceable - JK92-01703A PBA SUB:NEWNET,OPTION I/F,232*2 1 ASS’Y Y - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,100(S 1 제조년월 N - JK70-20173A IPR-BRKT OPTION:ER-900,SECC T1.
8 PCB Layout and Parts List 8-7 OPTION I/F(232&USB) PCB 8-12 SAM4S ER-900/SPS-300 SERIES
8 PCB Layout and Parts List 8-7 OPTION I/F(232&USB) PCB No Part-No Description / Specification Q'TY Design-location Serviceable - JK92-01706A PBA SUB:NEWNET,OPTION I/F,232&USB 1 ASS’Y Y - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,10 1 제조년월 N - JK70-20173B IPR-BRKT OPTION:ER-900,SECC T1.
8 PCB Layout and Parts List 8-8 SDCARD PCB No Part-No Description / Specification Q'TY Design-location Serviceable - JK92-01704A PBA SUB:NEWNET,SD CARD 1 ASS’Y Y - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,100 1 제조년월 N - JK39-40756C HAR-SDCARD:NEWNET,10P,300mm,AT TAPE 1 Y - JK70-20122A IPR-BRKT SD;NEX1,SECC T1.
8 PCB Layout and Parts List 8-9 LAN PCB No Part-No Description / Specification Q'TY Design-location Serviceable - JK92-01705A PBA SUB:NEWNET,LAN 1 - 6001-000665 SCREW-MACHINE:PWH,+,M3,L4,ZPC(YEL),SM20 1 I/F B'D+IRC B'D Y - JC68-10564A LABEL(P)-PROTECTOR:SLB-3108H,ART,-,100 1 제조년월 N - 3301-000344 CORE-FERRITE BEAD:DOUBLE,35*65,RADIAL 1 L1 Y - 3712-000085 CON-BOX:8P,2.
8 PCB Layout and Parts List MEMO 8-16 SAM4S ER-900/SPS-300 SERIES
9 Wiring Diagram 9-1 Main PBA Block Diagram SAM4S ER-900/SPS-300 SERIES 9-1
9 Wiring Diagram 9-2 Main PBA Wiring connection CN1 (JTAG) NO CN2 ( MAIN B’D to PRT_R JOINT B’D CONNECTOR ) SIGNAL NAME NO SIGNAL NAME 1 GND 1 2 GND 2 SPOOL_MOT_IN 3 /RESET 3 VPH 4 JTAG_TDO 4 TPH_DATA 5 JTAG_RTCK 5 6 JTAG_TCK 6 7 JTAG_TMS 7 8 JTAG_TDI 9 10 NO SIGNAL NAME 1 GND 17 VPH 2 SDC_/CD 18 SEN_PEND(R)_IN 3 SDC_/WP 19 SEN_PEND(R)_LED 4 SDC_DATA1 TPH_CLK 20 SEN_COVER(R)_IN 5 SDC_DATA0 GND 21 MOTOUT(R)_/A 6 SDC_CLK SEN_PRTDISCON(R) 22 MOTOUT(R)
9 Wiring Diagram 9-2 Main PBA Wiring connection CN12 ( FISCAL CONNECTOR ) NO 1 SIGNAL NAME CN13 ( MAIN B’D to INTERFACE B’D CONNECTOR ) NO SIGNAL NAME NO SIGNAL NAME FA(8) 1 2 FISEPROM_PGM 19 FISCAL EPROM VCC 2 USB_D- 14 COM#2_TXD 3 GND 20 FA(13) 3 COM#4_RXD 15 COM#1_CTS 4 FISEPROM_OE 21 GND 4 COM#4_TXD 16 COM#1_RXD 5 FD(2) 22 FA(14) 5 COM#4_RTS&USB_SELT 17 COM#1_RTS 6 FD(1) 23 FISEPROM_CE 6 COM#4_CTS&SEN_VUSBOCP 18 COM#1_TXD 7 FD(7) 24 FA(15) 7 COM#3_RX
9 Wiring Diagram 9-3 I/F PBA Block Diagram 9-4 I/F PBA Wiring connection CN2 (DRAWER#2, RJ-11 MODULAR TYPE) CN1 (I/F B’D to LAN SUB B’D NOWALL 8P TYPE) NO SIGNAL NAME NO SIGNAL NAME NO SIGNAL NAME 1 LANLED_LINK&ACT 5 GND 1 GND 2 VDD18V 6 GND 2 DRAWER#2_IN 3 VDD33V 7 LAN_TX- 3 SENSOR_DWRCOMP#2_IN 4 VDD33V 8 LAN_TX+ 4 +24V 5 N.
