Service manual

ManualsBrandsAuto Page ManualsCar alarmC3-RS-900LCD

CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716

CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/

TRV46/TRV46PK

SERVICE MANUAL

MICROFILM

SPECIFICATIONS

US Model

Canadian Model

CCD-TR416/TR516/TR716

CCD-TRV16/TRV36/TRV43/TRV46

E Model

CCD-TR315/TR416PK/TR516PK

CCD-TRV16/TRV16PK/TRV36PK/

TRV46/TRV46PK

Hong Kong Model

CCD-TRV16/TRV46

Taiwan Model

CCD-TRV16

Brazilian Model

CCD-TR315/TR416

CCD-TRV16

VIDEO CAMERA RECORDER

— Continued on next page —

Video camera recorder

System

Video recording system

2 Rotary heads

Helical scanning FM system

Audio recording system

Rotary heads, FM system

Video signal

NTSC color, EIA standards

Usable cassette

8mm video format cassette

CCD-TR315/TR416/TR416PK

CCD-TRV16/TRV16PK

: standard 8

CCD-TR516/TR516PK/TR716

CCD-TRV36/TRV36PK/TRV43/TRV46/

TRV46PK : Hi8

Recording / Playback time

(using 120 min. cassette)

SP mode: 2 hours

LP mode: 4 hours

Fastforward/rewind time

(using 120 min. cassette)

Approx. 5 min.

Image device

1/4 inch CCD (Charge Coupled Device)

CCD-TR315/TR416/TR416PK/TR516/

TR516PK

CCD-TRV16/TRV16PK/TRV36/

TRV36PK : Approx. 270,000 pixels

(Effective : approx 250,000 pixels)

CCD-TR716

CCD-TRV34/TRV46/TRV46PK :

Approx. 320,000 pixels

(Effective : approx 200,000 pixels)

Viewfinder

Electronic viewfinder

CCD-TR315/TRV series : Monochrome

CCD-TR416/TR416PK/TR516/

TR516PK/TR716 : Color

Lens

Combined power zoom lens

Filter diameter 1 7/16 in. (37 mm)

CCD-TR315/TR416:US,CND

CCD-TRV16/TRV16PK

: 18 x (Optical), 180 x (Digital)

CCD-TR416:BR/TR416PK

: 18 x (Optical), 220 x (Digital)

CCD-TR516/TR516PK/TR716

CCD-TRV36/TRV36PK/TRV43/TRV46/

TRV46PK

: 18 x (Optical), 330 x (Digital)

Focal distance

3/16 - 8 in. (4.1 - 37.8 mm)

When converted to a 35 mm still camera

CCD-TR315/TR416/TR416PK/TR516/

TR516PK

CCD-TRV16/TRV16PK/TRV36/

TRV36PK

: 1 9/16 - 28 in. (39.4 - 709 mm)

CCD-TR715

CCD-TRV43/TRV46/TRV46PK

: 1 7/8 - 33 1/2 in. (47.2 - 850 mm)

RMT-708

Photo : CCD-TR516

Photo : CCD-TRV46

VIDEO CAMERA RECORDER

CCD-TR315/TR416/TR416PK

CCD-TRV16/TRV16PK

CCD-TR516/TR516PK/TR716

CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK

Color temperature

Auto

Minimum illumination

0.4 lux at F 1.4

0 lux (in NightShot mode)*

Illumination range

0.4 lux to 100,000 lux

Recommended illumination

More than 100 lux

* Object invisible for the dark can be

shot with infrared lighting.

LCD screen (TRV series only)

Picture

2.5 inches measured diagonally

2 x 1 1/2 in.(50.3 x 37.4 mm)

On-screen display

TN LCD/TFT active matrix method

Total dot number

61,380 (279 x 220)

For MECHANISM ADJUSTMENTS, refer to

the “8mm Video MECHANICAL ADJUSTMENT

MANUAL VII” (9-973-801-11).

B MECHANISM

NTSC

Ver 1.0 1999.01

Summary of content (177 pages)

