EVO Nano Series User Manual
Table Of Contents
- User Manual
- EVO Nano Series
- Terms for Usage
- Trademark Information
- Copyright
- Disclaimer
- Data Storage and Use
- Table of contents
- Chapter 1 Read Instructions
- Chapter 2 Aircraft
- ① Propeller
- ④ Forward visual system
- ② Motor
- ⑤ Antenna
- ③ PTZ camera
- ⑥ Rear vision system
- ⑨ USB-C port
- ⑦ Power button
- ⑩ Rear LED indicator
- ⑧ Aircraft battery
- ⑪ SD card slot
- ⑫ Air outlet
- ⑬ Ultrasonic sensor
- ⑮ Air inlet
- ⑭ Downward vision system
- There is an LED indicator on the tail of the aircr
- Status Definition of Flight LED Indicator
- Back LED Indicator
- Meaning
- Normal status
- Green light flashes slowly (1 flash every 2 second
- Aircraft in GPS mode
- Yellow light flashes slowly (1 flash per second)
- Aircraft in ATTI mode
- Pairing
- Green light flashes quickly
- Aircraft and remote controller are pairing
- Green light stays on for 5 seconds
- Pairing successful
- Red light stays on for 5 seconds
- Pairing failed
- Compass calibration
- Yellow light is on
- Starting compass calibration
- Yellow light is on
- Calibration failed
- Green light is on
- Calibration successful
- Warning
- Yellow light flashes slowly (1 flash per second)
- Low battery warning
- Red light flashes slowly (1 flash per second)
- Critical low battery alert
- Updating
- Green light flashes quickly
- Aircraft is updating
- Green light is is on
- Update successful
- Yellow light flashes slowly (1 flash per second)
- Update failed
- The battery for EVO Nano is 2250mAh and has the ra
- The battery indicator is divided into LED 1, LED 2
- Chapter 3 Remote controller
- Chapter 4 Autel Sky App
- Chapter 5 Flight
- 1) As shown in figure, press the left and right st
- 2) Slowly push up the left stick.
- 1) Press and slide the one-click takeoff button (
- 2) The aircraft will automatically rise to the hei
- Class I: main airport & low-altitude area for mann
- Class II: Sensitive area or organization & militar
- Chapter 6 Maintenance and service
- Method 1: download firmware upgrade package from A
- Method 2: download firmware upgrade package from t
- Chapter 7 Technical Specification
share it to other social platform.
5. After user clicks the photo/video button on APP camera interface, uses the command stick
of remote controller or short presses the remote controller pause button ( ) to quit the
short film shooting, the aircraft will brake and hover at current position, and the materials
taken before such interruption will be saved in album.
Important
Please use the short film shooting in an open environment free of obstacle and blockage.
Pay close attention to any pedestrian, vehicle, animal or other obstacles in the
surrounding environment to avoid the occurrence of accident.
The distance between aircraft and remote controller shall maintain within 30m, and the
aircraft shall be within the range of operator’s visibility.
Please do not use the one-click short film function in the case of the poor GPS signal due
to building or blockage, otherwise this may cause unstable flight path of aircraft or other
accidents.
When using the one-click short film function, user shall abide by the local laws on
privacy right.
In the following scenes, the vision system of Nano series will not operate normally, so it
is inadvisable to use the one-click short film function:
– When the object being shot is blocked for long or located outside the range of
visibility;
– When the object being shot is more than 50m from the aircraft;
– When the object being shot has very similar color or pattern with the surrounding
environment;
– When the object being shot is located in the air;
– When the object being shot moves quickly;
– In a particularly dark (illumination less than 300 lux) or bright (illumination greater
than 10,000 lux) environment.