9 Wiring Diagram 9-4 I/F PBA Wiring connection CN5 (SERIAL#1,#2 DSUB9PIN TYPE) NO SIGNAL NAME CN6 (I/F POWER +DRAWER CONNECTOR) NO SIGNAL NAME NO 1 NC 10 NC 1 2 COM#1_RXD_IN 11 COM#2_RXD_IN 3 COM#1_TXD_OUT 12 COM#2_TXD_OUT 4 COM#1_RTS_OUT 13 5 GND 6 COM#1_CTS_IN SIGNAL NAME +24V 2 SEN_DWRCOMP#1 9 +24V 3 DRAWER#2 10 SEN_VSERIALOCP COM#2_RTS_OUT 4 SEN_DWRCOMP#2 11 VSERIAL_ONOFF 14 GND 5 VDD18V 12 VUSB50V 15 COM#2_CTS_IN 6 VDD33V 13 GND 7 VDD50V 14 GND CO
9 Wiring Diagram 9-5 LCD JOINT PBA Block Diagram 9-6 LCD JOINT PBA Wiring connection CN1 REAR DISPLAY( MAIN B’D to LCD JOINT B’D CONNECTOR ) NO SIGNAL NAME 1 GND 2 VFD_GRD#9 3 VFD_SEG#2(B) 4 VFD_GRD#1 5 VFD_SEG#1(A) 6 VFD_GRD#2 7 VFD_SEG#6(F) 8 VFD_GRD#3 9 VFD_SEG#7(G) NO 10 SIGNAL NAME SIGNAL NAME NO SIGNAL NAME VFD_GRD#5 1 GND 11 VFD_SEG#3(C) 2 12 VFD_GRD#6 3 13 VFD_SEG#8(DP) 14 NO SIGNAL NAME 12 D(5) VDD50V 13 D(6) VCONTRAST 14 D(7) 4 DATA/INST 15 CE1
9 Wiring Diagram 9-7 REAR DISPLAY(FND) PBA Block Diagram 9-8 REAR DISPLAY(FND) PBA Wiring connection CN1 REAR DISPLAY(LCD JOINT B’D to REAR DISPLAY CONNECTOR ) NO SIGNAL NAME NO SIGNAL NAME 1 VFD_SEG#5(E)_IN 10 VFD_GRD#5_OUT 2 VFD_GRD#4_OUT 11 VFD_SEG#6(F)_IN 3 VFD_SEG#4(D)_IN 12 VFD_GRD#3_OUT 4 VFD_GRD#8_OUT 13 VFD_SEG#1(A)_IN 5 VFD_SEG#8(DP)_IN 14 VFD_GRD#2_OUT 6 VFD_GRD#7_OUT 15 VFD_SEG#2(B)_IN 7 VFD_SEG#3(C)_IN 16 VFD_GRD#1_OUT 8 VFD_GRD#6_OUT 17 VFD_GRD#9_OUT 9 VF
9 Wiring Diagram 9-9 PRT JOINT(R/J) PBA Block Diagram 9-10 PRT JOINT(R/J) PBA Wiring connection CN1 (PRINTER CONNECTOR ) NO 9-8 SIGNAL NAME CN2 (AUTOCUT CONNECTOR) NO SIGNAL NAME NO 1 VPH 26 GND 1 2 VPH 27 GND 3 VPH 28 GND 4 VPH 29 5 VPH 6 VPH 7 TPH_DATA 8 9 SIGNAL NAME NO SIGNAL NAME N.
