Trademarks ® ® ® ® ® ® Autel , MaxiSys , MaxiDAS , MaxiScan , MaxiTPMS , MaxiRecorder , and ® MaxiCheck are trademarks of Autel Intelligent Technology Corp., Ltd., registered in China, the United States and other countries. All other marks are trademarks or registered trademarks of their respective holders.
Safety Information For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions herein presented throughout this manual be read and understood by all persons operating, or coming into contact with, the device. There are various procedures, techniques, tools, and parts for servicing vehicles, as well as in the skill of the person doing the work.
Safety Information Important Safety Instructions Do Not Turn the Volume Up Too Loud When Using Headphones Listening at high volumes that over-stimulate the ear for long periods of time may result in loss of hearing. SAFETY WARNINGS: Always perform automotive testing in a safe environment. Wear safety eye protection that meets ANSI standards. Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
Contents SAFETY INFORMATION ............................................................................................. I CHAPTER 1 USING THIS MANUAL ...................................................................... 1 1.1 CONVENTIONS .................................................................................................... 1 1.1.1 Bold Text .................................................................................................. 1 1.1.2 Terminology ...............................
CHAPTER 4 DIAGNOSTICS OPERATIONS ........................................................... 19 4.1 ESTABLISHING VEHICLE COMMUNICATION .............................................................. 19 4.1.1 Vehicle Connection ................................................................................ 19 4.1.2 VCI Connection ...................................................................................... 21 4.1.3 No Communication Message ..........................................................
.1 NAVIGATION..................................................................................................... 66 6.1.1 Terminology ........................................................................................... 68 6.2 OPERATIONS..................................................................................................... 69 6.2.1 Home ..................................................................................................... 70 6.2.2 Search Fix Features....................
12.3 12.4 12.5 12.6 12.7 12.8 MY ACCOUNT ............................................................................................... 98 USER COMPLAINT .......................................................................................... 98 DATA LOGGING ............................................................................................ 101 COMMUNITIES ............................................................................................ 102 TRAINING CHANNELS .........................
Chapter 1 Using This Manual This manual contains device usage instructions. Some illustrations shown in this manual may contain modules and optional equipment that are not included on your system. Contact your sales representative for availability of other modules and optional tools or accessories. 1.1 Conventions The following conventions are used. 1.1.1 Bold Text Bold emphasis is used to highlight selectable items such as buttons and menu options. Example: Tap OK. 1.1.
Using This Manual Conventions 1.1.5 Procedures An arrow icon indicates a procedure. Example: To use the camera: 1 Tap the Camera button. The camera screen opens. 2 Focus the image to be captured in the view finder. 3 Tap the blue circle. The view finder now shows the captured picture and auto-saves the taken photo.
Chapter 2 General Introduction ® ® The MaxiSys /MaxiSys Pro Diagnostic Platform is an evolutionary smart solution for specialized automotive diagnosis. Utilizing the powerful A9 quad-core 1.40GHz processor, and a 9.
General Introduction MaxiSys Display Tablet Figure 2-2 MaxiSys Tablet Back View 1. Audio Speaker 2. Collapsible Stand – extends from the back to allow hands-free viewing of the display tablet at a 30 degree angle 3. Camera Lens 4. Camera Flash Figure 2-3 MaxiSys Tablet Left Side 1. Mini SD (secure digital) Card Slot - optional module 2. Mini USB (universal serial bus) OTG Port 3.
General Introduction MaxiSys Display Tablet Figure 2-4 MaxiSys Tablet Top View 1. DC Power Supply Input Port 2. Ethernet Port 3. HDMI (high-definition multimedia interface) Port 4. USB Port 5. VGA (video graphics array) Port 6. Lock/Power Button – turns the MaxiSys tool on and off with long press, or locks the screen with short press 2.1.
General Introduction MaxiSys Display Tablet 2.1.3 Technical Specifications Item Description Operating System Android Processor Samsung Exynos Quad-Core Processor 1.4GHz Memory 2GB RAM & 32GB On-board Memory Display 9.7 inch LED capacitive touch screen with 1024x768P resolution Connectivity TM 4.0, Ice Cream Sandwich Ethernet: RJ45 Ethernet Connection WiFi (802.11 a/b/g/n) USB: 2.0 BT v.2.1 + EDR Camera (rear) Rear-facing, 5.
General Introduction 2.2 VCI – Wireless Diagnostic Interface VCI – Wireless Diagnostic Interface 2.2.1 Functional Description Figure 2-5 Wireless Diagnostic Interface – for MaxiSys 1. Vehicle Data Connector (DB15-Pin) 2. Power LED - illuminates solid green when powered on 3. Vehicle LED - flashes green when communicating with the vehicle’s network 4. Error LED - illuminates solid red when serious hardware failure occurs; also flashes red when performing software/firmware update 5.
General Introduction VCI – J2534 ECU Programming Device 2.2.2 Technical Specifications Item Communications Description BT V.2.1 + EDR USB 2.0 Wireless Frequency 2.4 GHz Input Voltage Range 12 VDC Supply Current 200 mA @ 12 VDC Operating Temperature 0°C to 50°C (ambient) Storage Temperature -20°C to 70°C (ambient) Dimensions (L x W x H) 147.5 mm (5.80”) x 85.5 mm (3.37”) x 29.0 mm (1.14”) Weight 0.215 kg (0.473 lb) 2.2.
General Introduction VCI – J2534 ECU Programming Device 1. Ethernet Port 2. USB Port 3. Power LED - illuminates solid green when powered on 4. Error LED - illuminates solid red when serious hardware failure occurs 5. BT LED - illuminates solid green when connected with the MaxiSys display tablet through BT communication 6. Ethernet LED - illuminates solid green when connected with the MaxiSys display tablet or an existing LAN via the Ethernet serial cable 7.
General Introduction VCI – J2534 ECU Programming Device 2.3.2 Power Sources The J2534 programming device can receive power from both of the following sources: Vehicle Power AC/DC Power Supply Vehicle Power The J2534 programming device operates on 12-volt vehicle power, which it receives through the vehicle data connection port. The device powers on whenever it is connected to an OBD II/EOBD compliant data link connector (DLC).
General Introduction 2.4 Accessory Kit Accessory Kit 2.4.1 Main Cable The VCI device can be powered through the Main Cable when connected to an OBD II/EOBD compliant vehicle. The Main Cable connects the VCI device to the vehicle’s data link connector (DLC), through which the VCI device can transmit vehicle data to the MaxiSys display tablet. Figure 2-7 Main Cable – 1.5 m in length 2.4.2 OBD I Adapters The OBD I adapters are for Non-OBD II vehicles.
