Users Manual

ISEDC Warning
Operation of 5150-5250 MHz is restricted to indoor use only.
This device complies withInnovation, Science, and Economic Development
standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le fonctionnement de 5150-5250 MHz estlimité àuneutilisation en intérieuruniquement.
Le présentappareilestconforme aux CNR d' Innovation,Sciences et Développementéconomique
Canada applicables aux appareils radio exempts delicence. L'exploitationestautorisée aux
suivantes :
(1) l'appareilnedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi,
Canadalicence-exempt RSS
deux conditions
mêmesilebrouillageest susceptible d'encompromettre le fonctionnement.
IMPORTANT NOTE:
Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating
positions accepted by the ISEDC with the device transmitting at its highest certified power level
in all tested frequency bands, although the SAR is determined at the highest certified power
level, the actual SAR level of the device while operating can be well below the maximum value,
in general, the closer you are to a wireless base station antenna, the lower the power output.
Before a new model device is a available for sale to the public, it must be tested and certified to
the ISEDC that it does not exceed the exposure limit established by the ISEDC, Tests for each
device are performed in positions and locations (e.g. at the ear and worn on the body)as
required by the ISEDC.
For limb worn operation, this device has been tested and meets the ISEDCRF exposure
guidelines when used with an accessory designated for this product or when used
with an accessory that contains no metal.
For body worn operation, this device has been testedand meets the ISEDC RF exposure
guidelines when used with an accessory designated for thisproduct or when used with an
accessory that contains no metal and that positions the device aminimum of 10mm from the
body.
Tauxd’absorptionspécifique (SAR) informations les tests SAR
sonteffectués en utilisant les positions opérationnellesnormaliséesacceptéespar la ISEDC, le
dispositifémettant à son niveau de puissance certifié le plus élevédanstoutes les
bandesdefréquencestestées.Avantqu’un nouveau modèle de dispositif ne soitdisponible à la
vente aupublic, ildoitêtretesté et certifié à la ISEDC qu’il ne dépasse pas la
Pour le fonctionnement desmembresusés, cetappareil a ététesté et répond aux
lignesdirectricesd’exposition aux RF ISEDClorsqu’ilestutilisé avec un accessoiredésigné pour
ceproduitoulorsqu’ilestutilisé avec unaccessoire qui ne contient pas de métal.
Pour le fonctionnement du corps usé, cetappareil a ététesté et répond aux
lignesdirectricesd’exposition RF ISEDC lorsqu’ilestutilisé avec un accessoiredésigné pour
ceproduitoulorsqu’ilestutilisé avec un accessoire qui ne contient pas de métal etqui
limited’expositionétablieparla ISEDC, les Tests pour chaquedispositifsonteffectuésdans des
positions et des emplacements(par exemple à l’oreille et portésur le corps) commel’exige la
ISEDC.
positionnecet appareil à au moins 10mm du corps.
Step1:Select“Camera”
Step2:Click the gear icon in the upper right corner,enter the settings menu
Step3:Select“Certification Mark”
Steps to use electronic tags