9 Wiring Diagram 9-11 OPTION SERIAL 2P(RJ45+RJ45) PBA Block Diagram 9-12 PRT JOINT(R/J) PBA Wiring connection CN2 (I/F B’D to OPTION B’D CONNECTOR) CN1 (SERIAL#3,#4 RJ-45 MODULAR TYPE) NO 1 SIGNAL NAME COM#3_RTS_OUT NO 9 SIGNAL NAME NO SIGNAL NAME COM#4_RTS_OUT 1 COM#4_CTS NO SIGNAL NAME 9 COM#3_CTS GND 2 GND 10 GND 2 N.C 10 3 COM#3_CTS_IN 11 COM#4_CTS_IN 3 COM#4_RTS 11 COM#3_RTS 4 COM#3_RTS_OUT 12 COM#4_RTS_OUT 4 N.C 12 N.
9 Wiring Diagram 9-13 SDCARD PBA Block Diagram 9-14 SDCARD PBA Wiring connection SCN1 (SD B’D CONNECTOR 10P) NO 9-10 SIGNAL NAME SCN2 (SD CARD 10P) NO SIGNAL NAME 1 GND 1 SDC_DATA3(SD) 2 SDC_/CD 2 SDC_CMD(SD) 3 SDC_WP 3 GND(SD) 4 SDC_DATA1 4 VDD_3.3V(SD) 5 SDC_DATA0 5 SDC_CLK(SD) 6 SDC_CLK 6 GND(SD) 7 VDD(3.3V) 7 VDD(3.
9 Wiring Diagram 9-15 LAN PBA Block Diagram 9-16 LAN PBA Wiring connection CN1 (ETHERNET RJ-45 MODULAR TYPE) NO SIGNAL NAME CN2 (I/F B’D to LAN SUB B’D NOWALL 8P TYPE) NO SIGNAL NAME NO SIGNAL NAME NO SIGNAL NAME 1 LAN_TX+ 7 LAN_RX+ 1 LANLED_LINK&ACT 5 GND 2 LAN_TX- 8 LAN_RX- 2 N.C 6 GND 3 LAN_TX CT 9 VDD33V(LED) 3 N.C 7 LAN_TX- 4 N.C 10 LANLED_SPEED 4 N.C 8 LAN_TX+ 5 N.
9 Wiring Diagram 9-17 OPTION SERIAL 1P(RJ45) PBA Block Diagram 9-18 OPTION SERIAL 1P(RJ45) PBA Wiring connection CN1 (SERIAL#3 RJ-45 MODULAR TYPE) CN2 (I/F B’D to OPTION B’D CONNECTOR) NO NO SIGNAL NAME SIGNAL NAME CN3 (SERIAL 1P B’D to USB B’D CONNECTOR) NO 1 VSERIAL50V(COM3&4) 1 COM#4_CTS&SEN_VUSBOCP 2 COM#3_CTS_IN 2 USB_D+ 3 COM#3_TXD_OUT 3 COM#4_RTS&USB_SELT 4 COM#3_RXD_IN 4 USB_D- 12 5 COM#3_RTS_OUT 5 N.C 6 COM#3_CTS_IN 6 VDD50V 7 GND 7 N.
JOURNAL (2-STATION) or RECEIP (1-STATION) THERMAL PRINTER JOINT B'D AUTOCUT 1-STATION or 2-STATION PRINTER (CAPD245 or LTPD 245) IN OUT 19V/2.
10 Block Diagram MEMO 10-2 SAM4S ER-900/SPS-300 SERIES
11 Schematic Diagrams [ Schematics Sheet Contents ] 1. Main PCB Schematics. 1) CPU(LPC2470) & Reset & Extout Block -------------------2) Memory & Buzz & Pfail & Batt Block ------------------------3) KBD & Dallas & Sensor & MSR Block ----------------------4) LCD(192x64 & 2line LCD) Block -----------------------------5) Printer(1st & 2st & Autocut) & Spool Block -----------------6) FND conn. & I/F conn. & Drawer conn.