General Introduction PSA-2 Accessory Kit Benz-38 VW/Audi-2+2 Mitsubishi/Hyund ai-12+16 2.4.3 Other Accessories Standard 2.0 USB Cable Connects the display tablet to the VCI unit. Mini USB Cable Connects the display tablet to the PC. AC/DC External Power Adapter Connects the display tablet to the external DC power port for power supply. Compact Disc (CD) Includes the User Manual, Printing Services Program and Update Application, etc.
Chapter 3 Getting Started Make sure the MaxiSys Display Tablet has a charged battery or is connected to the DC power supply (see 2.1.2 Power Sources on page 5). 3.1 Powering Up Press the Lock/Power button on the top right side of the display tablet to switch the unit on. The system boots up, and shows the lock screen. Press and drag the inner ring to the edge of the circle to unlock the screen; the MaxiSys Job Menu is shown. Figure 3-1 Sample MaxiSys Job Menu 1. Application Buttons 2.
Getting Started Powering Up 3.1.1 Application Buttons The Application buttons configure the MaxiSys for the type of operation or activity to be performed. The table below gives brief descriptions of the available applications. Use the stylus pen or your finger tip to select an application from the Job Menu. Table 3-1 Applications Name Button Description Diagnostics Configures the unit to operate as a diagnostic tool. See Diagnostics Operations on page 19.
Getting Started Name Powering Up Button Description Training Allows you to store and play technical tutorial and training videos about the device usage or vehicle diagnostic techniques. See Training Operations on page 106. Quick Link Provides associated website bookmarks to allow quick access to product update, service, support and other information. See Quick Link Operations on page 108.
Getting Started Powering Up Name Button Description Camera Opens the camera with short press; takes and saves screenshot image with long press. The saved files are auto-stored in the Data Manager application for later reviews. See Data Manager Operations on page 61. Display & Sound Allows you to adjust the brightness of the screen and the volume of the audio output. VCI Opens the VCI Manager application.
Getting Started 3.2 Powering Down Powering Down All vehicle communications must be terminated before shutting down the MaxiSys display tablet. A warning message displays if you attempt to shut down while the VCI unit is communicating with the vehicle. Forcing a shut down while communicating may lead to ECM problems on some vehicles. Exit the Diagnostics application before powering down. To power down the MaxiSys tablet: 1. Press and hold the Lock/Power Button. 2.
Getting Started Installing Computer Software installation wizard will load momentarily. 2. Click on Next on the welcome page. 3. Click the Change button, and select a destination folder to install the program, and click Next to continue. Or directly click Next to continue without changing the default installation folder. 4. Click Install and the Setup.exe program will be installed onto the computer. 3.3.
Chapter 4 Diagnostics Operations By establishing a data link to the electronic control systems of the vehicle being serviced through the VCI device, the Diagnostics application allows you to retrieve diagnostic information, view live data parameters, and perform active tests. The Diagnostics application can access the electronic control module (ECM) for various vehicle control systems, such as engine, transmission, antilock brake system (ABS), airbag system (SRS) and more. 4.
Diagnostics Operations Establishing Vehicle Communication OBD II Vehicle Connection This type of connection only requires the main cable without any additional adapter. To connect to an OBD II vehicle 1. Connect the main cable’s female adapter to the Vehicle Data Connector on the VCI device, and tighten the captive screws. 2. Connect the cable’s 16-pin male adapter to the vehicle’s DLC, which is generally located under the vehicle dash.
Diagnostics Operations Establishing Vehicle Communication To connect the cigarette lighter 1. Plug the DC power connector of the cigarette lighter into the DC power supply input port on the device. 2. Connect the male connector of the cigarette lighter into the vehicle’s cigarette lighter receptacle. To connect the clipper cable - for MaxiSys Pro only 1. Connect the tubular plug of the clipper cable to the male connector of the cigarette lighter.
Diagnostics Operations Establishing Vehicle Communication Pairing Up via BT Among all methods, BT pairing is recommended as the first choice for the communication between the MaxiSys display tablet and the VCI device. The working range for BT communication is about 755 feet (230 m); this means you can perform vehicle diagnosis freely around the workshop with greater convenience.
Diagnostics Operations Establishing Vehicle Communication USB Cable Connection The USB cable connection is a simple and quick way to establish communication between the MaxiSys display tablet and the VCI device.
Diagnostics Operations 6. Establishing Vehicle Communication If Manual is selected, you need to set the IP address on your own. NOTE: If you are not sure about the specific IP address values, please contact your network administrator. 7. Tap Apply to set up the wired network connection. When the wired network is successfully connected, the connection status is displayed as Connected, and the two status lights at the corners alongside the Ethernet Ports on the display tablet illuminate.
Diagnostics Operations B. 4.2 Getting Started In case of wired connection, check the cable connection between the display tablet and the VCI device. Check if the green LED on the VCI device is illuminated for BT, Ethernet, or USB.
Diagnostics Operations Getting Started Figure 4-2 Sample Vehicle Menu Screen 1. Top Toolbar Buttons 2. Manufacturer Buttons Top toolbar Buttons The operations of the Toolbar buttons at the top of the screen are listed and described in the table below: Table 4-1 Top Toolbar Buttons Name Button Description Home Returns to the MaxiSys Job Menu. VIN Scan Touching this button opens a dropdown list; tap Auto Detect for auto VIN detection; tap Manual Input to enter VIN manually.
Diagnostics Operations Name Vehicle Identification Button Description Europe Displays the European vehicle menu. Asia Displays the Asian vehicle menu. Domestic Displays the Domestic vehicle menu. Search Touching this button opens the virtual keyboard, allowing you to manually enter the specific vehicle make required. Cancel Touching this button exits the search screen, or cancels an operation. Manufacturer Buttons The Manufacturer buttons display the various vehicle logos and the brand names.
Diagnostics Operations Vehicle Identification To perform Auto VIN Scan 1. Tap the Diagnostics application button from the MaxiSys Job Menu. The Vehicle Menu displays. (Figure 4-2) 2. Tap the VIN Scan button on the top toolbar. 3. Select Auto Detect. The tester starts VIN scanning on the vehicle’s ECU. Once the test vehicle is successfully identified, the system will guide you to the Vehicle Diagnostics screen directly.