PAGE 1
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/ TRV46/TRV46PK RMT-708 SERVICE MANUAL US Model Canadian Model CCD-TR416/TR516/TR716 CCD-TRV16/TRV36/TRV43/TRV46 E Model Ver 1.0 1999.01 CCD-TR315/TR416PK/TR516PK CCD-TRV16/TRV16PK/TRV36PK/ TRV46/TRV46PK Photo : CCD-TR516 Hong Kong Model CCD-TRV16/TRV46 Taiwan Model CCD-TRV16 Brazilian Model CCD-TR315/TR416 CCD-TRV16 For MECHANISM ADJUSTMENTS, refer to the “8mm Video MECHANICAL ADJUSTMENT MANUAL VII” (9-973-801-11).
PAGE 2
Input and output connectors Video output Phono jack, 1 Vp-p, 75 ohms, unbalanced Audio output Monaural, Phone jack, 327 mV (at output impedance 47 kilohms) impedance less than 2.2 kilohms RFU DC OUT Special minijack, DC 5V Earphone jack (TRV series only) Monaural minijack (ø 3.5 mm) LANC control jack Stereo mini-minijack (ø 2.5 mm) MIC jack Mini jack, 0.388mV low impedance with 2.5 to 3.0 V DC, output impedance 6.8 kilohms (ø 3.
PAGE 3
Table for difference of function CCDTR416PK CCDTR516 CCDTR516PK CCDTR716 CCDTRV16 BR E US,CND E US,CND Color G G ¬ 180X G 510 G G G TYPE G Color G G ¬ 220X G 510 G G G Color G G ¬ 220X G 510 G G G Color ¬ ¬ G 330X ¬ 510 G G G US,CND,E, E HK,BR,TW TYPE F B/W B/W G G G G ¬ ¬ 180X 180X G G 510 510 G G G G 2.5 inch 2.
PAGE 4
Supplied accessories 1 2 3 4 5 7 8 9 1 RMT-708 Wireless Remote Commander (1) 6 7 Shoulder strap (1) CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK 8 Video P6-15P HB tape CCD-TR416: US/TR516: US/TR716:US CCD-TRV16:US/TRV36:US/TRV43:US/TRV46:US 2 AC-L10A/L10B/L10C AC power adaptor 3 NP-F330 Battery pack (1) 9 2 pin conversion adaptor (1) CCD- TR315//TR416PK/TR516PK CCD- TRV16:E,BR,HK,TW/TRV16PK/TRV36PK/ TRV46:E,HK/TRV46PK 4 CR2025 Lithium Battery (1) The lithium battery is alrea
PAGE 5
SERVICE NOTE 1. POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following three methods are available to prevent this. Take note of which to use during repairs. Battery switch Method 1. Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the remote commander switch to the “ADJ” side. Method 2.
PAGE 6
SELF-DIAGNOSIS FUNCTION 1. Self-diagnosis Function 2. Self-diagnosis display When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or Display window what to do. This function consists of two display; selfdiagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.
PAGE 7
4. Self-diagnosis Code Table Repaired by: Self-diagnosis Code Block Detailed Function Code C 2 C 2 C 2 1 0 2 0 3 0 C 3 1 1 C 3 1 1 C C C C C C C C C C C 3 3 3 3 3 3 3 3 3 3 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 3 3 4 4 4 4 4 C 3 2 1 C 3 2 1 C 3 2 2 C 3 2 2 C 3 2 2 C 3 2 2 C 3 2 3 C 3 2 3 C 3 2 4 C 3 2 4 C 3 2 4 C 3 2 4 C 3 2 4 E 6 1 0 E 6 1 1 E 6 2 0 E 6 2 0 Symptom/State Correction 0 Condensation. 0 Video head is dirty. 0 Non-standard battery is used.
PAGE 8
TABLE OF CONTENTS SERVICE NOTE 2. DISASSEMBLY 1. Power Supply During Repairs ................................................ 5 2. To Take out a Cassette when not Eject (Force Eject) .............. 5 2-1. Removal of Front Panel Block and Video Light Block .... 2-1 2-2. Removal of LB-54, VF-119 and VF-120 Boards (Color View Finder Models) .................. 2-2 2-3. Removal of VF-99 Board and CRT Assembly (B/W View Finder Models) ..................... 2-2 2-4. Removal of Cabinet (R) Block ................
PAGE 9
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 5. ADJUSTMENTS 4-1. Frame Schematic Diagram (1) ........................................... 4-1 • Frame Schematic Diagram (2) ........................................ 4-4 4-2. Printed Wiring Boards and Schematic Diagrams ............... 4-7 • CD-210/211 (CCD Imager) Board .................................. 4-8 • VC-215 (Camera, Y/C Processor, IN/OUT, REC/PB Head Amp, Servo/System Control, Servo, Audio, IR Transmitter, Mode Control) Board ...............
PAGE 10
5-2. MECHANICAL SECTION ADJUSTMENT ................. 5-34 2-1. Operating without a Cassette .......................................... 5-34 2-2. Tape path Adjustment ..................................................... 5-34 1. Preparations for adjustments ................................... 5-34 5-3. VIDEO SECTION ADJUSTMENTS ............................. 5-35 3-1. Preparations before Adjustment ...................................... 5-35 3-1-1. Equipments to be Used .......................................
PAGE 11
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 1 GENERAL 1-1 This section is extracted from instruction manual of CCD-TRV36/TRV43/TRV46.
PAGE 12
1-2
PAGE 13
1-3
PAGE 14
1-4
PAGE 15
1-5
PAGE 16
1-6
PAGE 17
1-7
PAGE 18
1-8
PAGE 19
1-9
PAGE 20
1-10
PAGE 21
1-11
PAGE 22
1-12
PAGE 23
1-13
PAGE 24
1-14
PAGE 25
1-15
PAGE 26
1-16
PAGE 27
1-17
PAGE 28
1-18
PAGE 29
1-19
PAGE 30
1-20E
PAGE 31
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 2 DISASSEMBLY The equipment can be removed using the following procedure. VIDEO CAMERA RECORDER 2-2. LB-54/VF-119 & 120 BOARDS (Color view finder models only) 2-3. CRT/VF-99 BOARD (B/W view finder models only) 2-1. FRONT PANEL BLOCK VIDEO LIGHT BLOCK (Video light models only) 2-5. CASSETTE LID ASSEMBLY 2-4. CABINET (R) BLOCK 2-13.
PAGE 32
2-2. REMOVAL OF LB-54, VF-119 AND VF-120 BOARDS (Color view finder model CCD-TR416/TR416PK/TR516/TR516PK/TR716) 1 Tilt-up the EVF block to the direction of arrow A. 5 FP-57 flexible board CN5401,20P 3 Remove the EVF rear cabinet assembly 4 Flexible retainer sheet to the direction of arrow B. !£ VF-119 board !º Back light cushion Four claws ( Turn the cushion (Sponge rubber) face to the LB-54 board side for installation.
PAGE 33
2-4. REMOVAL OF CABINET (R) BLOCK Note : Be sure to that the pin of the Lens assembly is put into the hole of the IR knob when attaching. (TR series) (TRV series) 5Flat cable (FFC-257F) 5Flat cable (FFC-257F) CN911, 45P CN911, 45P 2Two screws 2Two screws (M2 x 4) Pin 3Three screws (M2 x 4) Pin 3Three screws (M2 x 4) (M2 x 4) 6Harness (PD-108) 1Two screws 4Cabinet (R) block 1Two screws 4Cabinet (R) block (M2 x 4) (M2 x 4) IR knob IR knob 2-5. REMOVAL OF CASSETTE LID ASSEMBLY 2-6.
PAGE 34
2-7. REMOVAL OF CABINET (L) BLOCK 2-8. REMOVAL OF CONTROL SWITCH BLOCK Function Key Switch (FK-8500) 2Cabinet (L) block 1 Remove the Function key switch in Screwdriver(-) 2Flexible connector the direction of arrow with pushing the claw. Two claws CN935, 10P 3Flexible connector CN934,12P 1Screw (M2 x 3) Two claws 2-9. REMOVAL OF ZOOM LENS BLOCK AND VL-21/22 BOARD 2-10.
PAGE 35
2-11.
PAGE 36
2-13. REMOVAL OF TR COVER, CF-60 BOARD AND DISPLAY PANEL ...(TR series) !∞ Liquid crystal display panel Phase adjustment S024 !¢ LCD holder S015 4FP-57 flexible board...(Color EVF type only) CN007, 20P Flat cable (FFC-235)...
PAGE 37
2-15. SERVICE POSITION Preparation : Refer to previous section “DISASSEMBLY”, and connect as shown in the figure after each parts has been removed.
PAGE 38
2-16. CIRCUIT BOARDS LOCATION VF-119...Color EVF models only (Color EVF) LB-54...Color EVF models only (Back light) VF-120...Color EVF models only (Color EVF) CF-60...TR series only (Control) VL-21... TR516/TR516PK/TR716 VL-22... TRV36/TRV36PK/TRV43/ DD-117 (Power) TRV46/TRV46PK VF-99...B/W EVF models only (B/W EVF) (Video light) CD-210...TR series only CD-211...TRV series only (CCD imager) PJ-90...TR series PJ-91...TRV series (AV Out) VC-215 Camera, Y/C prosessor, IN/OUT, REC.