4 3 2 R28 10K C17 22pF X3 12MHZ A C24 22pF SYSTEM XTAL ENET_MDINTR /WBLS1 /WBLS0 R33 0 R60 N.C XOUT XIN /RSTOUT 35 29 34 36 37 44 46 183 179 87 95 119 139 170 176 187 193 91 99 75 79 83 97 103 107 113 121 127 131 135 145 149 155 159 173 101 104 105 111 109 115 123 129 C27 100nF R30 10K VDD33V XCOUT /RESET XCIN XIN XOUT /WE /OE ENET_LINKSTS R32 0 BOOT CONTROL PIN SELECT P3.15 P3.
SAM4S ER-900/SPS-300 SERIES 11-3 4 3 2 1 R8 470 1 BAT1 ML2032,COIN,3V,65mAH ★ ★ NOPOP★★ DEBUG A NOPOP R4 10K R7 10K JTAG_DBGEN VDD33V A(0:21) D(0:15) JTAG_TDO /RESET JTAG_RTCK JTAG_TMS JTAG_TCK JTAG_TDI JTAG_/TRST 10 9 8 7 6 5 4 3 2 1 26 28 11 10 13 9 16 17 48 1 2 3 4 5 6 7 8 18 19 20 21 22 23 24 25 CE OE WE NC1 NC2 VSS1 VSS2 RESET RY/BY BYTE WP 46 27 12 15 47 14 45 C74 100nF D(15) A19 A0/DQ15 43 D(14) A18 DQ14 41 D(13) A17 DQ13 39 D(12) A16 DQ12 36 D(11) A15 DQ11 34 D(10)
4 3 2 1 C95 100nF VDD33V C91 100nF VDD33V C90 100nF RTC A C1 15pF 1 2 3 4 6 74HC05 74HC05 8 5 8 7 6 5 U1 VBT33V PCF8563TS OSCI VDD OSCO CLKO INT SCL VSS SDA A(2) A(1) A(0) 3 A(4) /CS2_KEYSCAN 74HC05 1 R15 1K VDD33V 6 5 4 3 2 1 16 E3 E2 E1 A1 A2 A0 VCC 6 5 4 3 2 1 16 E3 E2 E1 A2 A1 A0 VCC I2C_SDA GND Q7 Q6 Q5 Q3 Q4 Q2 Q1 Q0 GND Q7 Q6 Q4 Q5 Q3 Q2 Q1 Q0 Q7 GND Q6 Q5 Q4 Q3 ZD1 BZT52C6V2 6.2V DALLAS_SIGNAL R144 2.
4 3 2 R110 470 1 2 3 Q16 MMBT2222A LCD_RGB(KR)_IN MAX 240m A R112 470 1 2 3 Q17 MMBT2222A 2 3 R114 470 1 A CON-BOX;22P,2MM,2R,ST LD(0:7) CN9:A 1 3 5 LCD_RW_OUT 7 LD(0) 9 LD(2) 11 LD(4) 13 LD(6) 15 17 VLCD 19 21 2 4 6 8 10 12 14 16 18 20 22 LCD_RGB(KG)_IN BackLit GND LD(5) LD(7) LD(1) LD(3) KG A LCD_RGB(KB)_IN 2LINE LCD PIN CONNECTION SIG NAME NO SIG NAME 1 2 VDD VSS 3 4 DATA/INST LCD DRIVE R/W 5 6 EN D0 7 8 D1 D2 9 10 D3 D4 11 12 D5 13 14 D7 D6 N.C 15 16 N.C N.C 17 18 N.C N.
4 3 2 1 R38 470 R37 1K 2 3 R23 4.7K A ACMOT_EN R25 560 R3 C3 100nF R1 4.7K R1 R2 2.
SAM4S ER-900/SPS-300 SERIES 11-7 4 3 2 1 A A 1DIG d g a c b dp ... e f VFD_GRD#8 VFD_GRD#4 VFD_GRD#6 VFD_GRD#7 VFD_GRD#3 VFD_GRD#5 VFD_GRD#2 VFD_GRD#9 VFD_GRD#1 CON-BOX;18P,2MM,2R,ST CN16:A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 a g 8DIG d b c VFD_SEG#4(D) VFD_SEG#5(E) VFD_SEG#3(C) VFD_SEG#8(DP) VFD_SEG#6(F) VFD_SEG#7(G) VFD_SEG#1(A) VFD_SEG#2(B) DISPLAY INTERFACE CONN.