Diagnostics Operations Vehicle Identification Select Automatic Selection and the system will proceed to acquire VIN information automatically or allow users to input the VIN manually. 4.3.2 Manual VIN Input For some vehicles that do not support the Auto VIN Scan function, the MaxiSys diagnostic system allows you to enter the vehicle VIN manually, or simply take a photo of the VIN sticker for quick vehicle identification. To perform Manual VIN Input 1.
Diagnostics Operations Navigation Step-by-step Vehicle Selection This mode of vehicle selection is menu driven; you simply follow the screen prompts and make a series of choices. Each selection you make advances you to the next screen. A Back button at the lower right corner of the screen returns you to the previous screen. Exact procedures may vary somewhat by various vehicles being serviced. 4.3.
Diagnostics Operations Navigation 1. Diagnostics Toolbar 2. Status Information Bar 3. Main Section 4. Functional Buttons Diagnostics Toolbar The Diagnostics toolbar contains a number of buttons that allow you to print or save the displayed data and make other controls. The table below provides a brief description for the operations of the Diagnostics toolbar buttons: Table 4-2 Diagnostics Toolbar Buttons Name Button Description Home Returns to the MaxiSys Job Menu.
Diagnostics Operations Name Button Navigation Description Data Logging Records the communication data and ECU information of the test vehicle. The saved data can be reported and sent to the technical center via the internet. You can go to the Support application to follow up the processing progress, see Data Logging on page 101 for detailed information. Send Tapping this button submits the Data Logging report to the technical center via the internet. To perform data printing in Diagnostics 1.
Diagnostics Operations Navigation Status Information Bar The Status Information Bar at the top of the Main Section displays the following items: 1. Menu Title – indicates the menu subject of the Main Section 2. VCI Icon – indicates the communication status between the tablet and the VCI device 3. Battery Icon – indicates the battery status of the VEHICLE Main Section The Main Section of the screen varies depending on the stage of operations.
Diagnostics Operations Main Menu Error Messages Error messages inform you when a system or procedural error has occurred. Examples of possible errors include a disconnected cable or communication interruption due to certain reasons. 4.4.3 Making Selections The Diagnostics application is a menu driven program that presents a series of choices one at a time. As you select from a menu, the next menu in the series displays. Each selection narrows the focus and leads to the desired test.
Diagnostics Operations 4.6 Diagnosis Diagnosis There are two options available when accessing the Diagnosis section: 1. Auto Scan – starts auto scanning for all the available systems on the vehicle 2. Control Units – displays a selection menu of all available control units of the test vehicle Auto Scan The Auto Scan function performs a comprehensive scanning over all the systems on the vehicle’s ECU in order to locate fault systems and retrieve DTCs.
Diagnostics Operations Diagnosis 3. Progress Bar – indicates the test progress Main Section A. List Tab Column 1 - displays the system numbers Column 2 - displays the scanned systems Column 3 - displays the diagnostic marks indicating different conditions of the test result: -!-: Indicates that the scanned system may not support the code reading function, or there is a communication error between the tester and the control system.
Diagnostics Operations Diagnosis Table 4-3 Functional Buttons in Auto Scan Name Description Back Returns to the previous screen or exit Auto Scan. Pause Suspends scanning and changes to show the Continue button. OK Confirms the test result, and continues to the system diagnosis after selecting the required system by tapping the item in the Main Section. Quick Erase Deletes codes. A warning message screen will display to inform you of possible data loss when this function is selected.
Diagnostics Operations Diagnosis The Function Menu options vary slightly by different vehicles. The function menu may include: ECU Information – provides the retrieved ECU information in detail. Selecting opens an information screen. Read Codes – displays detailed information of DTC records retrieved from the vehicle control module. Erase Codes – erases DTC records and other data from the ECM. Live Data – retrieves and displays live data and parameters from the vehicle’s ECU.
Diagnostics Operations Diagnosis sample ECU Information screen displays as below: Figure 4-9 Sample ECU Information Screen 1. Diagnostics Toolbar Buttons – see Table 4-2 Diagnostics Toolbar Buttons on page 31 for detailed descriptions of the operations for each button. 2. Main Section – the left column displays the item names; the right column shows the specifications or descriptions. 3.
Diagnostics Operations Diagnosis Figure 4-10 Sample Read Codes Screen 1. Diagnostics Toolbar Buttons – see Table 4-2 Diagnostics Toolbar Buttons on page 31 for detailed descriptions of the operations for each button. 2. Main Section 3. Code Column – displays the retrieved codes from the vehicle. Status Column – indicates the status of the retrieved codes. Description Column – detailed descriptions for the retrieved codes.
Diagnostics Operations Diagnosis To erase codes 1. Tap Erase Codes from the Function Menu. 2. A warning message displays to inform you of data loss when this function is applied. a) Tap Yes to continue. A confirming screen displays when the operation is successfully done. b) Tap No to exit. 3. Tap ESC on the confirming screen to exit Erase Codes. 4. Check the Read Codes function again to ensure the operation is successful. 4.6.
Diagnostics Operations Diagnosis 1. Diagnostics Toolbar Buttons – tap the drop-down button at the top center of the screen displays the toolbar buttons. See Table 4-2 Diagnostics Toolbar Buttons on page 31 for detailed descriptions of the operations for each button. 2. Main Section a) Check Box - tap the check box at the left side of the parameter name to make selection of an item. Tap the check box again to deselect the item.
Diagnostics Operations Diagnosis Waveform Graph Mode – displays the parameters in waveform graphs When displaying this mode, three control buttons will appear on the right side of the parameter item, allowing you to manipulate the display status. Text Button – resumes Text Display Mode Scale Button – changes the scale values, which are displayed below the waveform graph. There are 4 scales available: x1, x2, x4 and x8.
Diagnostics Operations 4. Diagnosis Functional Buttons The operations of all the available functional buttons on Live Data screen are described below: Back – returns you to the previous screen or exit the function. Record – starts recording the retrieved live data; the recorded data is then stored as a video clip in the Data Manager application for future reviews.
Diagnostics Operations Diagnosis Setting – tapping this button opens a setting screen, which allows you to set the trigger mode, recording duration, and various threshold values for data recording, and make other controls. Figure 4-12 Sample Setting Mode in Live Data There are 4 navigation buttons on top of the Setting mode screen. Range Button – displays the configuration screen on which you can set the threshold values, an upper limit and a lower limit, for triggering the buzzer alarm.
Diagnostics Operations Diagnosis 3. Select a parameter item on the left column, or enter the item name in the Search bar. 4. Tap on the right side of the MIN button, and enter the required minimum value. 5. Tap on the right side of the MAX button, and enter the required maximum value. 6. Tap the ON/OFF button on the right side of the Buzzer Alarm button to turn it on or off. 7. Tap Done to save the setting and return to the Live Data screen; or tap Cancel to exit without saving.
