CODE SEARCH VCR TV SAT POWER DVD AUX CHAN PAGE VOL VOL SUBTITLE REPEAT PAGE FLASHBK RATIO DATE CHAN SURF SIGNAL IN PUT HELP SD/HD 1 2 3 4 5 6 7 8 9 0 INFO GUIDE OK MENU EXIT SCAN SKIP PLAY SCAN REC STOP PAUSE ZRF1
Table of Contents Introduction ...................................................... 3 Setup ............................................................... 4 Battery Installation ....................................... 4 Battery Saver ............................................... 4 Code Saver ................................................. 4 Power-On default ........................................ 4 TV Punch Through Feature .......................... 5 VCR/DVD Punch Through Feature ..............
Setup Setup, cont. Battery Installation TV Volume/Mute Punch-Through Feature 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries. 3. Press the battery cover back into place. The TV Volume/Mute punch-through feature lets you control the Volume and Mute function of your TV in any mode programmed to be a VCR, DVD, CABLE or SAT device, without needing to change to TV mode.
Button Functions, cont. Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.G. FLASHBK may be called RECALL, or ENTER may be called DISPLAY. These differences depend on the brand and model of your product. Also, this remote can only operate features that exist on your product. E.G., your product must have FLASHBK ability for the FLASHBK button to operate this feature. Red Indicator Lights when any button is pressed.
Advanced Functions DASH (-) Used to enter a channel number for multiple channels such as 2-1, 2-2, etc. A broadcaster may transmit multiple programs on a single channel. Multiple programs are distinguished by a unique sub-channel number, separated by a dash (-). SEL (SELECT) Use with numbered buttons for instant channel selection. When you press a channel number, for example 22, the receiver awaits another button press for three seconds and then tunes to 22. SURF Shows the list of your Surf channels.
Advanced Functions, cont. Advanced Functions, cont. DVD Functions VCR/DVD Punch Through Feature SCAN+ and SCAN- buttons control the speed of Fast Forward and Reverse Playback respectively. This remote lets you Punch-through to the last VCR or DVD device used. Normally other types of remotes only punch-through (from another Mode) on the 6 VCR buttons, to the device programmed under the VCR Mode button. This is not much use if you are using a DVD programmed under a Mode other than VCR.
Code Entry Code Entry, cont. Direct Code Entry Programming with Code Search 1. Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button. 2. Press and release the desired mode button ( TV, VCR , etc.). The red indicator blinks, then stays lit. 3. Enter the 3 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. 4.
Code Entry, cont. Code Entry, cont. VCR TV 3. SAT DVD VOL VOL RATIO 4. SURF SIGNAL INPUT 2 3 4 5 6 7 8 9 14 ALL N/A N/A ALL ALL N/A ALL ALL N/A 0 N/A PIONEER, TEAC, NAD KENWOOD, YAMAHA, DENON, ONKYO N/A N/A N/A N/A 9 SD/HD 1 N/A N/A DATE HELP N/A N/A 8 6. PAGE CHAN SYLVANIA, CURTISMATHES, FISHER, EMERSON, OPTIMUS 7 5.
Product Operation Code Identification Code Identification Feature The Code Identification Feature allows you to identify the three digit library code stored under your device key. For example, if you want to find out what three digit code is stored under your TV device key, follow the six steps below: 1. Press and hold the CODE SEARCH button until the red indicator stays on. Release the CODE SEARCH button. 2. Press and release the desired mode button (TV, VCR , etc.).
Wireless Receiver Troubleshooting The remote transmits wireless Radio Frequency (RF) commands. The wireless receiver (included) receives these commands and converts them to regular Infrared (IR) commands. These IR commands are then emitted from the IR Extender (also included) to control your A/V components. This lets you control your A/V components from ANY room in your home - you don’t need to aim the remote at your component! Remote does not operate your product.
90 Day Warranty This product is manufactured to ZENITH specifications and is free from defects in material, workmanship and assembly. This warranty extends only to the original purchaser and is nontransferable. Should a defect occur under normal operating conditions within 90 days from the date of purchase, ZENITH will provide a comparable replacement free of charge within the warranty period, to the original purchaser.