PAGE 39
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 3 BLOCK DIAGRAMS 3-1.
PAGE 40
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-2. CAMERA/VIDEO 1 BLOCK DIAGRAM CAMERA REC 0.3Vp-p 2V CAMERA REC IC001 H IC401 CAMERA REC 2V CAMERA REC 0.3Vp-p IC202 16 CAMERA REC 1.3Vp-p H CAMERA REC 5 TRIG : IC001 21 3Vp-p 0.4Vp-p 0.5Vp-p 1.3Vp-p 7 IC001 44 , 48 H IC001 H 3 IC202 13 H IC502 26 3.1 CAMERA REC PB 3.2Vp-p PB 0.4Vp-p 0.14usec 3.1 7Vp-p 0.4Vp-p IC502 2 — 10 V V IC202 40 IC001 17 H IC401 3 4 PB 0.
PAGE 41
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-3. VTR/CAMERA CONTROL BLOCK DIAGRAM 710 only 3.1V 3.1V 1.7Vp-p 20 MHz IC402 1 3.1V 3Vp-p 13usec 3.1V IC402 70 TR MODEL : CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 TRV MODEL : CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK COLOR EVF MODEL : CCD-TR416/TR416PK/TR516/TR516PK/TR716 STEADY SHOT MODEL : CCD-TRV43/TRV46/TRV46PK 3.1V 3Vp-p 4V IC402 48 3Vp-p 2V IC402 47 3.1V 3.1V 3.1V 3.
PAGE 42
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-4. SERVO BLOCK DIAGRAM 3Vp-p 13usec IC402 69 3Vp-p 0.76Vp-p 2.8msec 506 kHz IC402 116 IC801 64 3.1V 1.2Vp-p 5.6msec IC451 3.1V 1 , 2 , 29 3Vp-p 3Vp-p 2V 1.2msec 0.
PAGE 43
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-5. MODE CONTROL BLOCK DIAGRAM SELECT (TRV MODEL) 1.5Vp-p 20 MHz IC604 41 2.
PAGE 44
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-6. AUDIO BLOCK DIAGRAM 0.7Vp-p 0.5Vp-p H 0.09usec IC751 22 IC751 41 PB 0.4Vp-p 0.34Vp-p V 0.09usec IC301 24 IC751 16 3.1V 0.5Vp-p 2usec IC751 15 0.25Vp-p 3.58 MHz IC751 7 CAMERA REC 0.36Vp-p V IC301 29 CAMERA REC TR716 only 0.26Vp-p 3.58 MHz IC301 32 3.
PAGE 45
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-7. LCD BLOCK DIAGRAM (TRV MODEL) H IC5502 16 4.7Vp-p 2H IC5502 20 4.2Vp-p 0.7Vp-p 3.1V 3.1V H IC5502 13 2H IC5502 22 4.2Vp-p 2H IC5502 24 0.44Vp-p 4.2Vp-p 0.2Vp-p 15 IC5502 9 0.2Vp-p FRPV IC5502 8 H FRPT H 3.1V H IC5502 10 VGL COM 11 H 5601 4 IC5601 26 4.7Vp-p Approx.5.8MHz : 4.1Vp-p IC5602 DAC AMP 3 IN+ 1 FRPT OUT1 12 IC5601 24 FRPV 4.7Vp-p Approx.2.
PAGE 46
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-8. COLOR EVF BLOCK DIAGRAM (COLOR EVF MODEL) FP-57 (FLEXIBLE 7.5Vp-p 2H IC5401 22 7.2Vp-p 2H IC5401 20 3.1V LCD902 7.6Vp-p 2H 3.1V IC5401 24 3.1V 3.1V 3.1V 3Vp-p 3.1V H IC5401 14 3Vp-p 12Vp-p V H IC5404 45 IC5301 15 3Vp-p H IC5404 22 3.4Vp-p 1.84 MHz IC5404 23 , 24 3.1V 3Vp-p 7.852 kHz IC5404 20 , 21 3Vp-p 2.7Vp-p COLOR EVF MODEL : CCD-TR416/TR416PK/TR516/TR516PK/TR716 V 11.
PAGE 47
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 3-9. B/W EVF BLOCK DIAGRAM B/W EVF MODEL T901/T902 2.
PAGE 48
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK (VIDEO LIGHT MODEL) (TR MODEL TR516/TR516PK/TR716) 3-10. POWER BLOCK DIAGRAM (TRV MODEL TRV36/TRV36PK/TRV43/TRV46/TRV46PK) VIDEO 3.
PAGE 49
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1.
PAGE 50
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK FRAME SCHEMATIC DIAGRAM (2) FRAME 4-4 4-5 4-6
PAGE 51
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-210/211 (CCD IMAGER) PRINTED WIRING BOARD – Ref No. CD-210 BOARD: 4,000 series, CD-211 BOARD: 9,000 series – THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) CD-210/211 BOARD (SIDE B) CD-210/211 BOARD (SIDE A) • For printed wiring boards.
PAGE 52
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VC-215 (CAMERA, Y/C PROCESSOR, IN/OUT, REC/PB HEAD AMP, SERVO/SYSTEM CONTROL, SERVO, AUDIO, IR TRANSMITTER, MODE CONTROL) PRINTED WIRING BOARD VC-215 BOARD (SIDE B) C002 C003 C008 C011 C012 C013 C014 C015 C016 C017 C019 C020 C022 C025 C038 C040 C042 C043 C048 C050 C051 C054 C056 C058 C060 C066 C067 C068 C069 C070 C07
PAGE 53
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VC-215 BOARD (SIDE A) VC-215 BOARD (SIDE A) G 62 63 F 24 23 22 21 E 20 19 8 18 12 7 9 10 11 13 15 14 16 17 30 D 28 29 30 C 47 33 34 31 41 35 48 32 36 56 49 39 38 B 46 45 37 55 44 54 42 43 53 40 A 11 21 1-672-45609 10 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 11 12 13 14 15 16 4-13 17 18 C001 C004 C005 C006 C007 C010
PAGE 54
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (1/10) 1 CAMERA REC 2.3Vp-p NTSC : 28.636 MHz IC501 2 5 CAMERA REC 2.3Vp-p NTSC : 14.
PAGE 55
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board.
PAGE 56
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (3/10) 10 19 CAMERA REC CAMERA REC 3Vp-p 0.34Vp-p H H IC202 11 IC202 61 3 20 CAMERA REC CAMERA REC 3.1Vp-p 0.84Vp-p H 3.58 MHz IC202 12 IC202 66 6 21 CAMERA REC CAMERA REC 3Vp-p 0.5Vp-p 4V H IC202 71 IC202 13 13 22 CAMERA REC CAMERA REC 3Vp-p 0.
PAGE 57
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (4/10) CAMERA REC 28 0.46Vp-p H IC151 3 29 0.32Vp-p H IC151 5 30 H IC151 29 IC151 62 (2.1Vp-p) (1.
PAGE 58
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (5/10) 31 40 CAMERA REC CAMERA REC 0.3Vp-p H 4.12 MHz IC001 32 7Vp-p 3 Q001 C CAMERA REC 0.3Vp-p 2V IC001 33 5 TRIG : IC001 21 PB 0.4Vp-p H IC001 34 7 PB 0.4Vp-p V IC001 11 35 PB 0.4Vp-p V IC001 17 36 CAMERA REC 2.9Vp-p 2V IC001 21 37 CAMERA REC 3Vp-p 2V IC001 44 , 48 38 CAMERA REC 0.
PAGE 59
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (6/10) CAMERA REC 41 1.7Vp-p 20 MHz IC402 1 42 3Vp-p 2V IC402 47 43 3Vp-p 4V IC402 48 44 3Vp-p 13usec IC402 68 45 3Vp-p 13usec IC402 69 46 3Vp-p 13usec IC402 70 47 3Vp-p 1.2msec IC402 115 48 3Vp-p 2.
PAGE 60
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. 50 51 52 VC-215 BOARD (7/10) CAMERA REC 50 1.2Vp-p 5.6msec IC451 1 , 2 , 29 51 3Vp-p 2V IC451 11 52 3Vp-p 2.
PAGE 61
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (8/10) 53 CAMERA REC 2.9Vp-p 2V IC301 21 54 PB 0.4Vp-p V IC301 24 55 CAMERA REC 0.36Vp-p V IC301 29 56 CAMERA REC 0.26Vp-p 3.
PAGE 62
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VL-21/22 (VIDEO LIGHT (VIDEO LIGHT MODEL)) PRINTED WIRING BOARD • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. – Ref No. VL-21 BOARD: 1,000 series – VL-21/22 BOARD (SIDE B) VC-215 BOARD (9/10) PB VL-21/22 BOARD (SIDE A) 57 C 0.25Vp-p 3.58 MHz IC751 7 58 B 0.5Vp-p 2usec IC751 15 A K A A 59 K K 0.34Vp-p A CN151 0.
PAGE 63
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (10/10) 62 1.5Vp-p 20 MHz IC604 41 63 2.
PAGE 64
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SE-80/81 (STEADY SHOT (STEADY SHOT MODEL)) PRINTED WIRING BOARD – Ref No.
PAGE 65
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK PJ-90/91 (AV OUT) PRINTED WIRING BOARD – Ref No.
PAGE 66
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK MA-345, 346 (MIC, LASER LINK) PRINTED WIRING BOARD – Ref No.
PAGE 67
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 1.3 0.1 1.3 3.1 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 2.3 1.1 0.6 1.1 1.7 1.3 0.6 2.
PAGE 68
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CF-60 (CONTROL (TR Series)) PRINTED WIRING BOARD – Ref No.
PAGE 69
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK 1.4 1.4 1.4 1.4 CAMERA REC MODE 1.4 : 1.4 NO MARK 1.6 1.4 1.4 1.4 1.9 1.4 1.4 3 1.4 3 1.4 3 1.4 2.9 4-69 1.4 1.4 1.4 1.4 1.4 1.4 0.1 2.9 2.