4 3 2 1 0 A SDC_/CD SDC_/WP SPI_CLK SPI_DO(DATA) SPI_DI(CMD) SPI_CS SDCARD CONN. ENET_RXD1 ENET_RXD0 ENET_RXD3 ENET_RXD2 ENET_RX_ER ENET_RX_CLK R51 VDD33V AGND C47 22pF R43 10K R42 10K R95 4.7K C48 100nF 0 C42 22pF 22 22 R48 10K ENET_TXD0 ENET_TXD2 ENET_TXD1 ENET_TXD3 10 9 8 7 6 5 4 3 2 1 VSDCARD AGND X4 25MHZ R49 10K ENET_TX_CLK ENET_TX_ER R45 4.
4 3 2 1 /CS2_FISDATA_WR FISCAL_DATA_WR /CS2_FISADDH_WR INVT_/WE /CS2_FISADDL_WR 74LVC32 U33:C 7 11 A /OE /CS2_FISDATA_RD 12 74LVC32 U33:D R188 4.
4 3 2 1 8 7 6 5 DC SC SENSE SE VCC TC IN GND U34 KA34063A A +24V SK14 D20 VDD5.0V POWER +24V VPRT(+9V) POWER CN17:A CN17:B CE13 470uF 50V 1 2 3 4 1 2 CON-WALL;2P,3.96MM,1R,1W,ST CN18:2 CN18:1 2 1 FU1 250V/3.15A C102 100nF 2012 R200 10K R203 10K HS1 3 2 T2,W17,L22,H30 1 5 1 SD 3 6 FB VOUT GND VIN U26 AP1501-50K5 Q33 KSA1182-Y Q32 KSA1010Y 노노 ] "LOW" ACTIVE C103 100nF 2012 C108 100pF R202 4.7K R199 470 4 BD1 BD_KBU6B CON-BOX;2P,2.
4 3 2 1 COM#3_RXD COM#3_TXD COM#3_RTS COM#3_CTS COM#2_CTS COM#2_RXD COM#2_RTS COM#2_TXD COM#1_CTS COM#1_RXD COM#1_RTS COM#1_TXD LAN_RX+ LAN_RX- LANLED_LINK&ACT COM#1_RXD_IN COM#2_CTS_IN COM#2_RTS_OUT COM#2_TXD_OUT COM#2_RXD_IN COM#1_CTS_IN COM#1_RTS_OUT COM#1_TXD_OUT DRAWER#1 SEN_DWRCOMP#2 DRAWER#2 SEN_DWRCOMP#1 CN3:A CN3:B CN3:C CN3:D CN3:E CN3:F CN3:G CN3:H CN3:I CN3:J CN3:K CN3:L CN3:M CN3:N CN3:O CN3:P CN3:Q CN3:R CN3:S CN3:T CN3:U CN3:V CN3:W CN3:X 1 2 3 4 5 6 7 8 9 1 2
11-12 SAM4S ER-900/SPS-300 SERIES 4 3 2 1 R10 1K 1 3 SEN_DWRCOMP#1 2 3 Q3 MMBT2222A Q4 SL1002 COM#4_RTS&USB_SELT COM#4_TXD COM#4_RXD COM#3_CTS COM#3_RTS COM#3_RXD FGND COM#4_CTS&VUSB_OCP A 1 2 R11 100 5 7 9 11 13 15 CN7:F CN7:N CN7:O CN7:P CN7:L CN7:K CN7:M CN7:I CN7:J CN7:G CN7:H CN7:E 6 8 10 12 14 16 FGND USB_D+ USB_D- VDD50V L3 2012 2012 L1 2012 L2 D2 M4 +24V CON-BOX;16P,2MM,2R,AN,MALE VDD33V 1 CN7:A CN7:B 2 VSERIAL50V(COM3&4) 3 CN7:C CN7:D 4 VUSB50V COM#3_TX
SAM4S ER-900/SPS-300 SERIES 11-13 4 3 2 1 A A 2 4 6 8 10 12 14 16 BackLit GND LCD_RGB(KB)&VLCD 2 4 6 8 10 12 14 16 18 20 22 LCD_RGB(KG)_OUT LCD_RGB(KR)_OUT /RESET_IN LCD_CE2_CENTER_IN LD(7) LD(5) LD(3) LD(1) /CS2_LCD_IN LCD_D/I_IN VDD50V 노노 ] 192*64 LCD 전용 커커커 CON-BOX;22P,2MM,2R,ST CN2:A 1 3 5 LCD_RW_IN 7 LD(0) 9 LD(2) 11 LD(4) 13 LD(6) 15 LCD_CE1_LEFT_IN 17 LCD_CE3_RIGHT_IN 19 VOUT 21 VCONTRAST LD(7) LD(5) LD(3) LD(1) /CS2_LCD_IN LCD_D/I_IN VDD50V 192x64 FRONT LCD CONN.
