EVO Nano Series User Manual
Table Of Contents
- User Manual
- EVO Nano Series
- Terms for Usage
- Trademark Information
- Copyright
- Disclaimer
- Data Storage and Use
- Table of contents
- Chapter 1 Read Instructions
- Chapter 2 Aircraft
- ① Propeller
- ④ Forward visual system
- ② Motor
- ⑤ Antenna
- ③ PTZ camera
- ⑥ Rear vision system
- ⑨ USB-C port
- ⑦ Power button
- ⑩ Rear LED indicator
- ⑧ Aircraft battery
- ⑪ SD card slot
- ⑫ Air outlet
- ⑬ Ultrasonic sensor
- ⑮ Air inlet
- ⑭ Downward vision system
- There is an LED indicator on the tail of the aircr
- Status Definition of Flight LED Indicator
- Back LED Indicator
- Meaning
- Normal status
- Green light flashes slowly (1 flash every 2 second
- Aircraft in GPS mode
- Yellow light flashes slowly (1 flash per second)
- Aircraft in ATTI mode
- Pairing
- Green light flashes quickly
- Aircraft and remote controller are pairing
- Green light stays on for 5 seconds
- Pairing successful
- Red light stays on for 5 seconds
- Pairing failed
- Compass calibration
- Yellow light is on
- Starting compass calibration
- Yellow light is on
- Calibration failed
- Green light is on
- Calibration successful
- Warning
- Yellow light flashes slowly (1 flash per second)
- Low battery warning
- Red light flashes slowly (1 flash per second)
- Critical low battery alert
- Updating
- Green light flashes quickly
- Aircraft is updating
- Green light is is on
- Update successful
- Yellow light flashes slowly (1 flash per second)
- Update failed
- The battery for EVO Nano is 2250mAh and has the ra
- The battery indicator is divided into LED 1, LED 2
- Chapter 3 Remote controller
- Chapter 4 Autel Sky App
- Chapter 5 Flight
- 1) As shown in figure, press the left and right st
- 2) Slowly push up the left stick.
- 1) Press and slide the one-click takeoff button (
- 2) The aircraft will automatically rise to the hei
- Class I: main airport & low-altitude area for mann
- Class II: Sensitive area or organization & militar
- Chapter 6 Maintenance and service
- Method 1: download firmware upgrade package from A
- Method 2: download firmware upgrade package from t
- Chapter 7 Technical Specification
Remark
The vision system has dead zone outside its covering range. It is necessary to pay
attention to the ambient environment and App notice during flight to ensure safety.
Do not operate the aircraft in a complex environment where there is insufficient light,
small object (such as twig, line, net), moving object, transparent surface (such as window)
or reflected surface (such as mirror).
In the case of flight with car or other vehicles, please select a field or closed road for
driving. Never use it on highway.
2.7.1 Precautions
1. Ensure that the aircraft is in GPS or vision positioning mode.
2. The aircraft shall take off when the flight LED indicator flashes green slowly or red twice.
3. When the GPS signal is weak or fails to meet the vision positioning requirement, it is
necessary to be extremely careful.
4. The vision system and ultrasonic system are affected by the surface brightness and texture
below the aircraft. Avoid flying above the following surfaces:
– Surface of pure color (such as pure black, pure white).
– Surface with high reflection or inverted reflection (such as ice surface).
–
Water surface or transparent surface.
–
Surface with frequently changing light.
– Particularly dark or bright object surface.
– Moving surface (such as road with heavy traffic).
–
Sound absorbing surface (such as thick carpet).
–
Surface with sparse texture (such as electric pole, pipeline, etc.).
–
Surface composed of highly repetitive pattern (such as tile).
–
Tiny obstacle (such as tree branch, electric wire, etc.).
5. Avoid flying in rainy and foggy weather or other scenes where the visibility lower than
100m.
6. Before flight check the vision system surface to ensure that the binocular camera lens and
sensor are clean and not covered.