QUICK START GUIDE Enterprise
Contents �. GETTING TO KNOW THE EVO II ENTERPRISE .................................. � �. AIRCRAFT FRONT, REAR, AND LEFT SIDE VIEWS ............................. � �. AIRCRAFT RIGHT SIDE, TOP, AND BOTTOM VIEWS .......................... � �. FLIGHT LED INDICATIONS ................................................................ � �. SMART CONTROLLER ....................................................................... � �. CHARGING THE AIRCRAFT AND SMART CONTROLLER ................... � �.
1. GETTING TO KNOW THE EVO II ENTERPRISE Now you can explore, discover and create like never before. The EVO II Enterprise delivers not only advanced features like obstacles avoidance and intelligent flights modes, but also high-tech muscle that brings home a top speed of �� mph, ��-minute flight time, and an operating distance at � miles(FCC standard). In-flight performance, however, is just the start.
2.
3.
19 21 20 Bottom View 19 20 21 Ultrasonic Sensor Downward Vision Lighting LED Downward Vision System 4.FLIGHT INDICATION LIGHT A LED indicator is located on the end of each aircraft arm. The front LEDs will light up solid red to help you identify the direction of the aircraft's nose. The rear LEDs will display the current flight status of the aircraft. The chart below shows the meaning of each status indicator.
Definitions of Flight LED Indicator Status RGY ‒ Alternate Flashing YG - Alternate Flashing G ‒ Slow Flashing Normal Status System self-test is activated The aircraft is warming up The aircraft is in GPS mode Warning The aircraft is in ATTI mode Y - Slow Flashing No connection between the aircraft Y - Fast Flashing and smart controller R - Slow Flashing Low Battery Warning R - Fast Flashing Critically Low Battery Warning R ‒ Solid Light RY ‒ Alternate Flashing Critical problems, IMU error Ab
5. SMART CONTROLLER 4 1 2 3 4 5 6 7 5 6 7 8 9 10 3 11 2 12 1 13 Left Command Stick Top View 8 Gimbal Pitch Dial 9 Record Button 10 Air Vent 12 Customizable Button C� 11 HDMI Port 13 USB TYPE-C Port USB TYPE-A Port Power Button Customizable Button C� Photo Shutter Button * Zoom Control Wheel Right Command Stick * The function may alter, please take the practical effect as standard.
⑭ Battery Indicator ⑰ Pause Button ⑯ Touch Screen ⑲ Microphone ⑮ Antennas ⑱ Go Home Button 20 21 24 22 23 Rear View ⑳ Sound Speaker ㉑ Tripod Mount ㉒ Air Vent ㉓ Bottom Hook ㉔ Protection Case 6. CHARGING THE AIRCRAFT AND SMART CONTROLLER (�) Aircraft Battery: Plug the charging connector into the battery's charge port.
(�) Smart Controller: Open the protector on the USB port and plug in the provided charging cable. NOTE · Always fully charge the aircraft and smart controller battery before flying. ·It takes approximately �� minutes to fully charge the aircraft battery, and ��� minutes to charge the smart controller. 7. Autel ExplorerTM APP The Autel Explorer™ App is built in the smart controller, and it is used to control the aircraft. Autel Explorer™ App is optimized for EVO II Enterprise.
8. PREPARING THE AIRCRAFT （�）Before powering on the aircraft, please remove the gimbal guard. Slowly pull it away from the aircraft as shown below. （�）Unfold the arms and propellers IMPORTANT Power off the aircraft before folding the arms. Fold in the rear arms and propellers first, and then the front ones.
9. INSTALLING NEW PROPELLERS Because the propellers come attached to the aircraft, the following instructions apply if you need to reinstall propellers. Propellers must be undamaged and firmly attached. · Attaching the Propellers （�）Verify that the aircraft is powered off. （�）Locate and match the propeller to each motor （�）Press each propeller down firmly and rotate in the lock direction to securely attach the propeller.
WARNING Power off the aircraft before attaching or detaching propellers. IMPORTANT Wear protective gloves when attaching or detaching propellers. 10. ENTERPRISE ACCESSORIES The EVO II Enterprise can be equipped with accessories for different applications. Optional accessories: Spotlight, Loudspeaker, Strobe, and RTK module.
· Detach the accessory （�）Please ensure the aircraft is powered off. （�）Lose the screws on both sides, and remove the accessory. （�）Insert both ends of the protective cover into the corresponding slots. · Attach the accessory （�）Please ensure the aircraft is powered off. （�）Lightly squeeze both ends to remove the protective cover （�）Align the screws on both sides of the accessory with the screw holes and tighten the screws. 11.
���o 12. POWERING UP （�）Press and hold the power button for � second to turn on the smart controller. （�）Press and hold the power button � seconds to turn on the aircraft. The current battery level will be clearly displayed.
13. TAKEOFF （�）Place aircraft on a level surface, Stand well clear of the rear of the aircraft. （�）Start the motors by holding both command sticks for two seconds in the one of these positions as shown below: or （�）With the motors spinning, choose one of the following methods to take off: Hold the Takeoff/Landing Button for �s Push the Left Command Stick slowly upward (Mode �) Note: Before takeoff, place the aircraft on a flat and level surface and face the rear side of the aircraft towards you.
14.
WWW.AUTELROBOTICS.COM ©����-���� AUTEL ROBOTICS CO., LTD.