PAGE 70
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CONTROL CF-61 (TRV Series) 4-72 4-73 4-74
PAGE 71
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CF-61 (CONTROL (TRV Series) PRINTED WIRING BOARD – Ref No.
PAGE 72
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK PD-107 (RGB DECODER, LCD DRIVE, BACK LIGHT, LCD (TRV Series)) PRINTED WIRING BOARD – Ref No.
PAGE 73
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK PD-107 BOARD (1/4) CAMERA REC 1 0.44Vp-p H IC5502 8 2 0.2Vp-p H IC5502 9 3 0.2Vp-p H IC5502 10 4 0.7Vp-p H IC5502 13 5 4.7Vp-p H IC5502 16 6 4.2Vp-p 2H IC5502 20 7 4.2Vp-p 2H IC5502 22 8 4.
PAGE 74
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–79 for Printed Wiring Board. PD-107 BOARD (2/4) CAMERA REC 9 4.7Vp-p H IC5601 4 10 4.7Vp-p 20msec IC5601 5 11 4.7Vp-p IC5601 24 12 4.1Vp-p IC5601 26 13 4.7Vp-p 20msec IC5601 34 14 4.
PAGE 75
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK • For schematic diagrams. • Refer to page 4–79 for Printed Wiring Board. • For schematic diagrams. • Refer to page 4–79 for Printed Wiring Board. 3KV PD-107 BOARD (4/4) CAMERA REC 15 2.9Vp-p 24.
PAGE 76
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VF-99 (B/W EVF) PRINTED WIRING BOARD – Ref No.
PAGE 77
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VF-119 (COLOR EVF (COLOR EVF MODEL)) PRINTED WIRING BOARD VF-119 BOARD CAMERA REC – Ref No. VF-119 BOARD: 10,000 series – VF-119 BOARD (SIDE B) VF-119 BOARD (SIDE A) 1 3Vp-p H IC5401 14 2 C 7.2Vp-p 2H IC5401 20 4 K 3 3 A 2 7.5Vp-p 2H 1 B 4 2 1 3 IC5401 22 7.6Vp-p 10 9 2H IC5401 24 7 A 5 8 5 6 3Vp-p 1-668-942V 13 1 09 2 3 IC5404 18 4 6 • For Printed Wiring Boards.
PAGE 78
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VF-120 BOARD CAMERA REC 1 2.
PAGE 79
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK VF-120 (COLOR EVF), LB-54 (BACK LIGHT) (COLOR EVF MODEL) PRINTED WIRING BOARDS – Ref No.
PAGE 80
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK DD-117 (POWER) PRINTED WIRING BOARD – Ref No. DD-117 BOARD: 2,000 series – DD-117 BOARD (SIDE B) DD-117 BOARD (SIDE A) DD-117 BOARD VF-119...Color EVF models only (Color EVF) LB-54...Color EVF models only (Back light) VF-120...Color EVF models only (Color EVF) CF-60...TR series only (Control) DD-117 (Power) VL-21... TR516/TR516PK/TR716 VL-22... TRV36/TRV36PK/TRV43/ TRV46/TRV46PK (Video light) PJ-90...
PAGE 81
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK DD-117 BOARD CAMERA REC 1 0.76Vp-p 507 kHz IC801 4 2 0.76Vp-p 506 kHz IC801 64 7.7 7.9 1.9 7.9 3.1 3.1 7.
PAGE 82
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 5 ADJUSTMENTS 5-1. Refer to page 3 as Table for distinction functions of models and classification CAMERA SECTION ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Adjusting driver • Regulated power supply Ref. No.
PAGE 83
1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-3, 4. 2) By setting the “Forced Camera Power ON mode”, the camera power can be turned ON even if the front panel block (MA-345/ 346 board, power switch, microphone unit) has been removed.
PAGE 84
TR MODEL Color monitor Vector scope Terminated at 75 Ω Lens block CD-210 board CN401 Regulaterd power supply (8.4 ± 0.
PAGE 85
TRV MODEL Color monitor Vector scope Terminated at 75 Ω Lens block CD-211 board CN401 Regulaterd power supply (8.4 ± 0.1 Vdc) Battery terminal (Note 2) Extension cable(16P) (J-6082-357-A) Adjusting remote commander VL-22 board CN151 Battery switch VIDEO terminal LANC jack CN935 CN909 CN551 CN501 CN934 CN911 CN902 VC-215 board CN910 CN801 CN915 CN916 CN901 CN001 CN931 CN905 CN906 CN908 MA-346 board CN303 DD-117 board CN933 Must be connected when performing the VIDEO system.
PAGE 86
1-1-3.Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. 1. POWER switch (MA-345/346 board) .................... CAMERA 2. NIGHT SHOT switch (Lens Block) ................................ OFF (Night shot model) 3. DEMO MODE (Menu display) ....................................... OFF 4. DIGITAL ZOOM (Menu display) ................................... OFF 5. STEADY SHOT (Menu display) ....................................
PAGE 87
1-1-4. Adjusting Remote Commander The adjusting remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjusting remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the nonvolatile memory. • Changing the address The address increases when the FF ()) button is pressed, and decreases when the REW (0) button is pressed.
PAGE 88
1-1-5. Data Processing The calculation of the DDS display and the adjusting remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Table 5-1-2. indicates the hexadecimal notation-the decimal notation calculation table.
PAGE 89
2. Modification of D, E, F Page Data If the D, E, F page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model.
PAGE 90
3. D Page Table Note1 : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Address Initial Remark Value 00 to 0F 10 00 Fixed data-1 11 00 12 00 13 Fixed data-2 14 (Modified data, copy the data 15 built in the same model.) 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 00 Fixed data-1 2B 00 2C 00 2D 00 2E Fixed data-2 2F 64 Fixed data-1 30 88 Battery end adj.
PAGE 91
4. F Page table Note 1: Fixed data-1 : Initialized data. ( Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Note 2 : There are three models classified by VTR formats as shown below, and the initial value of adjustment is different according to the model.
PAGE 92
Address 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD Initial Value 0A 00 Address Remark BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF Switching position adj.
PAGE 93
5. E Page Table Note 1: Fixed data-1 : Initialized data. ( Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Note 2: See “1-5. LCD SYSTEM ADJUSTMENT”.
PAGE 94
Address 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 Initial Value Address Remark D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC to FF Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 TR model:Fixed data-1/TRV model:Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-2 TR
PAGE 95
1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, Check that the specified value of “28MHz Origin Oscillation Adjustment”, “Y OUT level Adjustment” and “C OUT level Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. G-CAM flip Adjustment Set the color reproduction conditions to optimum.
PAGE 96
2. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset. Subject Measurement Point Not required DDS display data of LCD or TV monitor (Note 3) Measuring Instrument Adjustment Page Adjustment Address Specified Value F 2F, 30 7E to 82 during IRIS OPEN (Note 1) 13 to 17 during IRIS CLOSE (Note 2) Note 1: Select page: 2, address: 01, set data: 01, and press the PAUSE button of the adjusting remote commander.
PAGE 97
3. Flange Back Adjustment The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 3-1. Flange Back Adjustment(1) Subject Measurement Point Measuring Instrument Adjustment Page Adjustment Address 3-2. Flange Back Adjustment (2) Perform this adjustment after performing “Flange Back Adjustment (1)”. Subject Flange back adjustment chart (2.
