QUICK GUIDE For EVO II Dual 640T
Contents 1. WELCOME TO THE EVO II Dual 640T 2. AIRCRAFT FRONT, REAR, & LEFT VIEWS ........................................... 1 ......................................... 1 3. AIRCRAFT RIGHT, TOP, & BOTTOM VIEWS ....................................... 2 4. FLIGHT LED INDICATORS ........................................... 4 5. REMOTE CONTROL ........................................... 5 6. CHARGING THE AIRCRAFT & REMOTE CONTROL ............................. 6 7.
1. WELCOME TO THE EVO II Dual 640T Welcome to the Autel Robotics family! Now you can explore, discover and create like never before. The EVO II Dual 640T delivers not only advanced features like obstacle avoidance and intelligent flight modes, but also high-tech muscle that brings home a top speed of 45mph, 33-minute hover time, 38-minute flight time and an operating distance of 5.6 miles. In-flight performance is just the start.
1 Propellers 4 Landing Gear 2 Motors 5 Forward Vision System 3 Front LED Indicators 6 Camera Gimbal 7 9 8 Rear Side 7 Power Button 9 Rear LED Indicators 8 Rear Vision System 10 11 Left Side 11 SD Card Port 10 Left Vision System 3.
12 Right Vision System 13 Aircraft Battery 14 Fan Exhaust 15 USB Port 16 Remote Control Pairing Button/Pairing Indicator 17 Top Side 17 Top Vision System 18 20 19 Bottom Side 18 Ultrasonic Sensor 19 Downward Vision Lighting LED 20 Downward Vision System 3
4. FLIGHT LED INDICATIONS A LED indicator is located on the end of each aircraft arm. The front LEDs will light up solid red to help you identify the direction of the aircraft's nose. The rear LEDs will display the current flight status of the aircraft. The chart below shows the meaning of each status indicator.
Calibration is failed R - Solid Light Gesture Commands R - Fast Flashing Gesture command has been received 5.
11 12 17 13 16 15 14 11 Screen Navigation Dial Scrolls around the OLED screen 12 Screen Navigation Button When the mobile device is disconnected, press this button for 1 second to enter/exit the Image Transmission screen on the remote control 13 Shutter Button Takes photos. When Burst Mode is in use, several images will be taken with one press. For details, see the App Manual.
1) Aircraft Battery: Plug the charging connector into the battery’s charge port. 2) Remote Control: Open the protector on the USB port and plug in the provided charging cable. NOTE • Always fully charge the aircraft and remote control battery before flying. • It takes approximately 90 minutes to fully charge the aircraft battery, and 180 minutes to charge the remote control. 7.
2) Unfold the arms and propellers IMPORTANT Ensure the aircraft is powered off before folding the arms. Fold in the rear arms and propellers first, and then the front arms. 9. INSTALLING NEW PROPELLERS The propellers come already attached to the aircraft, the following instructions only apply if you need to reinstall the propellers. Before each flight check the propellers for damage and ensure they are firmly attached. The white-coded propellers are paired with the white-coded motors.
Legend Lock Direction: Fasten the propeller by rotating it as indicated. Unlock Direction: Unfasten the propeller by rotating it as indicated. Black-coded propeller > Pairs with > Black-coded motor White-coded propeller > Pairs with > White-coded motor WARNING Power off the aircraft before attaching or detaching propellers. IMPORTANT Wear protective gloves when attaching or detaching propellers. 10. PREPARING THE REMOTE CONTROL 1). Unfold the hand grips, mobile device holder, and antennas. 2).
11. POWERING UP 1.Turn on the remote control. Press and hold the power button for 2 seconds. 2. Turn on the aircraft. Press and hold the aircraft power button for 3 seconds. The current battery level will be clearly displayed. 12. TAKEOFF 1. Place aircraft on a level surface. Stand clear of the aircraft. 2. Start the motors by holding both command sticks for two seconds in one of these positions: or 3.
13.
2020-2021 Autel Robotics Co., Ltd.
