User Manual

ManualsBrandsAutel ManualsAutomotiveMaxiCOM MK908 Automotive Scan Tool 2021 Newest OE-Level All Systems Diagnosis, Bi-Directional Control, ECU Coding, 31+ Services, ABS Brake Bleeding, Oil Reset, Upgraded of MS906BT

121

122

123

124

125

126

127

128

129

130

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabili
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Chapter 1 Using This Manual
- 1.1Conventions
Chapter 2 General Introduction
- 2.1MaxiCOM Display Tablet
- 2.2VCI – Wireless Diagnostic Interface
- 2.3VCI – J2534 ECU Programming Device
- 2.4Accessories Kit
Chapter 3 Getting Started
- 3.1Powering Up
- 3.2Powering Down
  - 3.2.1Reboot System
- 3.3Installing Computer Software
  - 3.3.1Printing Operation
Chapter 4 Diagnostics Operations
- 4.1Establishing Vehicle Communication
- 4.2Getting Started
  - 4.2.1Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3Vehicle Identification
- 4.4Navigation
- 4.5Main Menu
- 4.6Diagnosis
- 4.7Service
  - 4.7.1Function Descriptions
- 4.8Coding
  - Variant Coding
- 4.9Generic OBD II Operations
  - 4.9.1General Procedure
  - 4.9.2Function Descriptions
- 4.10Exiting Diagnostics
Chapter 5 Data Manager Operations
- 5.1Operations
Chapter 6 ADAS
Chapter 7 MaxiFix Operations
- 7.1Navigation
- 7.2Operations
Chapter 8 Settings Operations
- 8.1Operations
Chapter 9 Shop Manager Operations
- 9.1Vehicle History
  - 9.1.1Historical Test Record
- 9.2Workshop Information
- 9.3Customer Manager
  - 9.3.1History Notes
Chapter 10 Update Operations
Chapter 11 VCI Manager Operations
- 11.1BT Pairing
- 11.2Update
Chapter 12 Remote Desk Operations
- 12.1Operations
Chapter 13 Support
Chapter 14 Academy
Chapter 15 Quick Link Operations
Chapter 16 MaxiScope Operations
- 16.1Safety Information
- 16.2Glossary
- 16.3MaxiScope Module
- 16.4Screen Layout and Operations
- 16.5Troubleshooting
- 16.6MaxiScope Firmware Update
Chapter 17 Function Viewer
Chapter 18 Digital Inspection Operations
- 18.1Additional Accessories
- 18.2Operations
Chapter 19 Maintenance and Service
- 19.1Maintenance Instructions
- 19.2Troubleshooting Checklist
- 19.3About Battery Usage
- 19.4Service Procedures
Chapter 20 Compliance Information
- FCC Compliance FCC ID: WQ8MAXI
- SAR:
Chapter 21 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

123

2. Screw the thread part of the accessory over the imager head to fix the

accessory.

18.1.1 Technical Specifications

Item

Description

Optimal Viewing

Distance

1" to 14" (2.54cm to 35.56cm) with 8.5mm

diameter imager head

3/8" to 12" (0.95cm to 30cm) with 5.5mm

diameter imager head

Image Capture

JPG images (640x480) AVI videos (320 x 240)

Operating Temperature

Main Unit: 0°C to 55°C (ambient)

Cable: -10°C to 70°C

Storage Temperature

-20°C to 75°C (ambient)

Waterproof

Imager head and cable to 1m

Weigh

0.3 kg with 8.5mm diameter imager head

0.2 kg with 5.5mm diameter imager head

18.2 Operations

Before performing the Digital Inspection application, the Imager Head Cable

must be connected to the MaxiCOM display tablet through the USB port.

Install the correct imager head accessories for use in the appropriate

application.

NOTE: When in operation, the imager head cable can be bent into a certain