PAGE 98
4. Flange Back Check Subject Measurement Point Measuring Instrument Adjustment Page Adjustment Address 5. Picture Frame Setting Siemens star chart (2.0 m from the front of the lens) (Luminance: approx. 200 lux) Check operation on TV monitor Subject Measurement Point Measuring Instrument Specified Value F 3E to 42, 76 to 7B Color bar chart standard picture frame (1.5m from the front of the lens) Video output terminal Oscilloscope and TV monitor A=B, C=D, t=0 ± 0.
PAGE 99
6. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. Subject Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value R-Y Color bar chart standard picture frame Video output terminal Vectorscope F 34, 36, F5, F6 All color luminance points should settle within each color reproduction frame. R MG YL B-Y Switch setting: 1) NIGHT SHOT switch ......................................................
PAGE 100
7. IRIS IN/OUT Adjustment For the unit to judge if the white balance is indoors or outdoors in auto white balance operations, measure the light level and write it in the EEPROM. If the level is not correct, the white balance will not be accurate. Subject Measurement Point Measuring Instrument Adjustment Page Adjustment Address 8. MAX GAIN Adjustment Setting the minimum illumination. If it is not consistent, the image level required for taking subjects in low illuminance will not be produced (dark).
PAGE 101
9. Auto White Balance Standard Data Input Subject Adjustment Page Adjustment Address 10. Auto White Balance Adjustment Adjust to the proper auto white balance output data. If it is not correct, auto white balance and color reproducibility will be poor. Clear chart (Color bar standard picture frame) F 70 to 73 Subject Note 1: Perform “Color Reproduction Adjustment” before this adjustment. Note 2: Check that the data of page: 2, address: 02 is data: 00. If not, turn the power of the unit OFF/ON.
PAGE 102
11. White Balance Check Subject Filter Measurement Point Measuring Instrument Specified Value Clear chart (Color bar standard picture frame) Filter C14 for color temperature correction ND filter 1.0 and 0.3 video output terminal Vectorscope Fig. 5-1-11. A to C R-Y 2 mm B-Y Switch setting: 1) NIGHT SHOT switch ...................................................... OFF 2 mm Checking method: 1) Check that the lens is not covered with either filter.
PAGE 103
12. Angular Velocity Sensor Sensitivity Check (CCD-TR716/TRV43/TRV46/TRV46PK) • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts. At this time, note down also to which board it was attached to.
PAGE 104
1. EVF Initial Data Input Mode VTR stop Signal No signal Adjustment Page E Adjusting Address C2 to CD 1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT (CCD-TR416/TR416PK/TR516/TR516PK/TR716) Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to avoid electrical shock. Note 2: When replacing the LCD unit, be careful to prevent damages caused by static electricity.
PAGE 105
3. Bright Adjustment (VF-119 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). 2. VCO Adjustment (VF-119 board) Set the VCO free-run frequency. If deviated, the EVF screen will be blurred. Mode Signal Measurement point Measuring instrument Adjustment page Adjustment address Specified value VTR stop No signal Pin !∞ of CN910 (VCO) on VC-215 board Oscilloscope (DC range) E C2 A = 1.8 ± 0.
PAGE 106
4. Contrast Adjustment (VF-119 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). Mode Signal Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value 5. Backlight Consumption Current Adjustment (VF-120 board) Set the backlight luminance and color temperature. If deviated, the image may become dark or bright.
PAGE 107
1-5. MONOCHROME ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENTS Note: CCD-TR315 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/ TRV46/TRV46PK 1-5-2. Centering Adjustment 1-5-1. Horizontal Slant Check Mode Signal Specified Value Playback Alighment tape : For checking operations (WR5-5NSP) Monoscope section ± 1.
PAGE 108
1-5-4. Aberration Adjustment Mode Signal Specified Value 1-5-5. Horizontal Amplitude Adjustment (VF-99 board) VTR stop Dot pattern b1 2 • a1 b2 0.8 • a2 Mode Signal Adjusting method: 1) Adjust the aberration adjustment ring so that the tracing of the dot satisfies the specified value. 2) If the centering becomes displaced here, perform the centering adjustment from the beginning again.
PAGE 109
1-5-6. Vertical Amplitude Adjustment (VF-99 board) Mode Signal Adjusting Element Specified Value 1-5-7. Brightness Adjustments (VF-99 board) Playback Alighment tape : For checking operations (WR5-5NSP) Monoscope section RV903 10 ± 3% Mode Signal Specified Value Playback Alighment tape : For checking operations (WR5-5NSP) Monoscope section RV904 Adjusting method: 1) Rotate RV904, and adjust so that the bright/dark sections of the gray scale are displayed correctly.
PAGE 110
1-6. LCD SYSTEM ADJUSTMENT (TRV series) 1. LCD Initial Data Input Note1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to avoid electrical shock. Note2: When replacing the LCD unit, be careful to prevent damages caused by static electricity. Note3: Set the brightness to the center using the LCD BRIGHT button. Note4: LCD model: PD-107board, Ref. No.
PAGE 111
2. VCO Adjustment (PD-107 board) Set the VCO freerun frequency. If deviated, the LCD screen will be blurred. Mode VTR stop Signal No signal Measurement point Pin 2 of CN5501 (VCO VOLTAGE) of PD-107 board Measuring instrument Oscilloscope Adjustment page E Adjustment address D6 Specified value A = 2.75 ± 0.02V 3. D range Adjustment (PD-107 board) Set the D range of the RGB decoder used to drive the LCD to the specified value. If deviated, the LCD screen will become blackish or saturated (whitish).
PAGE 112
4. Bright Adjustment (PD-107 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). Mode Signal Measurement point Measuring instrument Adjustment page Adjustment address Specified value 5. Contrast Adjustment (PD-107 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish).
PAGE 113
6. V-COM Adjustment (PD-107 board) Set the common electrode drive signal level of LCD to the specified value. Mode Signal Measurement point Measuring instrument Adjustment page Adjustment address Specified value 7. Color Adjustment (PD-107 board) Set the color saturation to the standard value. If deviated, the color will be to dark or light. VTR stop No signal Pin 4 of CN5501 (PANEL COM) of PD-107 board Oscilloscope E D5 A = 6.50 ± 0.
PAGE 114
9. White Balance Adjustment (PD-107 board) Correct the white balance. If deviated, the LCD screen color cannot be reproduced. 8. V-COM Adjustment (PD-107 board) Set the DC bias of the common electrode drive signal of LCD to the specified value. If deviated, the LCD display will move, producing flicker and conspicuous vertical lines.
PAGE 115
5-2. MECHANICAL SECTION ADJUSTMENT 6) Connect the oscilloscope. Channel 1: Pin 6 of CN910 of VC-215 board External trigger: Pin !¡ of CN910 of VC-215 board Connect the oscilloscope via the CPC-7 jig (J-6082-382-A). 7) Playback the alignment tape for tracking. (WR5-1NP) 8) Check that the RF waveform of the oscilloscope is flat at both the entrance and the exit. If not flat, perform necessary adjustment according to the separate “8 mm Video Mechanical Adjustment Manual VII (B Mechanism)”.