Diagnostics Operations Diagnosis 2. Tap the Record navigation button. 3. > button on the right of Trigger Type bar and select Tap the ○ the required trigger mode. 4. Tap the ○ > button on the right of Duration bar and select a length of time. 5. Tap the ○ > button on the right of Trigger Point bar and select a relative percentage of a record length to be reserved before the data recording start point. 6.
Diagnostics Operations Diagnosis Figure 4-13 Sample Active Test Screen The functional buttons at the lower right corner of the Active Test screen manipulate the test signals. The operational instructions are displayed on the main section of the test screen. Simply follow the on-screen instructions and make appropriate selections to complete the tests. Each time when an operation is successfully executed, message such as “Command Finished”, “Activation Successful”, or something similar displays.
Diagnostics Operations Service 3. The third part displays the current conditions of the vehicle control module being learned for comparison to the preconditions suggested by the second part. If the current condition of the control module is out of the suggested limit value, you must adjust the vehicle condition to meet the requirement. 4. The last part displays the instruction of how to use the functional button at the lower right corner of the screen to manipulate the teach-in operations.
Diagnostics Operations Service The most commonly performed service functions include: Oil Reset Service TPMS Programming Service EPB Service ABS/SRS Services SAS Calibration Service DPF Regeneration Service 4.7.
Diagnostics Operations Programming and Coding Steering Angle Sensor (SAS) Service This service function allow you to perform calibration for the Steering Angle Sensor, which permanently stores the current steering wheel position as the straight-ahead position in the steering angle sensor EEPROM. On successful completion of the calibration, the steering angle sensor fault memory is automatically cleared.
Diagnostics Operations Programming and Coding A. Coding – also known as Teach-in Program, Component Adaptation or something similar, is used to reprogram adaptive data for vehicle control modules after repairs or replacements of vehicle parts. B.
Diagnostics Operations Programming and Coding The main section of the Variant Coding screen displays a list of vehicle components and the coding information which mainly consists of three parts: 1. The top line on the list displays the instruction of how to use the functional button at the lower right corner of the screen to manipulate the coding operations. 2.
Diagnostics Operations Generic OBD II Operations The main section of the reprogramming interface provides you certain hardware version, and current software versions’ information, as well as the information of the newest software versions to be programmed to the control units. Throughout the programming procedure, a series of on-screen operational instructions will display to guide you through. Carefully read the on-screen information and follow the instruction to execute the programming procedure.
Diagnostics Operations Generic OBD II Operations Functions of the diagnostics toolbar buttons at the top the screen are the same as those available for specific vehicle diagnostics. See Table 4-2 Diagnostics Toolbar Buttons on page 31 for details. 4.9.1 General Procedure To access the OBD II/EOBD diagnostics functions 1. Tap the Diagnostics application button from the MaxiSys Job Menu. The Vehicle Menu displays. 2. Tap the EOBD button.
Diagnostics Operations Generic OBD II Operations NOTE: The ○ i button displayed beside the function name is tappable, tapping which opens a bubble with additional function information. 4. Select a function option to continue. DTC & FFD I/M Readiness Live Data O2 Sensor Monitor On-Board Monitor Component Test Vehicle Information Vehicle Status NOTE: Some functions are supported only on certain vehicle makes. 4.9.
Diagnostics Operations Generic OBD II Operations Figure 4-18 Sample DTC & FFD Screen Stored Codes Stored codes are the current emission related DTCs from the ECM of the vehicle. OBD II/EOBD Codes have a priority according to their emission severity, with higher priority codes overwriting lower priority codes. The priority of the code determines the illumination of the MIL and the codes erase procedure. Manufacturers rank codes differently, so expect to see differences between makes.
Diagnostics Operations Generic OBD II Operations Freeze Frame In most cases the stored frame is the last DTC that occurred. Certain DTCs, those that have a greater impact on vehicle emission, have a higher priority. In these cases, the highest priority DTC is the one for which the freeze frame records are retained. Freeze frame data includes a “snapshot” of critical parameter values at the time the DTC is set.
Diagnostics Operations Exiting Diagnostics O2 Sensor Monitor This option allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer. The O2 Sensor Monitor test function is not supported by vehicles which communicate using a controller area network (CAN). For O2 Sensor Monitor tests results of CAN-equipped vehicles, refer to On-Board Monitor. On-Board Monitor This option allows you to view the results of On-Board Monitor tests.
Diagnostics Operations Exiting Diagnostics To exit the Diagnostics application 1. From an active diagnostic screen, tap the Back or ESC functional button to exit a diagnostic session step-by-step; Or 2. Tap the Vehicle Swap button on the diagnostics toolbar to return to the Vehicle Menu screen. 3. From the vehicle menu screen, tap the Home button on the top toolbar; or tap the Back button on the navigation bar at the bottom of the screen. Or 4.
Chapter 5 Data Manager Operations The Data Manager application is used to store, print, and review the saved files. Most operations are controlled through the toolbar. Selecting the Data Manager application opens the file system menu. Different file types are sorted separately under different options, there are six types of information files to be viewed or played back. Figure 5-1 Sample Data Manager Main Screen 5.
Data Manager Operations Operations Figure 5-2 Sample Image Database Screen 1. Toolbar Buttons – used to edit, print and delete the image files. See Table 5-1 Toolbar Buttons in JPG Database on page 62 for detailed information. 2. Main Section – displays the stored images. Table 5-1 Toolbar Buttons in JPG Database Name Button Description Back Returns to the previous screen. Enter Edit Touching this button shows the editing toolbar to print, delete or view image information.
Data Manager Operations Operations To edit image information 1. Select Data Manager application from the MaxiSys Job Menu. 2. Select Image to access the JPG database. 3. Select an image to display it in full screen. 4. Tapping the screen once displays the editing toolbar. 5. Tap the Info button to open a window displaying the image information. 6. Tap the Edit button on the top right corner of the window. The editing screen displays. 7.
Data Manager Operations Operations 5.1.3 Review Data The Review Data section allows you to playback the recorded data frames of live data streams. On the Review Data main screen, select a record file to playback. Figure 5-3 Sample Data Playback Screen 1. Drop-down Toolbar – tap the button at the top center of the screen to open the Drop-down Toolbar 2. Main Section – displays the recorded data frames 3.