4 3 2 1 R35 R36 R40 R41 1K 470 1K 470 1K 470 1K 470 R5 R10 R45 R46 R43 R44 R50 R49 VFD_GRD#9 VFD_GRD#6 VFD_GRD#7 VFD_GRD#8 VFD_GRD#4 1K 470 1K 470 1K 470 1K R2 R7 R3 R8 R4 R9 R51 A 3 2 3 1 3 3 2 3 1 3 Q11 MMBT2222A 1 2 Q9 MMBT2222A 1 3 2 Q5 MMBT2222A 1 2 Q1 MMBT2222A 1 2 Q24 MMBT2222A 3 Q21 MMBT2222A 1 2 Q17 MMBT2222A 1 3 2 Q14 MMBT2222A 1 4.7K 4.7K 4.7K 4.
4 3 2 1 d g a c b dp CN1:B CN1:D CN1:F CN1:H CN1:J CN1:L CN1:N CN1:P CN1:Q A 2 4 6 8 10 12 14 16 17 A B C D E F G DP COMMON-ANODE TYPE DIG e f A U3 U1 B VFD_GRD#9 VFD_GRD#1 VFD_GRD#2 VFD_GRD#3 VFD_GRD#5 VFD_GRD#6 VFD_GRD#7 VFD_GRD#8 VFD_GRD#4 CN1:O CN1:M CN1:K CN1:I CN1:G CN1:E CN1:C CN1:A 15 13 11 9 7 5 3 1 R13 R5 R14 R6 R7 R15 R16 R8 R9 R1 R11 R3 R10 R2 R12 R4 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 VFD_SEG#2(B) VFD_SEG#1(A) VFD_SEG#
11-16 SAM4S ER-900/SPS-300 SERIES 4 3 2 1 ① ① TOP CONTACT MAIN B'D PRINTER CONN PRT FPC CABLE TOP CONTACT A MAIN I/F B'D NO SIGNAL 1 VPRT 3 VPH 5 TPH_CLK(R) 7 TPH_STB#456(R) 9 THERMISTER(R)_IN 11 GND 13 VPH 15 VPH 17 SEN_PEND(R)_LED 19 SEN_COVER(R)_IN 21 MOTOUT(R)_A 23 MOTOUT(R)_A 25 ACSW_SEN_LED 27 ACMOTOUT_B 29 ACMOTOUT_B ① ACMOTOUT_A ACMOTOUT_A ① ① 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 ① ① MAIN B'D ① CN6:ACCN6:AD CN6:AACN6:AB CN6:Y CN6:Z CN6:WCN6:X CN6:UCN6:V CN6:S CN6:T C
SAM4S ER-900/SPS-300 SERIES 11-17 4 3 2 1 A A C14 R2 100nF 10K COM#4_CTS COM#4_RXD COM#4_RTS C18 C9 100nF VDD33V COM#4_TXD COM#3_CTS COM#3_RXD 100nF VDD33V C5 C8 COM#3_RTS VDD33V C16 100nF VDD33V COM#3_TXD 100nF R1 10K 100nF VDD33V VDD33V 15 11 10 12 9 6 2 16 15 11 10 12 9 6 2 16 C2+ C2- C1+ C1- C2+ C2- C1+ C1- GND T1IN T1OUT T2IN T2OUT R1OUT R1IN R2OUT R2IN V- V+ VCC U2 MAX3232 GND T1IN T1OUT T2IN T2OUT R1OUT R1IN R2OUT R2IN V- V+ VCC U1 MAX3232 COM
4 3 2 A NO 1 2 3 4 5 6 7 8 9 10 SIGNAL GND SDC nCD SDC nWP SDC DATA1 SDC DATA0 SDC CLK VDD33V SDC CMD SDC DATA3 SDC DATA2 SPS-300 SD CARD B'd ① ⑩ B ① B ⑩ 1 A NO 1 2 3 4 5 6 7 8 9 10 SIGNAL GND(SD) SDC nCD(SD) SDC nWP(SD) SDC DATA1(SD) SDC DATA0(SD) SDC CLK(SD) VDD33V(SD) SDC CMD(SD) SDC DATA3(SD) SDC DATA2(SD) VDD33V(SD) GND(SD) SDC_CLK(SD) SC1 22pF GND(SD) CN12 CON-BOX;10P,1.