PAGE 116
5-3. VIDEO SECTION ADJUSTMENTS When performing adjustments, refer to the layout diagrams for adjustment related parts beginning from page 5-60. 3-1. PREPARATIONS BEFORE ADJUSTMENT The following adjusting instruments are used for adjusting the video section. 3-1-1. Equipments to be Used 1) TV monitor 2) Oscilloscope: 2 phenomena, band 30 MHz or wider, with delay mode. (Use a 10:1 probe unless specified otherwise.
PAGE 117
3-1-2. Precautions on Adjusting 1) The adjustments of this unit are performed in the VTR mode or camera mode. To set to the VTR mode, set the power switch to “VTR” or set the “Forced VTR Power ON mode” using the adjusting remote commander (Note 1). To set to the Camera mode, set the power switch to “CAMERA” or set the “Forced Camera Power ON mode” using the adjusting remote commander (Note 2). After completing adjustments, be sure to exit the “Forced VTR Power ON Mode” or “Forced Camera Power ON Mode”.
PAGE 118
3-1-4. Connecting the Equipments Connect the measuring instruments as shown in Fig. 5-3-2 and perform the adjustments. Connecting the TV Monitor and Regulated Power Supply Battery terminal Main Unit TV monitor Regulated power supply 8.4±0.1Vdc VIDEO Connect when using the camera mode or playing back. VIDEO terminal Fig. 5-3-2. 3-1-5. Alignment Tape The following table lists alignment tapes which are available. Use the tape specified in the signal column for each adjustment.
PAGE 119
Note: Measure using the VIDEO terminal (Terminated at 75 Ω). Fig. 5-3-3. shows the 75% color bar signals recorded on the alignment tape. Fig. 5-3-3.
PAGE 120
3-1-6. Output Level and Impedance Video output Phono jack, 1 Vp-p, 75Ω, unbalanced, sync negative Audio output Phono jack, –7.5 dBs, (at load impedance 47 kΩ), impedance less than 2.2 kΩ 3-1-8. Service Mode Additional note on adjustment Note: After the completion of the all adjustments, cancell the service mode by either of the following ways. 1) Unplug the main power supply and remove the lithium battery. (In this case, date and time and menu setting have been set by users are canceled. Perform resetting.
PAGE 121
2-1. EMG CODE (Emergency Code) The codes shown in the following table which correspond to errors that occur are recorded in addresses 10, 14, and 18. 2.
PAGE 122
2-2. MSW Codes • The lower parts of the data of addresses 12, 16 and 1A represent the MSW codes (mode switch, mechanism position) when errors occurs. • The upper parts of the data of addresses 12, 16 and 1A represent, when the mechanism position is to be moved, the MSW codes at the start of movement (when moving the loading motor). • The lower parts of the data of addresses 13, 17 and 1B represent the MSW codes of the desired movement when the mechanism position is to be moved.
PAGE 123
3. Bit value discrimination Bit values must be discriminated using the display data of the adjusting remote commander for the following items. Use the table below to discriminate if the bit value is “1” or “0”. 4. Switch check (1) Page 3 Bit 0 1 2 3 4 5 6 7 Address 43 Function When bit value=1 When bit value=0 VTR MODE SW OFF ON CAM MODE SW OFF ON START/STOP SW OFF ON EJECT SW OFF ON CC DOWN SW OFF ON Using method: 1) Select page: 3, address: 43.
PAGE 124
5. Switch check (2) Page 3 Address 60 to 66 Using method: 1) Select page: 3, address: 60 to66. 2) By discriminating the display data, the pressed key can be discriminated.
PAGE 125
8. LED, LCD (display window) check Page 3 Address 05 9. Record of Use Check Bit5 Page 3 Address Using method: 1) Select page: 3, address: 05, and set the bit value of Bit5 to “1”. 2) Check that all LED are lit and all segments of LCD (display window) are lit. 3) Select page: 3, address: 05, and set the bit value of Bit5 to “0”.
PAGE 126
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Initialization of D, E, F Page Data If the D, E, F page data is erased due to some reason, perform “1-2. INITIALIZATION OF D, E, F PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”. 2. Battery End Adjustment (VC-215 board) Set the battery end voltage. If the voltage is incorrect, the life of the battery will shorten. The image at the battery end will also be rough.
PAGE 127
3-3. 2. RF Switching Position Adjustment (VC-215 Board) If deviated in this case causes switching noise or jitter on the played back screen. SERVO SYSTEM ADJUSTMENTS 1. CAP FG Offset Adjustment (VC-215 board) Improve the capstan servo characteristic. If it is not correct. jitters will increase. Mode Subject Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified value Mode Signal Camera recording (SP mode) Arbitrary Pin !™ of CN910 (CAP FG) Oscilloscope F 69 Duty = 50±0.
PAGE 128
3-4. VIDEO SYSTEM ADJUSTMENTS 1. 28 MHz Origin Oscillation Adjustment (VC-215 board) Set the frequency of the clock for synchronization. If deviated, the synchronization will be disrupted and the color will become inconsistent. Video system adjustments must be performed in the following order. [Adjusting Order] 1. 28MHz origin oscillation adjustment 2. AFC f0 adjustment 3. Filter f0 adjustment 4. Y OUT level adjustment 5. C OUT level adjustment 6. RP filter f0 adjustment 7.
PAGE 129
3. Filter f0 Adjustment (VC-215 board) Minimize the chroma signal residual components during composite video signal input. 2. AFC f0 Adjustment (VC-215 board) Adjust the pull-in range of the A/D converted clock generator during playback.
PAGE 130
4. Y OUT Level Adjustment (VC-215 board) Set the Y signal output level. Mode Signal Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value 5. C OUT Level Adjustment (VC-215 board) Set the chroma signal output level.
PAGE 131
6. RP Filter f0 Adjustment (VC-215 board) Adjust the LPF of the playback RF amplifier. Mode Signal Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value VTR stop No signal Pin 9 of CN910 (RF AGC OUT) Oscilloscope F 4E A = Below 10mVp-p Connection: 1) Input a 14.2MHz, 400mVp-p CW signal to Pin 7 of CN910 (RF AGC IN). Signal generator Pin 5 of CN101 of PJ-90/91 board 14.2MHz 400mVp-p 1kΩ 0.01µF 0.
PAGE 132
7. Hi8 REC Y Current Adjustment (VC-215 board) CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK Adjust the Y FM signal recording current. Mode Signal Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value 14) Write the following data in page: F, address: 57 to 5A.
PAGE 133
8. Standard8 REC Y Current Adjustment (VC-215 board) CCD-TR315/TR416/TR416PK CCD-TRV16/TRV16PK Adjust the Y FM signal recording current. Mode Signal Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value 14) Write the following data in page: F, address: 57 to 5A.
PAGE 134
9. Hi8 REC L Level Adjustment (VC-215 board) CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK Set the recording levels of the REC AFM signal and REC ATF signal. If the level is too low, the audio S/N will deteriorated, tracking will not be stable, or SP/LP will not be discriminated properly. If too high, color beets will be produced on the self-recording/playback image.
