User Manual

ManualsBrandsAutel ManualsAutomotiveAutomotive Scan Tool with MV108, 2021 Newest Diagnostic Scanner, All System Diagnostics & 31 Services, ECU Coding, Bi-Directional Control Oil Reset, EPB, Advanced Ver. of MS906

111

112

113

114

115

116

117

118

119

120

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabilities
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Chapter 1 Using This Manual
- 1.1 Conventions
Chapter 2 General Introduction
- 2.1 MaxiSys System Display Tablet
- 2.2 VCI – Wireless Diagnostic Interface
- 2.3 Accessory Kit
  - 2.3.1 OBD I Adapters
  - 2.3.2 Other Accessories
Chapter 3 Getting Started
- 3.1 Powering Up
- 3.2 Powering Down
  - 3.2.1 Reboot System
- 3.3 Installing Computer Software
  - 3.3.1 Printing Operation
Chapter 4 Diagnostics Operations
- 4.1 Establishing Vehicle Communication
- 4.2 Getting Started
  - 4.2.1 Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3 Vehicle Identification
- 4.4 Navigation
- 4.5 Main Menu
- 4.6 Diagnosis
- 4.7 Service
  - 4.7.1 Function Descriptions
- 4.8 Generic OBD II Operations
  - 4.8.1 General Procedure
  - 4.8.2 Function Descriptions
- 4.9 Exiting Diagnostics
Chapter 5 TPMS Service Operations
- 5.1 Navigation
  - 5.1.1 TPMS Service Screen Layout
- 5.2 Check Operations
  - Main Section
- 5.3 Programming Operations
- 5.4 Relearn Operations
Chapter 6 MaxiFix Operations
- 6.1 Navigation
- 6.2 Operations
Chapter 7 Shop Manager Operations
- 7.1 Vehicle History
  - 7.1.1 Historical Test Record
- 7.2 Workshop Information
- 7.3 Customer Manager
  - 7.3.1 History Notes
Chapter 8 Data Manager Operations
- 8.1 Operations
Chapter 9 Settings Operations
- 9.1 Operations
Chapter 10 Update Operations
Chapter 11 VCI Manager Operations
- 11.1 BT Pairing
- 11.2 Update
- 11.3 TPMS Module Update
Chapter 12 Support Operations
- 12.1 Product Registration
- 12.2 Support Screen Layout
- 12.3 My Account
- 12.4 User Complaint
  - Screen Layout
- 12.5 Data Logging
- 12.6 Communities
  - User Profile
- 12.7 Training Channels
- 12.8 FAQ Database
Chapter 13 Training Operations
Chapter 14 Remote Desk Operations
- 14.1 Operations
Chapter 15 Quick Link Operations
Chapter 16 Oscilloscope Operations
- 16.1 Safety Information
- 16.2 Glossary
- 16.3 MaxiScope Module
  - Power Source
  - Technical Specifications
- 16.4 Screen Layout and Operations
- 16.5 Troubleshooting
- 16.6 MaxiScope Firmware Update
Chapter 17 Digital Inspection Operations
- 17.1 Additional Accessories
- 17.2 Operations
Chapter 18 Maintenance and Service
- 18.1 Maintenance Instructions
- 18.2 Troubleshooting Checklist
- 18.3 About Battery Usage
- 18.4 Service Procedures
Chapter 19 Compliance Information
- FCC Compliance
- FCC ID: WQ8MAXISYSMY906TS (for MaxiSys MS906TS)
- FCC ID: WQ8MAXISYSMY906BT (for MaxiSys MS906BT)
- SAR:
Chapter 20 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

Remote Desk Operations Operations

112

 To receive remote support from a partner

1. Power on the Display Tablet.

2. Tap the Remote Desk application on the MaxiSys Job Menu. The

TeamViewer interface displays and the device ID is generated and

shown.

3. Your partner must install the Remote Control software to his/her

computer by downloading the TeamViewer full version program

online (http://www.teamviewer.com), and then start the software on

his/her computer at the same time, in order to provide support and

take control of the Display Tablet remotely.

4. Provide your ID to the partner, and wait for him/her to send you a

remote control request.

5. A popup displays to ask for your confirmation to allow remote control

on your device.

6. Tap Allow to accept, or tap Deny to reject.

Refer to the associated TeamViewer documents for additional information.