4 3 2 A LAN DM9161B MAIN B'D LAN CONN. LAN_RX+ 1 3 5 7 1 3 5 7 CN3:7 CN3:8 CN3:5 CN3:6 CN3:3 CN3:4 CN3:1 CN3:2 CN2:7 CN2:8 CN2:5 CN2:6 CN2:3 CN2:4 CN2:1 CN2:2 2 4 6 8 VDD33V 2 4 6 8 VDD33V B LANLED_SPEED L1 7 6 8 FGND 13 14 4 5 15 16 11 12 9 10 VDD33V LANLED_LINK&ACT LAN_RX- LAN_RX+ LAN_TX- LAN_TX+ TX(+) TX CT TX(-) N.C N.
4 3 2 1 A A 15 11 10 12 9 6 2 1 2 3 4 5 6 7 8 C2+ C2- C1+ C1- CN1:A CN1:B CN1:C CN1:D CN1:E CN1:F CN1:G CN1:H GND 14 7 13 8 4 5 1 3 DSR3 TXD3 RXD3 RTS3 CTS3 SGND DTR3 T1IN T1OUT T2IN T2OUT R1OUT R1IN R2OUT R2IN V- V+ VCC U1 MAX3232 FGND C12 100nF VDD50V COM#4_RTS&USB_SELT 3 1 R6 10K VDD33V 7 14 2 5 FGND U3:A 74HCT05 VDD50V 4 U3:B 74HCT05 R9 1K VDD50V L2 2012 2012 L1 9 8 U3:D 74HCT05 6 COM#3 USB_A C3 470pF C5 100nF C8 100nF R10 15K R8 15K 11 COM#1 COM
4 3 2 1 A A CN5:7 CN5:8 CN5:5 CN5:6 CN5:3 CN5:4 CN5:1 CN5:2 2 4 6 8 USB_D+ USB_D- 1 2 3 4 5 6 VUSB50V CN4:F CN4:E CN4:D CN4:C CN4:B CN4:A (1) Vbus (2) D(3) D+ (4)GND (5)F GND (6)F GND USB A B (1) Vbus (2) D(3) D+ (4)GND (5)F GND (6)F GND CON-USB;ATYPE,4P,1R,AN USB SUB B'D to I/F B'D CONN. USB_D- USB_D+ 1 3 5 7 VUSB50V CON-NOWALL;8P,2.54MM,2R,ST USB SUB B'D to I/F B'D CONN.
MEMO 11-22 SAM4S ER-900/SPS-300 SERIES
UPDATE LOG Application Date Page Part # Notes (Cause & Solution) S/Bulletin Use this page to record any special servicing information such as Service Bulletins or Supplements. When possible, record changes to Code numbers directly on the actual Parts List. Always record Service Bulletin numbers and Application Dates on this log to ensure that your data is always as current as possible.
ⓒ Shin Heung Precision. Oct. 2011 Printed in KOREA V1.0 Code No.