PAGE 135
10. Standard8 REC L Level Adjustment (VC-215 board) CCD-TR315/TR416/TR416PK CCD-TRV16/TRV16PK Set the recording levels of the REC AFM signal and REC ATF signal. If the level is too low, the audio S/N will deteriorated, tracking will not be stable, or SP/LP will not be discriminated properly. If too high, color beets will be produced on the self-recording/playback image.
PAGE 136
11. REC C Current Adjustment (VC-215 board) Set the recording current levels of the REC Chroma signal. If it is too low, chroma signal noise in played back picture will increased. If too high, Y signal noises will increase and white modulation noises will be produced. Mode Signal Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value 14) Select page: 0, address: 01, and set data: 01.
PAGE 137
3-5. 2. IR Video Deviation Adjustment (VC-215 board) IR TRANSMITTER ADJUSTMENTS (CCD-TRV43/TRV46/TRV46PK) Mode Subject Measurement Point Adjust using a IR receiver jig (J-6082-383-A). Switch setting: LASER LINK .................... (Red LED is lit) Measuring Instrument Adjustment Page Adjustment Address Specified Value 1.
PAGE 138
3. IR Audio Deviation Adjustment (VC-215 board) Mode Signal Measurement Point Measuring Instrument Adjustment Page Adjustment Address Specified Value VTR recording Audio signal : 400Hz, –7.5dBs : AUDIO terminal Video signal : Color bar signal : VIDEO terminal AUDIO terminal of IR receiver jig ( Terminated at 47kΩ) Audio level meter F 67 Signal level: –7.5±2.0dBs Connection of Equipment Connect the measuring device as shown in the following figure, and adjust.
PAGE 139
3-6. AUDIO SYSTEM ADJUSTMENT 1. 1.5 MHz Deviation Adjustment (VC-215 board) Adjust to the optimum audio FM signal distortion. If the adjustment is not correct, its playback level will differ from that of other units. [Connecting the measuring instruments for the audio] Connect the audio system measuring instruments besides the video system measuring instruments as shown Fig. 5-3-25. Mode Signal • Connection of Audio generator and attenuator.
PAGE 140
3-7.
PAGE 141
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. The components identified by mark ! or dotted line with mark ! are critical for safety.
PAGE 142
6-1-2. CABINET (L) AND BATTERY PANEL ASSEMBLY 55 70 not supplied 71 51 73 56 72 not supplied not supplied not supplied 54 J901 74 See page 6-6 69 53 51 65 64 61 63 52 62 not supplied 68 60 52 52 59 S003 67 66 57 J001 51 58 51 Ref. No. Part No. Description Remark Ref. No.
PAGE 143
6-1-3. FRONT PANEL BLOCK ASSEMBLY Video light model CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK No video light CCD-TR315/TR416/TR416PK model CCD-TRV16/TRV16PK 110 101 5 -3446 A 3 M 102 110 110 not supplied not supplied 109 110 107 not supplied not supplied 108 106 105 No video light models 104 VL901 LAMP,HALOGEN XB-3D(DC6V/3W) MIC901 103 Video light models Ref. No. 101 101 101 101 101 101 102 102 102 Part No.
PAGE 144
6-1-4. CABINET (R) BLOCK ASSEMBLY (TR series) 154 161 166 157 161 164 161 161 161 153 161 161 161 155 161 156 165 165 151 not supplied 161 See pages 6-7 to 6-8 161 161 C 0 F-6 160 152 163 158 162 LCD903 B/W view finder model Color view finder model Ref. No. 151 152 152 152 153 * 154 155 156 157 158 CCD- TR315 CCD- TR416/TR416PK/TR516/ TR516PK/TR716 159 Part No.
PAGE 145
6-1-5. CABINET (R) BLOCK ASSEMBLY (TRV series) 166 161 157 161 154 161 161 -61 158 CF 161 161 164 161 155 161 161 153 156 165 165 151 See page 6-8 not supplied 161 161 not supplied SP901 160 160 167 163 152 162 See page 6-9 159 Ref. No. 151 152 152 152 153 * 154 155 156 157 158 159 Part No. Description 161 Remark 161 Ref. No.
PAGE 146
6-1-6. MAIN BOARDS BLOCK ASSEMBLY Video light model CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK No video light CCD-TR315/TR416/TR416PK model CCD-TRV16/TRV16PK See page 6-10 214 214 201 not supplied No video light models 214 215 204 214 DD -11 7 205 VC -21 214 214 5 210 214 207 214 Video light models 211 SE452 208 209 212 206 206 214 See pages 6-11 to 6-13 202 214 SE451 213 203 CCD-TR716 & TRV series Ref. No.
PAGE 147
6-1-7. COLOR EVF BLOCK ASSEMBLY (Color View Finder models CCD-TR416/TR416PK/TR516/TR516PK/TR716) Note : As for the model whitch carries a B/W view finder, refer to page 6-8. 253 254 252 251 VF -11 9 262 255 256 LCD902 257 not supplied 261 ND5351 258 259 260 not supplied 262 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. 251 252 253 254 255 * 256 257 258 Part No.
PAGE 148
6-1-8. B/W EVF BLOCK ASSEMBLY (B/W View Finder models CCD-TR315 and TRV series) Note : As for the model whitch carries a color view finder, refer to page 6-7. 301 310 303 302 304 306 305 307 VF 312 -99 V901 311 308 309 304 313 304 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No.
PAGE 149
6-1-9. LCD BLOCK ASSEMBLY (TRV series) 351 ND801 353 354 359 352 PD -10 7 LCD901 357 LCD903 364 362 362 355 363 356 358 365 366 367 361 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No.
PAGE 150
6-1-10. ZOOM LENS BLOCK ASSEMBLY 411 414 not supplied 403 409 406 404 405 M906 407 403 412 402 M905 IC401 410 402 408 402 401 415 415 413 Be sure to read “Note on the CCD Imager replacement” on page 4–8 when changing the CCD imager. Ref. No. Part No. Description Remark Ref. No. 401 402 403 404 8-848-722-01 3-713-791-51 3-713-791-41 3-979-029-01 DEVICE, LENS (LSV-600A) SCREW (M1.7 x 3.5), TAPPING, P2 SCREW (M1.
PAGE 151
6-1-11. CASSETTE COMPARTMENT ASSEMBLY 704 708 708 711 705 706 703 709 707 708 712 702 See page 6-13 710 701 See page 6-12 Ref. No. Part No. Description 701 702 703 704 705 A-7040-421-A 7-624-102-04 X-3949-153-2 3-965-587-03 3-965-584-08 DAMPER ASSY STOP RING 1.5, TYPE -E CASSETTE COMPARTMENT ASSY SPRING (POWER, TENSION), TENSION RETAINER, GOOSENECK 706 3-976-055-01 SCREW (M1.4X1) Remark Ref. No. 6-11 Part No.
PAGE 152
6-1-12. LS CHASSIS ASSEMBLY 762 793 772 771 S002 778 779 S001 773 761 A 760 782 776 765 FP-249 (not supplied) 781 777 774 767 D001 758 780 775 784 769 769 785 766 770 768 778 759 783 758 786 787 758 757 758 789 752 753 788 754 756 751 Ref. No. 755 Part No.
PAGE 153
6-1-13. MECHANISM CHASSIS ASSEMBLY M901 817 809 809 810 812 823 805 81 1 806 M903 814 813 808 807 828 830 813 821 803 831 815 837 825 819 816 805 M902 824 815 805 820 826 836 S901 835 804 not supplied 809 829 827 814 822 818 802 832 801 not supplied 808 833 834 Ref. No. Part No. Description Remark 801 802 803 804 805 X-3947-343-1 3-965-550-02 1-657-785-11 3-965-545-01 3-965-549-01 GROUND (IM) ASSY, SHAFT SCREW (M1.7X1.
PAGE 154
CD-210/211 6-2. CF-60/61 ELECTRICAL PARTS LIST Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. When indicating parts by reference number, please include the board name. Ref. No. Part No.
PAGE 155
CF-60/61 Ref. No. Part No. Description Remark Ref. No. < TRANSISTOR > Q001 S010 8-729-402-42 TRANSISTOR UN5213-TX (TR315/TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) S010 S012 Part No.
PAGE 156
DD-117 Ref. No. Part No. Description C811 C812 C813 C815 C817 1-162-965-11 1-162-964-11 1-162-964-11 1-162-964-11 1-113-991-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP 0.0015uF 0.001uF 0.001uF 0.001uF 33uF Remark C818 C819 C820 C821 C823 1-163-038-91 1-162-964-11 1-162-964-11 1-162-964-11 1-115-566-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.001uF 0.001uF 0.001uF 4.7uF C824 C825 C826 1-115-566-11 CERAMIC CHIP 4.
