User Manual

ManualsBrandsAutel ManualsAutomotiveMaxiCOM MK908 Automotive Scan Tool 2021 Newest OE-Level All Systems Diagnosis, Bi-Directional Control, ECU Coding, 31+ Services, ABS Brake Bleeding, Oil Reset, Upgraded of MS906BT

111

112

113

114

115

116

117

118

119

120

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabili
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Chapter 1 Using This Manual
- 1.1Conventions
Chapter 2 General Introduction
- 2.1MaxiCOM Display Tablet
- 2.2VCI – Wireless Diagnostic Interface
- 2.3VCI – J2534 ECU Programming Device
- 2.4Accessories Kit
Chapter 3 Getting Started
- 3.1Powering Up
- 3.2Powering Down
  - 3.2.1Reboot System
- 3.3Installing Computer Software
  - 3.3.1Printing Operation
Chapter 4 Diagnostics Operations
- 4.1Establishing Vehicle Communication
- 4.2Getting Started
  - 4.2.1Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3Vehicle Identification
- 4.4Navigation
- 4.5Main Menu
- 4.6Diagnosis
- 4.7Service
  - 4.7.1Function Descriptions
- 4.8Coding
  - Variant Coding
- 4.9Generic OBD II Operations
  - 4.9.1General Procedure
  - 4.9.2Function Descriptions
- 4.10Exiting Diagnostics
Chapter 5 Data Manager Operations
- 5.1Operations
Chapter 6 ADAS
Chapter 7 MaxiFix Operations
- 7.1Navigation
- 7.2Operations
Chapter 8 Settings Operations
- 8.1Operations
Chapter 9 Shop Manager Operations
- 9.1Vehicle History
  - 9.1.1Historical Test Record
- 9.2Workshop Information
- 9.3Customer Manager
  - 9.3.1History Notes
Chapter 10 Update Operations
Chapter 11 VCI Manager Operations
- 11.1BT Pairing
- 11.2Update
Chapter 12 Remote Desk Operations
- 12.1Operations
Chapter 13 Support
Chapter 14 Academy
Chapter 15 Quick Link Operations
Chapter 16 MaxiScope Operations
- 16.1Safety Information
- 16.2Glossary
- 16.3MaxiScope Module
- 16.4Screen Layout and Operations
- 16.5Troubleshooting
- 16.6MaxiScope Firmware Update
Chapter 17 Function Viewer
Chapter 18 Digital Inspection Operations
- 18.1Additional Accessories
- 18.2Operations
Chapter 19 Maintenance and Service
- 19.1Maintenance Instructions
- 19.2Troubleshooting Checklist
- 19.3About Battery Usage
- 19.4Service Procedures
Chapter 20 Compliance Information
- FCC Compliance FCC ID: WQ8MAXI
- SAR:
Chapter 21 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

104

Frequency

This term describes the number of signal occurrences per second. Frequency is

measured in Hz (hertz).

Square Waveform

This term describes the waveform characteristics normally generated by signals

switching between clearly defined voltage levels, such as a Hal effect sensor signal

may create by switching a voltage to ground. A typical digital square waveform is shown

below:

Peak to peak voltage

This term indicates the difference in voltage between the minimum and maximum

voltages occurring in the waveform.

16.3 MaxiScope Module

The MaxiScope Automotive Oscilloscope tool kit is optional and available for

purchase along with the MaxiCOM package. There are 2 versions (basic and

advanced versions) available.

The MaxiScope tool kit comes standard with:



MaxiScope Module



USB Cable

Figure 16- 2 Sample Square Waveform