EVO Nano Series User Manual
Table Of Contents
- User Manual
- EVO Nano Series
- Terms for Usage
- Trademark Information
- Copyright
- Disclaimer
- Data Storage and Use
- Table of contents
- Chapter 1 Read Instructions
- Chapter 2 Aircraft
- ① Propeller
- ④ Forward visual system
- ② Motor
- ⑤ Antenna
- ③ PTZ camera
- ⑥ Rear vision system
- ⑨ USB-C port
- ⑦ Power button
- ⑩ Rear LED indicator
- ⑧ Aircraft battery
- ⑪ SD card slot
- ⑫ Air outlet
- ⑬ Ultrasonic sensor
- ⑮ Air inlet
- ⑭ Downward vision system
- There is an LED indicator on the tail of the aircr
- Status Definition of Flight LED Indicator
- Back LED Indicator
- Meaning
- Normal status
- Green light flashes slowly (1 flash every 2 second
- Aircraft in GPS mode
- Yellow light flashes slowly (1 flash per second)
- Aircraft in ATTI mode
- Pairing
- Green light flashes quickly
- Aircraft and remote controller are pairing
- Green light stays on for 5 seconds
- Pairing successful
- Red light stays on for 5 seconds
- Pairing failed
- Compass calibration
- Yellow light is on
- Starting compass calibration
- Yellow light is on
- Calibration failed
- Green light is on
- Calibration successful
- Warning
- Yellow light flashes slowly (1 flash per second)
- Low battery warning
- Red light flashes slowly (1 flash per second)
- Critical low battery alert
- Updating
- Green light flashes quickly
- Aircraft is updating
- Green light is is on
- Update successful
- Yellow light flashes slowly (1 flash per second)
- Update failed
- The battery for EVO Nano is 2250mAh and has the ra
- The battery indicator is divided into LED 1, LED 2
- Chapter 3 Remote controller
- Chapter 4 Autel Sky App
- Chapter 5 Flight
- 1) As shown in figure, press the left and right st
- 2) Slowly push up the left stick.
- 1) Press and slide the one-click takeoff button (
- 2) The aircraft will automatically rise to the hei
- Class I: main airport & low-altitude area for mann
- Class II: Sensitive area or organization & militar
- Chapter 6 Maintenance and service
- Method 1: download firmware upgrade package from A
- Method 2: download firmware upgrade package from t
- Chapter 7 Technical Specification
When the serial number label and waterproof mark of the product are damaged or
altered;
When the product has appearance, decorative or structural (such as frame and
non-operating component) defects;
When the damage is caused because it is not installed, used and operated as instructed by
the manual;
When the product damage is caused because of the use of the self-programming or
non-official software;
When the damage is caused by the reliability and compatibility problems when the
product is used with the component of a third party other than Autel Robotic;
When the product suffers from abnormal use or environment, accident or improper
handling, unauthorized change, abuse, or improper installation, maintenance or storage;
When the product is damaged due to external factors, including but not limited to, natural
disaster, fire, water, dirt, dust, battery leakage, fuse burn-out, theft or any improper use of
power supply;
When user fails to send the product within 7 natural days after contacting Autel Robotic
for warranty service.
6.4 Customer service
This section includes the information on technical support, maintenance service, application
for replacement and spare parts.
6.4.1 Technical support
If you have any problems or questions about our product, please contact Autel Robotics’
customer support:
North America/Europe
Tel: (844) 692-8835
Email: support@autelrobotics.com / support.eu@autelrobotics.com
Website: www.autelrobotics.com