User Manual

ManualsBrandsAutel ManualsAutomotiveMaxiCOM MK808BT Car Diagnostic Scan Tool, 2021 Newest Upgraded Ver. of MK808, MX808, All Systems Diagnosis & 25+ Services, ABS Bleed, Oil Reset, EPB, SAS, DPF, BMS, Throttle, Injector Coding

100

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabili
For Services and Support
Safety Information
Safety Messages
Safety Instructions
- DANGER
- SAFETY WARNINGS
CONTENTS
1Using This Manual
- Conventions
2General Introduction
- MaxiCOM MK808BT Display Tablet
- VCI – Vehicle Communication Interface
- Other Accessories
3Getting Started
- NOTE
- Powering Up
- Powering Down
  - To power down the tablet
4Diagnostics
- Establishing Vehicle Communication
- Getting Started
  - Vehicle Menu Layout
  - Top Toolbar Buttons
    - Vehicle Manufacturer Buttons
- Vehicle Identification
- Navigation
- Diagnosis
  - Auto Scan
  - Control Units
- Generic OBD II Operations
  - General Procedure
  - Function Descriptions
- Exiting Diagnostics
  - To exit the Diagnostics application
5Service
- Oil Reset Service
  - To perform oil reset functions
- Electronic Parking Brake (EPB) Service
  - EPB Safety
    - To perform EPB functions
  - Parking brake: Initial operation
    - Figure 5- 7 Sample Parking brake: Initial operatio
    - Figure 5- 8 Sample Parking brake: Initial operatio
- Battery Management System (BMS) Service
  - Register Battery Replacement
    - To register the battery exchange
- Steering Angle Sensor (SAS) Service
  - Steering Angle Sensor adjustment
    - Figure 5-23 Sample SAS Function Screen 8
- Diesel Particle Filter (DPF) Service
  - Diesel particulate filter：-Request regeneration
6Data Manager
- Operations
7Settings
- Unit
- To adjust the unit setting
- Language
  - To adjust the language setting
- Printing Setting
  - To setup the printer connection
  - Printing via PC
    - To install the printer driver program to a compute
    - To perform printing through the computer
- Notification Center
  - To enable the Notification Center function
- Auto Update
  - To set auto system or vehicle update
- System Settings
  - To enable the App Switcher function
- About
  - To check the MaxiCOM product information in About
8Update
- Tablet Update
  - Software Update
  - Firmware Update
- MaxiVCI Mini Update
  - Update via Display Tablet
    - To update the MaxiVCI Mini software
  - Update via PC
9VCI Manager
- BT Pairing
  - To pair the MaxiVCI Mini with the Tablet
- Update
- Programmer Update
10Shop Manager
- Vehicle History
- To activate a test session for the recorded vehicl
- To edit the Historical Test record sheet
- Workshop Information
  - To edit the Workshop Information sheet
- Customer Manager
11Academy
12Remote Desk
- To receive remote support from a partner
13MaxiFix
- Navigation
- Operations
14Support
- Product Registration
  - To register the diagnostic device
- Support Screen Layout
- My Account
- User Complaint
  - To establish a new complaint session
  - To make a reply in a complaint session
- Data Logging
  - To make a reply in a Data Logging session
- Communities
  - To start a discussion
  - To join and reply to a discussion post
- Training Channels
- FAQ Database
15Quick Link
- To open a quick link
16Function Viewer
- To Search by the vehicle
- Search by the functions
17Maintenance and Service
- Maintenance Instructions
- Troubleshooting Checklist
- About Battery Usage
- Service Procedures
18Compliance Information
- FCC ComplianceFCC ID: WQ81806-808BT
- SAR
- RF WARNING STATEMENT
- RoHS COMPLIANCE
- CE COMPLIANCE
19Warranty
- Limited One Year Warranty
  - This warranty does not apply to:
    - IMPORTANT

9 VCI Manager

This application pairs the tablet with the MaxiVCI Mini, checks the

communication status and update the VCI software.

Figure 9- 1 Sample VCI Manager Screen

1. Connection Mode – there are three connection modes available for

selection. The connection state is displayed alongside.

 BT Paring – when paired to a wireless device, the connection state

displays as Paired; otherwise it displays as Unpaired.

 Update (for VCI software only) – when the MaxiCOM tablet and the

MaxiVCI Mini are connected by a USB cable, this function is

used to update VCI software via Internet.

2. BT Setting

The BT Setting screen displays the types and product serial numbers

for all the devices available for pairing. Tap a required device to start

pairing. The BT status icon displayed to the left of the device name

indicates the received signal strength.

BT Pairing

The MaxiVCI Mini needs to be connected to a vehicle, so that it is

powered during the synchronization procedure. Ensure the tablet has

sufficient battery life or is connected to an external power supply.