EVO Nano Series User Manual
Table Of Contents
- User Manual
- EVO Nano Series
- Terms for Usage
- Trademark Information
- Copyright
- Disclaimer
- Data Storage and Use
- Table of contents
- Chapter 1 Read Instructions
- Chapter 2 Aircraft
- ① Propeller
- ④ Forward visual system
- ② Motor
- ⑤ Antenna
- ③ PTZ camera
- ⑥ Rear vision system
- ⑨ USB-C port
- ⑦ Power button
- ⑩ Rear LED indicator
- ⑧ Aircraft battery
- ⑪ SD card slot
- ⑫ Air outlet
- ⑬ Ultrasonic sensor
- ⑮ Air inlet
- ⑭ Downward vision system
- There is an LED indicator on the tail of the aircr
- Status Definition of Flight LED Indicator
- Back LED Indicator
- Meaning
- Normal status
- Green light flashes slowly (1 flash every 2 second
- Aircraft in GPS mode
- Yellow light flashes slowly (1 flash per second)
- Aircraft in ATTI mode
- Pairing
- Green light flashes quickly
- Aircraft and remote controller are pairing
- Green light stays on for 5 seconds
- Pairing successful
- Red light stays on for 5 seconds
- Pairing failed
- Compass calibration
- Yellow light is on
- Starting compass calibration
- Yellow light is on
- Calibration failed
- Green light is on
- Calibration successful
- Warning
- Yellow light flashes slowly (1 flash per second)
- Low battery warning
- Red light flashes slowly (1 flash per second)
- Critical low battery alert
- Updating
- Green light flashes quickly
- Aircraft is updating
- Green light is is on
- Update successful
- Yellow light flashes slowly (1 flash per second)
- Update failed
- The battery for EVO Nano is 2250mAh and has the ra
- The battery indicator is divided into LED 1, LED 2
- Chapter 3 Remote controller
- Chapter 4 Autel Sky App
- Chapter 5 Flight
- 1) As shown in figure, press the left and right st
- 2) Slowly push up the left stick.
- 1) Press and slide the one-click takeoff button (
- 2) The aircraft will automatically rise to the hei
- Class I: main airport & low-altitude area for mann
- Class II: Sensitive area or organization & militar
- Chapter 6 Maintenance and service
- Method 1: download firmware upgrade package from A
- Method 2: download firmware upgrade package from t
- Chapter 7 Technical Specification
Chapter 5 Flight
EVO Nano series adopts the unique portable design and has been assembled in factory. In
order to ensure safe operation of UAV, please read the following instructions and warnings
before first flight.
5.1 Safe operation guide
5.1.1 Flight environment
Please abide by the local laws and regulations on UAV flight. Fly only in the designated
aircraft movement area, and use Autel Sky App to set the satisfactory distance and height
limits.
Never fly in severe weather such as heavy fog, rain, hail, snow, high wind (force 5 and
above) and so on.
Please fly in an open area away from densely-populated area, building and
electromagnetic interference source. The building containing more reinforcement bars
will affect the operation of compass and block the GPS signal, causing the poor
positioning of aircraft and even positioning failure. It is recommended to keep the
aircraft from the building by at least 5m.
Please fly in the area where the altitude is 4000m below.
In the case of flying indoors, some functions may be limited due to insufficient light, lack
of GPS signal or narrow space.
Please control the aircraft within the range of visibility, and keep it away from obstacle,
crowd, water surface (by 3m above), etc.
5.1.2 Pre-flight
Before the UAV flies, it is always necessary to pay attention to the following matters:
Ensure that the aircraft, remote controller and mobile device are fully charged.
Ensure that the protective cover for gimbal have been removed.
Ensure that the aircraft camera lens and sensor keep clean.
Ensure that the propeller has been installed correctly without damage.
Ensure that each component of the aircraft has been assembled.