User Manual

ManualsBrandsAutel ManualsAutomotiveMaxiCOM MK808BT Car Diagnostic Scan Tool, 2021 Newest Upgraded Ver. of MK808, MX808, All Systems Diagnosis & 25+ Services, ABS Bleed, Oil Reset, EPB, SAS, DPF, BMS, Throttle, Injector Coding

135

136

137

138

139

140

141

142

143

144

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabili
For Services and Support
Safety Information
Safety Messages
Safety Instructions
- DANGER
- SAFETY WARNINGS
CONTENTS
1Using This Manual
- Conventions
2General Introduction
- MaxiCOM MK808BT Display Tablet
- VCI – Vehicle Communication Interface
- Other Accessories
3Getting Started
- NOTE
- Powering Up
- Powering Down
  - To power down the tablet
4Diagnostics
- Establishing Vehicle Communication
- Getting Started
  - Vehicle Menu Layout
  - Top Toolbar Buttons
    - Vehicle Manufacturer Buttons
- Vehicle Identification
- Navigation
- Diagnosis
  - Auto Scan
  - Control Units
- Generic OBD II Operations
  - General Procedure
  - Function Descriptions
- Exiting Diagnostics
  - To exit the Diagnostics application
5Service
- Oil Reset Service
  - To perform oil reset functions
- Electronic Parking Brake (EPB) Service
  - EPB Safety
    - To perform EPB functions
  - Parking brake: Initial operation
    - Figure 5- 7 Sample Parking brake: Initial operatio
    - Figure 5- 8 Sample Parking brake: Initial operatio
- Battery Management System (BMS) Service
  - Register Battery Replacement
    - To register the battery exchange
- Steering Angle Sensor (SAS) Service
  - Steering Angle Sensor adjustment
    - Figure 5-23 Sample SAS Function Screen 8
- Diesel Particle Filter (DPF) Service
  - Diesel particulate filter：-Request regeneration
6Data Manager
- Operations
7Settings
- Unit
- To adjust the unit setting
- Language
  - To adjust the language setting
- Printing Setting
  - To setup the printer connection
  - Printing via PC
    - To install the printer driver program to a compute
    - To perform printing through the computer
- Notification Center
  - To enable the Notification Center function
- Auto Update
  - To set auto system or vehicle update
- System Settings
  - To enable the App Switcher function
- About
  - To check the MaxiCOM product information in About
8Update
- Tablet Update
  - Software Update
  - Firmware Update
- MaxiVCI Mini Update
  - Update via Display Tablet
    - To update the MaxiVCI Mini software
  - Update via PC
9VCI Manager
- BT Pairing
  - To pair the MaxiVCI Mini with the Tablet
- Update
- Programmer Update
10Shop Manager
- Vehicle History
- To activate a test session for the recorded vehicl
- To edit the Historical Test record sheet
- Workshop Information
  - To edit the Workshop Information sheet
- Customer Manager
11Academy
12Remote Desk
- To receive remote support from a partner
13MaxiFix
- Navigation
- Operations
14Support
- Product Registration
  - To register the diagnostic device
- Support Screen Layout
- My Account
- User Complaint
  - To establish a new complaint session
  - To make a reply in a complaint session
- Data Logging
  - To make a reply in a Data Logging session
- Communities
  - To start a discussion
  - To join and reply to a discussion post
- Training Channels
- FAQ Database
15Quick Link
- To open a quick link
16Function Viewer
- To Search by the vehicle
- Search by the functions
17Maintenance and Service
- Maintenance Instructions
- Troubleshooting Checklist
- About Battery Usage
- Service Procedures
18Compliance Information
- FCC ComplianceFCC ID: WQ81806-808BT
- SAR
- RF WARNING STATEMENT
- RoHS COMPLIANCE
- CE COMPLIANCE
19Warranty
- Limited One Year Warranty
  - This warranty does not apply to:
    - IMPORTANT

135

RoHS COMPLIANCE

This device is declared to be in compliance with the European RoHS

Directive 2011/65/EU.

CE COMPLIANCE

This product is declared to conform to the essential requirements of the

following Directives and carries the CE mark accordingly:

EMC Directive 2014/30/EU

R&TTE Directive 2014/53/EU

Low Voltage Directive 2014/35/EU