EVO Nano Series User Manual
Table Of Contents
- User Manual
- EVO Nano Series
- Terms for Usage
- Trademark Information
- Copyright
- Disclaimer
- Data Storage and Use
- Table of contents
- Chapter 1 Read Instructions
- Chapter 2 Aircraft
- ① Propeller
- ④ Forward visual system
- ② Motor
- ⑤ Antenna
- ③ PTZ camera
- ⑥ Rear vision system
- ⑨ USB-C port
- ⑦ Power button
- ⑩ Rear LED indicator
- ⑧ Aircraft battery
- ⑪ SD card slot
- ⑫ Air outlet
- ⑬ Ultrasonic sensor
- ⑮ Air inlet
- ⑭ Downward vision system
- There is an LED indicator on the tail of the aircr
- Status Definition of Flight LED Indicator
- Back LED Indicator
- Meaning
- Normal status
- Green light flashes slowly (1 flash every 2 second
- Aircraft in GPS mode
- Yellow light flashes slowly (1 flash per second)
- Aircraft in ATTI mode
- Pairing
- Green light flashes quickly
- Aircraft and remote controller are pairing
- Green light stays on for 5 seconds
- Pairing successful
- Red light stays on for 5 seconds
- Pairing failed
- Compass calibration
- Yellow light is on
- Starting compass calibration
- Yellow light is on
- Calibration failed
- Green light is on
- Calibration successful
- Warning
- Yellow light flashes slowly (1 flash per second)
- Low battery warning
- Red light flashes slowly (1 flash per second)
- Critical low battery alert
- Updating
- Green light flashes quickly
- Aircraft is updating
- Green light is is on
- Update successful
- Yellow light flashes slowly (1 flash per second)
- Update failed
- The battery for EVO Nano is 2250mAh and has the ra
- The battery indicator is divided into LED 1, LED 2
- Chapter 3 Remote controller
- Chapter 4 Autel Sky App
- Chapter 5 Flight
- 1) As shown in figure, press the left and right st
- 2) Slowly push up the left stick.
- 1) Press and slide the one-click takeoff button (
- 2) The aircraft will automatically rise to the hei
- Class I: main airport & low-altitude area for mann
- Class II: Sensitive area or organization & militar
- Chapter 6 Maintenance and service
- Method 1: download firmware upgrade package from A
- Method 2: download firmware upgrade package from t
- Chapter 7 Technical Specification
www.autelrobotics.com.
2. Insert SD card into your computer, save the downloaded firmware package under the root
directory of SD card.
3. Turn on your remote controller and aircraft, connect your mobile phone to the remote
controller, operate Autel Sky app.
4. Insert SD card into the aircraft for automatic update. User can view the upgrade process on
App interface.
5. Please restart the aircraft and the remote controller after update.
Important
Before firmware update, please ensure that:
Update the firmware by step, otherwise the update may be failed. The aircraft will shut
down automatically after update.
If the device is closed during update, the update may be failed.
In the case of network outage during update, the update may be failed.
The whole update process will take more than ten minutes. The following situations may
occur in the aircraft during update: it is normal that the gimbal is weak, the status
indicator flashes abnormally, or the aircraft restarts; Please wait patiently for completing
firmware update.
Ensure that the aircraft and remote controller have the battery level of more than 30%.
After the firmware update, the flight control parameters such as return height and
distance limit of the aircraft will be reset. Please reset them after update.
6.2 Storage and maintenance
In order to ensure the optimal performance of EVO Nano, please read and abide by the
maintenance instruction of this section carefully.
Store the aircraft, battery and remote controller in a clean, dry, cool and well-ventilated
place.
Protect the aircraft from direct sunlight when it is not used.
Please wipe dry your two hands before operating the aircraft.
Clean the camera lens with the soft cloth with alcohol or gentle window cleanser. Do not