User Manual

ManualsBrandsAutel ManualsAutomotiveAutomotive Scan Tool with MV108, 2021 Newest Diagnostic Scanner, All System Diagnostics & 31 Services, ECU Coding, Bi-Directional Control Oil Reset, EPB, Advanced Ver. of MS906

131

132

133

134

135

136

137

138

139

140

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabilities
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Chapter 1 Using This Manual
- 1.1 Conventions
Chapter 2 General Introduction
- 2.1 MaxiSys System Display Tablet
- 2.2 VCI – Wireless Diagnostic Interface
- 2.3 Accessory Kit
  - 2.3.1 OBD I Adapters
  - 2.3.2 Other Accessories
Chapter 3 Getting Started
- 3.1 Powering Up
- 3.2 Powering Down
  - 3.2.1 Reboot System
- 3.3 Installing Computer Software
  - 3.3.1 Printing Operation
Chapter 4 Diagnostics Operations
- 4.1 Establishing Vehicle Communication
- 4.2 Getting Started
  - 4.2.1 Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3 Vehicle Identification
- 4.4 Navigation
- 4.5 Main Menu
- 4.6 Diagnosis
- 4.7 Service
  - 4.7.1 Function Descriptions
- 4.8 Generic OBD II Operations
  - 4.8.1 General Procedure
  - 4.8.2 Function Descriptions
- 4.9 Exiting Diagnostics
Chapter 5 TPMS Service Operations
- 5.1 Navigation
  - 5.1.1 TPMS Service Screen Layout
- 5.2 Check Operations
  - Main Section
- 5.3 Programming Operations
- 5.4 Relearn Operations
Chapter 6 MaxiFix Operations
- 6.1 Navigation
- 6.2 Operations
Chapter 7 Shop Manager Operations
- 7.1 Vehicle History
  - 7.1.1 Historical Test Record
- 7.2 Workshop Information
- 7.3 Customer Manager
  - 7.3.1 History Notes
Chapter 8 Data Manager Operations
- 8.1 Operations
Chapter 9 Settings Operations
- 9.1 Operations
Chapter 10 Update Operations
Chapter 11 VCI Manager Operations
- 11.1 BT Pairing
- 11.2 Update
- 11.3 TPMS Module Update
Chapter 12 Support Operations
- 12.1 Product Registration
- 12.2 Support Screen Layout
- 12.3 My Account
- 12.4 User Complaint
  - Screen Layout
- 12.5 Data Logging
- 12.6 Communities
  - User Profile
- 12.7 Training Channels
- 12.8 FAQ Database
Chapter 13 Training Operations
Chapter 14 Remote Desk Operations
- 14.1 Operations
Chapter 15 Quick Link Operations
Chapter 16 Oscilloscope Operations
- 16.1 Safety Information
- 16.2 Glossary
- 16.3 MaxiScope Module
  - Power Source
  - Technical Specifications
- 16.4 Screen Layout and Operations
- 16.5 Troubleshooting
- 16.6 MaxiScope Firmware Update
Chapter 17 Digital Inspection Operations
- 17.1 Additional Accessories
- 17.2 Operations
Chapter 18 Maintenance and Service
- 18.1 Maintenance Instructions
- 18.2 Troubleshooting Checklist
- 18.3 About Battery Usage
- 18.4 Service Procedures
Chapter 19 Compliance Information
- FCC Compliance
- FCC ID: WQ8MAXISYSMY906TS (for MaxiSys MS906TS)
- FCC ID: WQ8MAXISYSMY906BT (for MaxiSys MS906BT)
- SAR:
Chapter 20 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

Digital Inspection Operations Additional Accessories

133

Imager Head Accessories

Figure 17-2 8.5mm Imager Head Accessories

1. Magnet – picks up small metal objects, such as dropped rings or screws

2. Hook – unclogs obstacles and picks up wires in the pipes or confined

areas

3. Mirror – helps to look around corners and see the unreachable areas

Figure 17-3 5.5mm Imager Head Accessories

1. Mirror – helps to look around corners and see the unreachable areas

2. Magnet - picks up small metal objects, such as dropped rings or screws

Accessory Assembly

For 8.5mm Imager Head

The three accessories, including the Magnet, Hook, and Mirror (Figure 17-2),

can be attached to the Imager Head with the same manner described below: