User Manual

ManualsBrandsAutel ManualsAutomotiveMaxiSys Pro MK908P Automotive Diagnostic Tool (Same Functions as MaxiSys Elite) with WiFi Bluetooth Jbox J2534 VCI ECUs BCM PCM Reprogramming and Coding

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabilities
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Contents
Chapter 1 Using This Manual
- 1.1 Conventions
Chapter 2 General Introduction
- 2.1 MaxiSys Display Tablet
- 2.2 VCI – Wireless Diagnostic Interface
- 2.3 VCI – J2534 ECU Programming Device
- 2.4 Accessories Kit
Chapter 3 Getting Started
- 3.1 Powering Up
- 3.2 Powering Down
  - 3.2.1 Reboot System
- 3.3 Installing Computer Software
  - 3.3.1 Printing Operation
Chapter 4 Diagnostics Operations
- 4.1 Establishing Vehicle Communication
- 4.2 Getting Started
  - 4.2.1 Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3 Vehicle Identification
- 4.4 Navigation
- 4.5 Main Menu
- 4.6 Diagnosis
- 4.7 Service
  - 4.7.1 Function Descriptions
- 4.8 Programming and Coding
- 4.9 Generic OBD II Operations
  - 4.9.1 General Procedure
  - 4.9.2 Function Descriptions
- 4.10 Exiting Diagnostics
Chapter 5 Data Manager Operations
- 5.1 Operations
Chapter 6 MaxiFix Operations
- 6.1 Navigation
- 6.2 Operations
Chapter 7 Settings Operations
- 7.1 Operations
Chapter 8 Shop Manager Operations
- 8.1 Vehicle History
  - 8.1.1 Historical Test Record
- 8.2 Workshop Information
- 8.3 Customer Manager
  - 8.3.1 History Notes
Chapter 9 Update Operations
Chapter 10 VCI Manager Operations
- 10.1 BT Pairing
- 10.2 Update
Chapter 11 Remote Desk Operations
- 11.1 Operations
Chapter 12 Support Operations
- 12.1 Product Registration
- 12.2 Support Screen Layout
- 12.3 My Account
- 12.4 User Complaint
  - Screen Layout
- 12.5 Data Logging
- 12.6 Communities
  - User Profile
- 12.7 Training Channels
- 12.8 FAQ Database
Chapter 13 Training Operations
Chapter 14 Quick Link Operations
Chapter 15 MaxiScope Operations
- 15.1 Safety Information
- 15.2 Glossary
- 15.3 MaxiScope Module
- 15.4 Screen Layout and Operations
- 15.5 Troubleshooting
- 15.6 MaxiScope Firmware Update
Chapter 16 Digital Inspection Operations
- 16.1 Additional Accessories
- 16.2 Operations
Chapter 17 Maintenance and Service
- 17.1 Maintenance Instructions
- 17.2 Troubleshooting Checklist
- 17.3 About Battery Usage
- 17.4 Service Procedures
Chapter 18 Compliance Information
- FCC Compliance FCC ID: WQ8MAXISYSMY908
- SAR:
Chapter 19 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

Diagnostics Operations Diagnosis

 To erase codes

1. Tap Erase Codes from the Function Menu.

2. A warning message displays to inform you of data loss when this

function is applied.

a) Tap Yes to continue. A confirming screen displays when the

operation is successfully done.

b) Tap No to exit.

3. Tap ESC on the confirming screen to exit Erase Codes.

4. Check the Read Codes function again to ensure the operation is

successful.

4.6.4 Live Data

When this function is selected, the screen displays the data list for the

selected module. The items available for any control module vary from one

vehicle to another. The parameters display in the order that they are

transmitted by the ECM, so expect variation between vehicles.

Gesture scrolling allows you to quickly move through the data list. Simply

touch the screen and drag your finger up or down to reposition the parameters

being displayed if the data covers more than one screen. The figure below

shows a typical Live Data screen:

Figure 4-11 Sample Live Data Screen