User manual
Table Of Contents
- User Manual
- EVO Nano Series
- Terms for Usage
- Trademark Information
- Copyright
- Disclaimer
- Data Storage and Use
- Table of contents
- Chapter 1 Read Instructions
- Chapter 2 Aircraft
- ① Propeller
- ④ Forward visual system
- ② Motor
- ⑤ Antenna
- ③ PTZ camera
- ⑥ Rear vision system
- ⑨ USB-C port
- ⑦ Power button
- ⑩ Rear LED indicator
- ⑧ Aircraft battery
- ⑪ SD card slot
- ⑫ Air outlet
- ⑬ Ultrasonic sensor
- ⑮ Air inlet
- ⑭ Downward vision system
- There is an LED indicator on the tail of the aircr
- Status Definition of Flight LED Indicator
- Back LED Indicator
- Meaning
- Normal status
- Green light flashes slowly (1 flash every 2 second
- Aircraft in GPS mode
- Yellow light flashes slowly (1 flash per second)
- Aircraft in ATTI mode
- Pairing
- Green light flashes quickly
- Aircraft and remote controller are pairing
- Green light stays on for 5 seconds
- Pairing successful
- Red light stays on for 5 seconds
- Pairing failed
- Compass calibration
- Yellow light is on
- Starting compass calibration
- Yellow light is on
- Calibration failed
- Green light is on
- Calibration successful
- Warning
- Yellow light flashes slowly (1 flash per second)
- Low battery warning
- Red light flashes slowly (1 flash per second)
- Critical low battery alert
- Updating
- Green light flashes quickly
- Aircraft is updating
- Green light is is on
- Update successful
- Yellow light flashes slowly (1 flash per second)
- Update failed
- The battery for EVO Nano is 2250mAh and has the ra
- The battery indicator is divided into LED 1, LED 2
- Chapter 3 Remote controller
- Chapter 4 Autel Sky App
- Chapter 5 Flight
- 1) As shown in figure, press the left and right st
- 2) Slowly push up the left stick.
- 1) Press and slide the one-click takeoff button (
- 2) The aircraft will automatically rise to the hei
- Class I: main airport & low-altitude area for mann
- Class II: Sensitive area or organization & militar
- Chapter 6 Maintenance and service
- Chapter 7 Technical Specification
Scope of service:
Within the warranty period, the product has the non-human performance fault during
normal use;
The product is not disassembled without approval or modified or added as instructed by
non-official manual, or has other non-human faults;
The equipment serial number, factory label and other marks are not torn away or altered;
The effective proof of purchase, document and document number are provided;
The implementation of the specific rules of this service is subject to the local policies,
laws and regulations of different countries and regions.
This warranty clause will not be applied:
When the product is out of the warranty period;
When the battery has been charged for more than 200 times;
When the product doesn't use the official latest firmware;
When the fault is caused when product is used for unlawful activities;
When the product flight log has been changed or deleted without approval;
When the serial number label and waterproof mark of the product are damaged or
altered;
When the product has appearance, decorative or structural (such as frame and
non-operating component) defects;
When the damage is caused because it is not installed, used and operated as instructed by
the manual;
When the product damage is caused because of the use of the self-programming or
non-official software;
When the damage is caused by the reliability and compatibility problems when the
product is used with the component of a third party other than Autel Robotic;
When the product suffers from abnormal use or environment, accident or improper
handling, unauthorized change, abuse, or improper installation, maintenance or storage;
When the product is damaged due to external factors, including but not limited to, natural
disaster, fire, water, dirt, dust, battery leakage, fuse burn-out, theft or any improper use
of power supply;
When user fails to send the product within 7 natural days after contacting Autel Robotic