Data Manager Operations Operations 5.1.5 Data Logging The Data Logging section allows you to launch Support platform directly to view all records of all sent or unsent (saved) data loggings on the diagnostic system. For more details, please refer to12.5 Data Logging on Page 101 .
Chapter 6 MaxiFix Operations The MaxiFix application launches the on-line troubleshooter database, which not only provides you virtually all common diagnostic trouble code (DTC) database for most vehicles, but also serves as a forum allowing you to network with other MaxiSys users, and gives you access to a vast database of repair and diagnostic tips along with proven filed fixes.
MaxiFix Operations Navigation The MaxiFix screen layout consists of 3 main areas: 1. The Header –the tool bar across the top of the screen which allows you to select vehicles and perform searches. 2. The Main Screen –located at the center of the screen displaying content based on the vehicle attributes and keywords specified. The tabs on the main screen vary in accordance with the section selected on the Navigation Menu, allowing you to switch between functions. 3.
MaxiFix Operations Navigation 5. Select the submodel of the vehicle from the list. 6. Select the engine of the vehicle from the list. After completing the vehicle selection procedure, the identified vehicle is shown on the Header. 6.1.1 Terminology MaxiFix Tip A MaxiFix Tip provides practical information of real fix of a specific vehicle repair issue with detailed descriptions.
MaxiFix Operations Operations a) OBDII Fault Codes description and reference—helps in diagnostic assessment by making clear the nature of an automotive problem so that beginner and advanced technicians can make effective repairs b) Real Fix Tips—provides repair tips from actual shop practices and are presented in an easy to understand Complaint, Cause, Correction format.
MaxiFix Operations Operations My Messages – shows a list of message notifications which is relevant to your activities in the Question section. Support – opens the FAQ page, or a message box for contacting Customer Service by email. 6.2.1 Home Home is the first option on the Navigation Menu at the bottom of the screen. Tapping it opens your MaxiFix home page.
MaxiFix Operations Operations To ask a MaxiFix Question 1. If not already done, click Select Vehicle on the Header to specify the vehicle you are asking about. 2. Click Ask on the Navigation Menu at the bottom of the screen to open the Ask page. 3. On the Ask page find Ask for Help, fill in the following sections to ask a question. The Ask page has 4 sections: Subject – this is where you enter a brief subject for the question.
MaxiFix Operations Operations Marked Posts – opens a list with links to Tips and discussions that you are actively participating in. My Profile –allows you to view your Autel account information including: your Autel ID, personal information, MaxiFix score, phone number and register time, and edit your portrait. Vehicle Preference –used to set up a list of preferred vehicles.
MaxiFix Operations Operations View Profile Information You can view your personal profile by clicking on your account ID or “My Profile” in My MaxiFix section or edit portrait where applicable, and visit other community members’ profile by clicking their portrait. Information included in your profile determines how you are presented to the community, and what type of information will be sent to you from the community. 6.2.
MaxiFix Operations Operations Close a Question When a repair question that you've posted to the community is resolved, you are encouraged to write down the case as a way to share a good solution. This will help the other MaxiFix members to find useful information for practical fix. To close a question, you need to select the question’s response message from the message list on “My Messages” page first, then tap “Adopted Answer” and select “Close Question”.
Chapter 7 Settings Operations Selecting Settings application opens a setup interface, on which you can adjust default setting and view information about the MaxiSys system. There are eight options available for the MaxiSys system settings: Unit Language Printing Setting Wired Network Notification Center Multitask About System Settings 7.1 Operations This section describes the operation procedures for the settings. 7.1.
Settings Operations Operations 7.1.2 Language This option allows you to adjust the display language for the MaxiSys system. To adjust the language setting 1. Tap the Settings application on the MaxiSys Job Menu. 2. Tap the Language option on the left column. 3. Select the required language. A tick icon will display to the right of the selected language. 4. Tap the Home button on the top left corner to return to the MaxiSys Job Menu. Or select another setting option for the system setup. 7.1.
Settings Operations Operations To operate Ethernet configuration 1. Tap the Settings application on the MaxiSys Job Menu. 2. Tap the Wired Network option on the left column. 3. Tap the ON/OFF button to enable the Wired Network connection. If the connectivity is enabled the button turns blue, or if disabled the button turns gray. 4. Tap the ○ > button to the right of the Ethernet Configuration option, a setup window displays. 5. Select a connection type: 6.
Settings Operations Operations 3. Tap the ON/OFF button to enable or disable the Notifications function. If the function is enabled the button turns blue, or if disabled the button turns gray. 4. Tap the Home button on the top left corner to return to the MaxiSys Job Menu. Or select another setting option for the system setup. When the Notification Center function is turned on, and new messages are received by the MaxiSys device, a notification message displays on the MaxiSys Job Menu.
Settings Operations Operations 2. Tap the About option on the left column. The product information screen displays on the right. 3. Tap the Home button on the top left corner to return to the MaxiSys Job Menu, or select another setting option for the system setup, after viewing. 7.1.
Chapter 8 Shop Manager Operations The Shop Manager application helps you to manage the workshop information, customer information records, and keep test vehicle history records, which can be a great assist in dealing with daily workshop business and improves customer service.
Shop Manager Operations Name Button Vehicle History Description History Notes Touching this button opens a note form, which allows you to create audio record, attach picture or video, or edit text notes, etc. Vehicle History Touching this button opens the Vehicle History screen which displays the correlated test vehicle records. Done Saves the file when complete editing. 8.
Shop Manager Operations Vehicle History To activate a test session for the recorded vehicle 1. Tap the Shop Manager application on the MaxiSys Job Menu. 2. Select Vehicle History 3. Tap the Diagnostics button at the bottom of the thumbnail of a vehicle record item. Or, 4. Select a vehicle record item by tapping the thumbnail. 5. A Historical Test record sheet displays, check the recorded information of the recorded test vehicle, and tap the Diagnostics button on the upper right corner. 6.
Shop Manager Operations Workshop Information To edit the Historical Test record sheet 1. Tap the Shop Manager application on the MaxiSys Job Menu. 2. Select Vehicle History. 3. Select the specific vehicle history record thumbnail from the main section. The Historical Test record sheet displays. 4. Tap the Edit button to start editing. 5. Tap on each item to input the corresponding information or add attaching files or images.
Shop Manager Operations Customer Manager Figure 8-3 Sample Workshop Information Sheet 8.3 To edit the Workshop Information sheet 1. Tap the Shop Manager application on the MaxiSys Job Menu. 2. Select Workshop Information. 3. Tap the Edit button on the top toolbar. 4. Tap on each field to input the appropriate information. 5. Tap Done to save the updated workshop information sheet, or tap Cancel to exit without saving.