PAGE 157
DD-117 Ref. No. Part No. Description Remark Ref. No. < COIL > Q815 Q819 L804 1-412-056-11 INDUCTOR CHIP 4.
PAGE 158
DD-117 Ref. No. Part No. Description Remark Ref. No. Q856 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3) R852 Q932 8-729-037-74 TRANSISTOR UN9213J-(K8).SO (TRV43/TRV46/TRV46PK) 8-729-042-29 TRANSISTOR RN1104F(TPL3) (TRV43/TRV46/TRV46PK) R853 Q932 < RESISTOR > METAL CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 47K 82K 10K 22K 15K 5% 0.
PAGE 159
FP-355 FP-249 Ref. No. Part No. Description Remark 1-218-895-11 RES,CHIP R901 R902 R903 1-218-887-11 RES,CHIP 47K 0.50% 1/16W 1-216-864-11 METAL CHIP 0 5% 1/16W 1-216-845-11 METAL CHIP 100K 5% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) 1-216-849-11 METAL CHIP 220K 5% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) 1-218-901-11 RES,CHIP 180K 0.50% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) R904 R905 100K Ref. No. R900 Part No. 0.
PAGE 160
MA-345/346 Ref. No. Part No. Description Remark Ref. No. A-7073-782-A MA-345(B) BOARD, COMPLETE ************************* (TR516/TR516PK/TR716) D333 A-7073-820-A MA-345(SL) BOARD, COMPLETE ************************** (TR315/TR416/TR416PK) (Ref.No. 9,000 Series) ! F301 A-7073-823-A MA-346(VZB) BOARD, COMPLETE *************************** (TRV36/TRV36PK) A-7073-873-A MA-346(VZL) BOARD, COMPLETE *************************** (TRV16/TRV16PK) (Ref.No. 4,000 Series) < CAPACITOR > 1-107-686-11 TANTAL.
PAGE 161
PD-107 MA-345/346 Ref. No. Part No. Description R312 1-216-864-11 METAL CHIP R313 1-216-864-11 METAL CHIP Remark Ref. No. 0 Part No. Description Remark 5% 1/16W (TRV43/TRV46/TRV46PK) 0 5% 1/16W C5616 C5618 C5619 1-107-682-11 CERAMIC CHIP 1-113-994-11 TANTAL. CHIP 1-162-970-11 CERAMIC CHIP 1uF 6.8uF 0.
PAGE 162
PD-107 Ref. No. Part No. Description Remark Q5606 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX Q5607 Q5608 Q5701 Q5702 8-729-230-63 8-729-420-24 8-729-039-43 8-729-015-74 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Ref. No. 2SD1819A-QRS-TX 2SB1218A-QRS-TX FP216-TL UN5111-TX < RESISTOR > Part No.
PAGE 163
PJ-90 Ref. No. Part No. Description Remark Ref. No. C466 < DIODE > D102 D103 8-719-062-16 DIODE 01ZA8.2(TPL3) 8-719-062-16 DIODE 01ZA8.2(TPL3) Description VC-215 Remark 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V (TR716/TRV43/TRV46/TRV46PK) < CONNECTOR > < JACK > J101 Part No.
PAGE 164
VC-215 Ref. No. Part No. Description Remark Ref. No. A-7094-112-A VC-215(ZSL0) BOARD, COMPLETE (TR315) **************************** A-7094-117-A VC-215(VZB0) BOARD, COMPLETE ***************************** (TRV36/TRV36PK) A-7094-118-A VC-215(VMMIB0) BOARD, COMPLETE ****************************** (TRV43/TRV46/TRV46PK) A-7094-179-A VC-215(ZLCO) BOARD, COMPLETE **************************** (TR416/TR416PK) A-7094-204-A VC-215(VZLO) BOARD, COMPLETE **************************** (TRV16/TRV16PK) (Ref.No.
PAGE 165
VC-215 Ref. No. Part No. Description Remark Ref. No. C233 C234 C235 1-162-638-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1uF 0.01uF 0.01uF C237 C239 C245 C246 C247 1-164-156-11 1-115-156-11 1-162-970-11 1-162-970-11 1-162-638-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 1uF 0.01uF 0.
PAGE 166
VC-215 Ref. No. Part No. Description Remark C522 C523 1-107-826-91 CERAMIC CHIP 1-115-467-11 CERAMIC CHIP 0.1uF 0.22uF 10% 10% 16V 10V C524 C525 C526 C527 C528 1-162-962-11 1-162-970-11 1-107-826-91 1-107-826-91 1-109-982-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 470PF 0.01uF 0.1uF 0.1uF 1uF 10% 10% 10% 10% 10% 50V 25V 16V 16V 10V C529 C530 C531 C552 C553 1-107-826-91 1-107-826-91 1-104-752-11 1-162-968-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP TANTAL.
PAGE 167
VC-215 Ref. No. Part No. Description Remark Ref. No. CN908 1-774-639-21 CONNECTOR, FFC/FPC 15P CN909 1-764-703-11 CONNECTOR, FFC/FPC (LIF) 4P (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) CN910 1-766-346-21 CONNECTOR, FFC/FPC 16P CN911 1-785-760-21 CONNECTOR, FFC/FPC (ZIF) 45P CN915 1-774-600-41 CONNECTOR, BOARD TO BOARD 70P CN916 1-766-348-21 CONNECTOR, FFC/FPC 18P Part No.
PAGE 168
VC-215 Ref. No. Part No. Description Remark Q044 Q151 8-729-042-29 TRANSISTOR RN1104F(TPL3) 8-729-037-61 TRANSISTOR RN2104F(TPL3) Q153 Q202 Q203 Q204 Q205 8-729-040-77 8-729-037-52 8-729-037-53 8-729-037-52 8-729-037-74 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Ref. No. 2SC5376-B(TE85L) 2SC4738F-Y/GR(TPL3) 2SA1832F-Y/GR(TPL3) 2SC4738F-Y/GR(TPL3) UN9213J-(K8).SO Q205 Q208 Q208 Q213 8-729-042-29 TRANSISTOR RN1104F(TPL3) 8-729-037-74 TRANSISTOR UN9213J-(K8).
PAGE 169
VC-215 Ref. No. Part No.
PAGE 170
VC-215 Ref. No. R377 R378 R379 R382 R383 R384 R385 R386 Part No. Description Remark 1-216-852-11 METAL CHIP 390K 5% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) 1-216-837-11 METAL CHIP 22K 5% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) 1-216-837-11 METAL CHIP 22K 5% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) 1-216-829-11 METAL CHIP 4.7K 5% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) 1-216-826-11 METAL CHIP 2.
PAGE 171
VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R565 1-216-833-11 METAL CHIP 10K 5% 1/16W R649 1-216-857-11 METAL CHIP 1M 5% 1/16W R566 R567 R569 R570 R571 1-216-835-11 1-216-825-11 1-216-825-11 1-216-841-11 1-216-837-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 15K 2.2K 2.
PAGE 172
VC-215 Ref. No. VF-99 Part No. Description R768 1-216-847-11 METAL CHIP R770 1-216-847-11 METAL CHIP R771 1-216-818-11 METAL CHIP R772 Remark 6.
PAGE 173
VF-99 Ref. No. Part No. Description R910 R911 R912 R916 R917 1-216-835-11 1-216-160-00 1-216-857-11 1-218-879-11 1-218-891-11 METAL CHIP RES,CHIP METAL CHIP RES,CHIP RES,CHIP R918 R919 R920 R921 1-216-829-11 METAL CHIP 4.7K 5% 1/16W 1-216-843-11 METAL CHIP 68K 5% 1/16W 1-216-837-11 METAL CHIP 22K 5% 1/16W 1-216-800-11 RES,CHIP 18 5% 1/16W (TR315/TRV16/TRV16PK/TRV36/TRV43/TRV46/TRV46PK) 1-216-795-11 RES,CHIP 6.
PAGE 174
VF-119 Ref. No. VF-120 VL-21/22 Part No. Description R5446 R5447 R5448 R5449 1-216-837-11 1-216-833-11 1-216-839-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 10K 33K 0 5% 5% 5% 5% Remark 1/16W 1/16W 1/16W 1/16W R5452 R5458 R5460 R5471 R5473 1-216-821-11 1-216-864-11 1-216-864-11 1-216-837-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 0 0 22K 0 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R5476 1-216-864-11 METAL CHIP 0 5% 1/16W Ref. No.
PAGE 175
Ref. No. Part No. Description Remark Ref. No.
PAGE 176
Take a copy CAMERA COLOR REPRODUCTION FRAME and Parts reference sheets with a clear sheet for use. FOR CAMERA COLOR REPRODUCTION ADJUSTMENT CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK < PARTS REFERENCE SHEET > You can find the parts position of mount locations applying to boards of a set.
PAGE 177
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK Sony Corporation 9-974-124-11 Personal A&V Products Company – 290 – 98L0931-1 Printed in Japan © 1998. 12 Published by Quality Engineering Dept.