User Manual

ManualsBrandsAutel ManualsAutomotiveMaxiSys Pro MK908P Automotive Diagnostic Tool (Same Functions as MaxiSys Elite) with WiFi Bluetooth Jbox J2534 VCI ECUs BCM PCM Reprogramming and Coding

131

132

133

134

135

136

137

138

139

140

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabilities
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Contents
Chapter 1 Using This Manual
- 1.1 Conventions
Chapter 2 General Introduction
- 2.1 MaxiSys Display Tablet
- 2.2 VCI – Wireless Diagnostic Interface
- 2.3 VCI – J2534 ECU Programming Device
- 2.4 Accessories Kit
Chapter 3 Getting Started
- 3.1 Powering Up
- 3.2 Powering Down
  - 3.2.1 Reboot System
- 3.3 Installing Computer Software
  - 3.3.1 Printing Operation
Chapter 4 Diagnostics Operations
- 4.1 Establishing Vehicle Communication
- 4.2 Getting Started
  - 4.2.1 Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3 Vehicle Identification
- 4.4 Navigation
- 4.5 Main Menu
- 4.6 Diagnosis
- 4.7 Service
  - 4.7.1 Function Descriptions
- 4.8 Programming and Coding
- 4.9 Generic OBD II Operations
  - 4.9.1 General Procedure
  - 4.9.2 Function Descriptions
- 4.10 Exiting Diagnostics
Chapter 5 Data Manager Operations
- 5.1 Operations
Chapter 6 MaxiFix Operations
- 6.1 Navigation
- 6.2 Operations
Chapter 7 Settings Operations
- 7.1 Operations
Chapter 8 Shop Manager Operations
- 8.1 Vehicle History
  - 8.1.1 Historical Test Record
- 8.2 Workshop Information
- 8.3 Customer Manager
  - 8.3.1 History Notes
Chapter 9 Update Operations
Chapter 10 VCI Manager Operations
- 10.1 BT Pairing
- 10.2 Update
Chapter 11 Remote Desk Operations
- 11.1 Operations
Chapter 12 Support Operations
- 12.1 Product Registration
- 12.2 Support Screen Layout
- 12.3 My Account
- 12.4 User Complaint
  - Screen Layout
- 12.5 Data Logging
- 12.6 Communities
  - User Profile
- 12.7 Training Channels
- 12.8 FAQ Database
Chapter 13 Training Operations
Chapter 14 Quick Link Operations
Chapter 15 MaxiScope Operations
- 15.1 Safety Information
- 15.2 Glossary
- 15.3 MaxiScope Module
- 15.4 Screen Layout and Operations
- 15.5 Troubleshooting
- 15.6 MaxiScope Firmware Update
Chapter 16 Digital Inspection Operations
- 16.1 Additional Accessories
- 16.2 Operations
Chapter 17 Maintenance and Service
- 17.1 Maintenance Instructions
- 17.2 Troubleshooting Checklist
- 17.3 About Battery Usage
- 17.4 Service Procedures
Chapter 18 Compliance Information
- FCC Compliance FCC ID: WQ8MAXISYSMY908
- SAR:
Chapter 19 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

Digital Inspection Operations Additional Accessories

125

1. Hold the accessory and the imager head.

2. Slip the end of the accessory over the imager head and then fix the

accessory.

For 5.5mm Imager Head

The two accessories, including the Magnet and Mirror (Figure 16-3), can be

attached to the Imager Head with the same manner described below:

1. Hold the accessory and the imager head.