Shop Manager Operations 4. Customer Manager Tap the □ + photo frame beside the Name chart to add a photo. A sub menu displays, select Take Photo to take a new photo for the account, or select Choose Photo to choose from the existing files. 5. Some customers may have more than one vehicle for service; you can always add new vehicle information to the account to be correlated. Tap Add New Vehicle Information, and then fill in the vehicle information. Tap the ○ x button to cancel adding. 6.
Shop Manager Operations Customer Manager 8.3.1 History Notes The History Notes function allows you to add audio and video records, text notes and photos, to keep multi-media work logs for the associated customer account, which can be very helpful when dealing with repeat customers. Keeping notes for each vehicle serviced for each customer will keep you always on track and well organized in business. To access History Notes 1. Tap the Shop Manager application on the MaxiSys Job Menu. 2.
Shop Manager Operations Customer Manager Table 8-2 Function Buttons in History Notes Name Button Description Back Returns to the previous screen. Delete Touching this button deletes the selected note. Search Quickly locates the required note by entering the note title. Cancel Touching this button to cancel edit or file search. Edit Touching this button opens an edit window allowing you to edit notes and attach files. Add Notes Touching this button to add new note in History Notes.
Chapter 9 Update Operations The internal programming of the MaxiSys Diagnostic System, known as the firmware, can be updated using the Update application. Firmware updates increase the MaxiSys applications’ capabilities, typically by adding new tests, new models, or enhanced applications to the database. The display device automatically searches for available updates for all of the Maxisys components when it is connected to the internet.
Update Operations 3. Operations Main Section Left Column – displays vehicle logos and update firmware version information; tap the About button displays a function list in PDF showing more details about the firmware Middle Column – displays a brief introduction about the new changes to the firmware operation or capabilities. Tap ○ i button to open an information screen to view more details, and tap the dim area around to close the window.
Chapter 10 VCI Manager Operations This application allows you to pair up the MaxiSys Display Tablet with the VCI device, either the J2534 Programming Device or the Wireless Diagnostic Interface, and to check the communication status. Figure 10-1 Sample VCI Manager Screen 1. Connection Mode – there are three connection modes available for selection. The connection state is displayed alongside.
VCI Manager Operations BT Pairing 10.1 BT Pairing The VCI device needs to be either connected to a vehicle or to an available power source, so that it is powered up during the synchronization procedure. Make sure the MaxiSys Display Tablet has a charged battery or is connected to an AC/DC power supply. To pair the VCI device with the Display Tablet 1. Power on the MaxiSys Display Tablet. 2. Connect the 26-pin end of the data cable to the J2534 ECU Programming Device’s vehicle data connector. 3.
VCI Manager Operations Wired Network Connection 10.2 Wired Network Connection The Wired Network is applied for connecting the MaxiSys Display Tablet with J2534 ECU Programming Device or to an existing LAN. This section describes connecting the display tablet with the J2534 ECU Programming Device through the Ethernet cable. The J2534 ECU Programming Device needs to be either connected to a vehicle or to an AC/DC power source, so that it is powered up when communicating with the display tablet.
VCI Manager Operations Update When the wired network is successful connected, the connection status is displayed as Connected, and the two status lights at the corners alongside the Ethernet Ports on the display tablet illuminate. The solid amber light indicates steady connection, and the flashing green light indicates active communication, between the units.
Chapter 11 Remote Desk Operations The Remote Desk application launches the TeamViewer Quick Support program, which is a simple, fast and secure remote control interface. You can use the application to receive ad-hoc remote support from Autel’s support centre, colleagues, or friends, by allowing them to control your MaxiSys tablet on their PC via the TeamViewer software. 11.
Remote Desk Operations Operations To receive remote support from a partner 1. Power on the MaxiSys Display Tablet. 2. Tap the Remote Desk application on the MaxiSys Job Menu. The TeamViewer interface displays and the device ID is generated and shown. 3. Your partner must install the Remote Control software to his/her computer by downloading the TeamViewer full version program online (http://www.teamviewer.
Chapter 12 Support Operations This application launches the Support platform which synchronizes Autel’s on-line service base station with the MaxiSys display tablet. In order to synchronize the device to your on-line account, you need to register the product through the Internet when you use it for the first time.
Support Operations Support Screen Layout 12.2 Support Screen Layout The Support application interface is navigated by 4 simple buttons on the top navigation bar, operation of each is described below in turn from left to right: Home Button – returns to the MaxiSys Job Menu. Back – returns to the previous screen, each press takes you one step backwards. Forward – each press moves forward one screen until you’ve reached the last screen visited. Refresh – reload and update the screen.
Support Operations My Account 12.3 My Account The My Account screen displays the comprehensive information of the user and the product, which is synchronized with the on-line registered account, including User Info, Device Info, Update Info and Service Info. Personal Info The User Info and Device Info are both included under the Personal Info section.
Support Operations User Complaint Screen Layout Figure 12-2 Sample Complaint Screen The User Complaint screen consists of two parts. 1. 2. Option Bar Period Filter – displays only the complaint records within the defined period on the list Status Filter – displays the corresponding complaint records according to the selected case status New Complaint Button – starts a new complaint case.
Support Operations User Complaint Waiting Customer Reply – indicates the complaint has been replied by the service personnel, and requires feedback from the customer Closed – indicates the complaint case has been processed, solved, and ended To view the detailed complaint session, tap the ○ > button on the right side of the case item. To establish a new complaint session 1. Register the product online. 2. Tap the Support application on the MaxiSys Job Menu.
Support Operations Data Logging 3. Tap Complaint on the Main Menu. 4. Select an existing complaint case item on the record list by tapping the ○ > button on its right side. The screen displays the complaint session details. 5. Tap the Post Reply button on the upper right side after viewing, to make a reply. An edit screen displays. 6. Input the content in the input field, and if necessary, upload an attaching file. 7. Tap Submit to post the reply. 8.
Support Operations Communities To make a reply in a Data Logging session 1. Tap on the Sent tag to view a list of submitted data loggings. 2. Select a specific item to view the latest update of the processing progress. 3. Tap on the input field at the bottom of the screen, and enter the texts. Or tap the Audio button to record a voice message, or camera button to take a picture. 4. Tap Send to deliver your message to the technical center. 12.
Support Operations Communities 2. Select a desired group according to the subject you are about to discuss. For example, if you are going to ask a question about the MaxiSys tablet, tap MaxiSys to start a discussion. 3. Enter your topic and the discussion content in the appropriate input field. 4. Select a category or edit tags for the discussed post. This will help other members with similar interest to find your post. 5. Tap OK to submit the post. To join and reply to a discussion post 1.
Support Operations Training Channels Figure 12-5 Sample User Profile Screen Profile – displays the user’s personal information and member status. The Related links allow you to check the Top Users (ranked according to their points and levels) in the communities, as well as to find out other online users. Avatar – allows you to select an image to set as your personal Avatar to be displayed in the communities. Stuff – displays all the discussions you’ve posted at various forums in a list. 12.
Support Operations FAQ Database 12.8 FAQ Database The FAQ section provides you comprehensive and abundant references for all kinds of questions frequently asked and answered about the use of Autel’s online member account, and shopping and payment procedures. Account – displays questions and answers about the use of Autel’s online user account. Shopping & Payment – displays questions and answers about online product purchase and payment methods or procedures.
Chapter 13 Training Operations The Training application provides and allows you to play various tutorial videos stored on the device. The stored training materials mainly consists of product usage tutorials and vehicle diagnostic training videos, all produced by top-notch technicians and product experts. The application also allows you to download or watch more associated videos online, by providing quick links to Autel’s online video database. Figure 13-1 Sample Training Application Screen 1.
Training Operations Operations 2. Main Section – displays the available video files for watching To play a video 1. Tap the Support application on the MaxiSys Job Menu. The Training application screen displays. 2. Select a video file from the main section. 3. Tap the Play button on the left side. 4. Select a Player from the popup window if necessary. Now you can watch the video, it is played in full screen mode.
Chapter 14 Quick Link Operations The Quick Link application provides you with convenient access to Autel’s official website and many other well-known sites in automotive service, which offers you abundant information and resources, such as technical help, knowledge base, forums, training, and expertise consultations, etc. Figure 14-1 Sample Quick Link Screen To open a quick link 1. Tap the Quick Link application on the MaxiSys Job Menu. The Quick Link application screen displays. 2.
Chapter 15 Oscilloscope Operations The Oscilloscope application configures the MaxiSys Diagnostic Device to operate as an automotive oscilloscope when work in combination with the MaxiScope module. This function provides all the features needed for performing electrical and electronic circuit tests as well as monitoring signal activities on any modern vehicles, which shows you what is really going on with a vehicle’s electrical system. 15.
Oscilloscope Operations Safety Information WARNING: C. Applying a voltage to the ground input is likely to cause permanent damage to the oscilloscope, the attached computer, and other equipment. To prevent measurement errors caused by poor grounding, always use the high-quality USB cable supplied with the oscilloscope. External connections DANGER: D. To prevent injury or death, use only the power cord and adaptor supplied with the product.
Oscilloscope Operations Glossary 15.2 Glossary AC/DC Control Each channel can be set to either AC coupling or DC coupling. With DC coupling, the voltage displayed onscreen is equal to the true voltage of the signal with respect to ground. With AC coupling, any DC component of the signal is filtered out, leaving only the variations in the signal for the AC component.
Oscilloscope Operations Glossary Time Base The time base controls the time interval across the scope display. Voltage Range The voltage range is the range between the maximum and minimum voltages that can be accurately captured by the oscilloscope. Sinusoidal Waveform This term describes the waveform characteristics typically found in circuits with large inductance and capacitance, and often referred to as an AC signal.
Oscilloscope Operations MaxiScope Module Figure 15-2 Sample Square Waveform Peak to peak voltage This term indicates the difference in voltage between the minimum and maximum voltages occurring in the waveform. 15.3 MaxiScope Module The MaxiScope Automotive Oscilloscope tool kit is optional and available for purchase along with the MaxiSys package. There are 2 versions (basic and advanced versions) available.
Oscilloscope Operations MaxiScope Module Figure 15-3 Front, Rear, and Top View 1. USB Port Connector 2. Input Channel A/B/C/D 3. LED Indicator Light – lights up when powered on, blinks when communicating, and shimmers when error occurs 4. Warning Triangle – indicates potential safety hazard that exists on the indicated connections, and appropriate precautions should be taken. Make sure you read through the Safety Information on page 109 before using. 5.
Oscilloscope Operations MaxiScope Module Technical Specifications Main Features Description Vertical resolution 12 bits Channels 4 Bandwidth 20MHz Accuracy Voltage: 1%; Time: 50ppm Sensitivity 10mV/div to 20V/div Input Ranges (full scale) ±50mV to ±100V in 11 ranges Input Impedance 1MΩ in parallel with 22pF Input Type Single-ended, BNC connector Input Coupling Software selectable AC/DC ±200V on single input Overload Protection Maximum Sampling (Single Shot) 1 or 2 channels in use 3 or
Software Operations Screen Layout and Operations General PC Interface Description USB 2.0 – cable supplied Power Requirements Powered from USB port Compliance FCC (EMC), CE (EMC and LVD), RoHS Warranty 1 year NOTE*: Reduced to 20MS/s if channels A and B, or C and D, are enabled. 15.4 Screen Layout and Operations The Oscilloscope application works as a signal processing program that displays the shape of electrical signals onscreen with a live graph showing voltage against time.
Software Operations Screen Layout and Operations 1. Top Toolbar – used for configurations of various settings and operations of the scope 2. Functional Buttons on the top – used for configurations of channel activation, measurement scale and trigger settings 3. Measurement Grid - displays measurements of voltage against time 4. Functional Buttons at the bottom – used for configurations of trigger, time base, and measurement parameter display settings. 15.4.
Software Operations Screen Layout and Operations Reference Waveform A Reference Waveform is a copy of an existing signal waveform saved as a reference. It can be retrieved to display as a comparative reference to examine a live signal. Up to 4 reference waveforms can be saved. Figure 15-5 Ref. Waveform Save Window To create a Reference Waveform: 1. Tap the Tool button in the Top Menu. 2. Select Save Ref. in the dropdown menu. 3. Select the channel to which the desired waveform belongs. 4.
Software Operations Screen Layout and Operations Serial Decoder The Serial Decoder function is designed to decode data from a serial bus such as LIN or CAN. The decoding function can be operated on 4 channels at the same time. The decoded data parameters can be displayed either in graph or table format or both. 1. Data decoded in graph - shows the decoded data in graphic format, similar to analog waveform 2.
Oscilloscope Operations Screen Layout and Operations 15.4.2 Functional Buttons This group of buttons is used for configurations of channel activation, measurement scale and trigger settings, the operations of which are described below: Channel Control Buttons A/B/C/D - tapping each button allows you to activate or deactivate the corresponding channel; long pressing the button opens a window, which allows you to select and configure appropriate probes for specific tests.
Oscilloscope Operations Screen Layout and Operations Figure 15-7 Sample Measurement Grid Voltage per division – shown down the left side of the screen, referred to as the Y-axis Time per division – shown along the bottom of the screen, referred to as the X-axis Multiple Scope Channels The MaxiScope software features multiple channel display which enables more than one waveform to be displayed at the same time. It is useful for making comparisons among different signals.
Oscilloscope Operations Screen Layout and Operations To adjust the time base 1. Unselect the Y-axis if it’s activated. 2. Use your 2 fingers to adjust the time base with the typical zoom gestures on the measurement grid area. 15.4.4 Measurement Rulers The Measurement Rulers allow the voltage and time duration of a waveform to be measured precisely. There are 2 kinds of measurement rulers: the vertical Time Ruler and the horizontal Voltage Ruler.
Oscilloscope Operations Screen Layout and Operations 15.4.5 Functional Buttons This group of buttons includes trigger setting buttons allowing you to set trigger source and trigger mode, a Time base button for adjustment, and a Measurement button with options for various measurement types. Trigger On/Off – taps to turn on/off the trigger. The button displays as Trigger Off when it is activated, and vice versa.
Oscilloscope Operations Troubleshooting To set a specific trigger point 1. Tap the Trigger On button to activate the trigger. 2. Configures the specific trigger source, the trigger slope and the trigger mode according to the test demand. 3. Tap and slide the voltage scale reference line up or down to the desired voltage point. The voltage info is displayed in a small reference box. 4. Tap and slide the time base reference line left or right to the desired point. 5.
Digital Inspection Operations MaxiScope Firmware Update To update the Maxiscope firmware 1. Install the CD provided with the MaxiScope tool kit into the CD-ROM of the computer. The driver installation wizard will load momentarily. 2. Follow the auto run installation instructions onscreen to finish the Driver Program installation. 3. Connect the MaxiScope to the computer using the USB cable provided by the tool kit. 4. Locate and double click the MaxiScopeUpdate.
Chapter 16 Digital Inspection Operations The Digital Inspection application configures the MaxiSys Diagnostic Device to operate as a digital video scope by simply connecting the tablet to a Digital Inspection Camera. This function allows you to examine difficult-to-reach areas normally hidden from sight, with the ability to record digital still images and videos, which offers you an economical solution to inspect machinery, facilities, and infrastructure in a safe and quick way.
Digital Inspection Operations Additional Accessories 16.1 Additional Accessories The Digital Inspection Camera and its fittings are the additional accessories. Both sizes (8.5 mm and 5.5 mm) of the imager head are optional and available for purchase along with the standard MaxiSys tool kit. Digital Inspection Camera Figure 16-1 Digital Inspection Camera 1. Removable Imager Head Cable – connects to the tool when performing digital inspections for image and video viewing 2.
Digital Inspection Operations Additional Accessories Imager Head Accessorie Figure 16-2 8.5mm Imager Head Accessories 1. Magnet – picks up small metal objects, such as dropped rings or screws 2. Hook – unclogs obstacles and picks up wires in the pipes or confined areas 3. Mirror – helps to look around corners and see the unreachable areas Figure 16-3 5.5mm Imager Head Accessories 1. Mirror – helps to look around corners and see the unreachable areas 2.
Digital Inspection Operations Additional Accessories 1. Hold the accessory and the imager head. 2. Slip the end of the accessory over the imager head and then fix the accessory. For 5.5mm Imager Head The two accessories, including the Magnet and Mirror (Figure 16-3), can be attached to the Imager Head with the same manner described below: 1. Hold the accessory and the imager head.
Digital Inspection Operations 2. Operations Screw the thread part of the accessory over the imager head to fix the accessory. 16.1.1 Technical Specifications Item Optimal Distance Description Viewing 1" to 14" (2.54cm to 35.56cm) with 8.5mm diameter imager head 3/8" to 12" (0.95cm to 30cm) with 5.
Digital Inspection Operations Operations To take pictures using the Digital Inspection application 1. Connect the Imager Head Cable to the USB port on the top side of the MaxiSys Display Tablet. 2. If not already done, power up the MaxiSys Display Tablet. 3. Tap the Digital Inspection application on the MaxiSys Job Menu. The Digital Inspection application interface displays, showing a camera operating screen. The default camera is now the Imager head. 4.
Digital Inspection Operations Operations 7. Tap the red circle again to stop recording. The recorded video is automatically saved to the system Gallery. 8. Tap the thumbnail image on the top right corner to review the recorded video. 9. Tap the Play button to play the video. 10. Tap on the selected video and the edit toolbar instantly displays. 11. Tap the appropriate button to share, delete, or edit the video. 12.
Chapter 17 Maintenance and Service To ensure that the MaxiSys diagnostic tablet and the combined VCI unit perform at their optimum level, we advise that the product maintenance instructions covered in this section is read and followed. 17.1 Maintenance Instructions The following shows how to maintain your devices, together with precautions to take. Use a soft cloth and alcohol or a mild window cleaner to clean the touch screen of the tablet.
Maintenance and Service Troubleshooting Checklist 17.2 Troubleshooting Checklist A. B. When the display tablet does not work properly: Make sure the tablet has been registered online. Make sure the system software and diagnostic application software are properly updated. Make sure the tablet is connected to the Internet. Check all cables, connections, and indicators to see if the signal is being received. When battery life is shorter than usual: C.
Maintenance and Service About Battery Usage Do not use a damaged battery charger. Do not disassemble or open crush, bend or deform, puncture or shred. Do not modify or remanufacture, attempt to insert foreign objects into the battery, expose to fire, explosion or other hazard. Make sure to use the charger and USB cables only that come together in the package. If you use the other charger and USB cables, you might incur malfunction or failure of the device.
Maintenance and Service Service Procedures Call 1-855-288-3587/1-855-AUTELUS 0086-755-86147779 (China). Contact the local distributer or agent. Visit our website http://pro.autel.com or www.autel.com. (North America), or Repair Service If it becomes necessary to return your device for repair, please download the repair service form from www.autel.com, and fill in the form.
Chapter 18 Compliance Information FCC Compliance FCC ID: WQ8MAXISYSMY908 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Chapter 19 Warranty 12-Month Limited Warranty Autel Intelligent Technology Corp., Ltd.
